A.R. Sudgen Connoisseur Bd1 Motor Parts/repair. This motor used to run but I will sell it as non working parts only. It’s been in a box for a while. The rubber has been long gone. Thanks for looking

Purchased in the 1970s Switches on ok and turntable spins but is very noisy. 2 speed, 33 & 45 rpm. Shure M75 type 2 cartridge & stylus included (stylus is separate and the protective sponge is disintegrating). SAU 2 pick up arm. Groov-Kleen cleaner. Stylus pressure gadget. The plinth cover is in good condition. Needs a 3 pin plug I would prefer collection from CM11 postcode. Will post but please bear in mind I do not have the transport screws. Any questions, please ask.

.AR Sugden Connoisseur BD1 /BD2 Turntable spares in used order-BRAKE ON/OFF LEVER/TONEARMWEIGHT AND DRIVE BELT ALL TAKEN FROM A WORKING TURNTABLE 9 YEARS AGO.NO TURNTABLE ONLY SPARES AS IN PICTURE.thanks for looking-UK BIDDERS ONLY AND NO BUY IT NOW.will not ship to shipping companies or alternative addresses.please text on 07933158535 any questions

.AR Sugden Connoisseur BD1 /BD2 Turntable spares in used order-BRAKE ON/OFF LEVER/TONEARMWEIGHT AND DRIVE BELT ALL TAKEN FROM A WORKING TURNTABLE 9 YEARS AGO.NO TURNTABLE ONLY SPARES AS IN PICTURE.thanks for looking-UK BIDDERS ONLY AND NO BUY IT NOW.will not ship to shipping companies or alternative addresses.please text on 07933158535 any questions

A R Sugden Connoisseur BD1 Turntable -Spares /Repairs. Not sure about the history with this one Was in amongst a job lot of turntables I purchased Has nice oak plinth in good condition , the platter seems to be missing the rubber mat , switch is missing the main on /off lever , motor and internal circuits all present no idea of the condition Great little project if anyone has the time !

Tapis pour platine disque Connoisseur BD 101 en très bon état.Diamètre:30cmEpaisseur: 4mm

Pieds suspensions pour platine Sugden Connoisseur BD 101 en très bon état + Visserie complète.

Porte Bras pour platine Connoisseur BD-101 et parfait état.

TURNTABLE MOTOR PULLEY REMOVER and ADJUSTER for CONNOISSEUR BD1 & BD2 Hand-crafted by Williams-Sonics, my Motor Puller enables easy and safe removal of pulleys from Connoisseur BD1 and BD2 turntable motors. It will remove them quickly and safely even if they are seized on through being very tight on the motor spindle or from not being moved for many years. Removing the pulleys by hand is possible but there is the real risk that you will irrevocably damage the motors performance. The slightest bend to the spindle will take the motor out of true alignment and the effect will be heard. Unfortunately, I have encountered several motors damaged in this way. It is impossible to repair such damage. I always use a removal tool as it is just not worth risking hand pulling when replacement motors are not available on these vintage turntables. Another essential use of this removal tool is in adjusting the pulley. Connoisseur pulleys have to be aligned, often by very small amounts. Pushing the pulley too low, then too high, then too low again in an attempt to find the right place for perfect running at both 33 and 45 rpm can be difficult. Using this tool it is easy to accurately move the pulley by micro amounts to precisely tune your turntables drive system.Included with the tool is a short stainless steel tube which can be placed over the motor spindle where the spindle protrudes very high above the pulley. The tool then fits into this tube making it simple to keep both aligned until the spindle is driven flush with the pulley. The puller is supplied with important advice gained from many years of experience with these motors and pulleys.The puller is discounted when purchased together with a suspension kit, please see my other listings. Kind regards,williams-sonics

TURNTABLE MOTOR PULLEY REMOVER and ADJUSTER for CONNOISSEUR BD1 & BD2 Hand-crafted by Williams-Sonics, my Motor Puller enables easy and safe removal of pulleys from Connoisseur BD1 and BD2 turntable motors. It will remove them quickly and safely even if they are seized on through being very tight on the motor spindle or from not being moved for many years. Removing the pulleys by hand is possible but there is the real risk that you will irrevocably damage the motors performance. The slightest bend to the spindle will take the motor out of true alignment and the effect will be heard. Unfortunately, I have encountered several motors damaged in this way. It is impossible to repair such damage. I always use a removal tool as it is just not worth risking hand pulling when replacement motors are not available on these vintage turntables. Another essential use of this removal tool is in adjusting the pulley. Connoisseur pulleys have to be aligned, often by very small amounts. Pushing the pulley too low, then too high, then too low again in an attempt to find the right place for perfect running at both 33 and 45 rpm can be difficult. Using this tool it is easy to accurately move the pulley by micro amounts to precisely tune your turntables drive system.Included with the tool is a short stainless steel tube which can be placed over the motor spindle where the spindle protrudes very high above the pulley. The tool then fits into this tube making it simple to keep both aligned until the spindle is driven flush with the pulley. The puller is supplied with important advice gained from many years of experience with these motors and pulleys.The puller is discounted when purchased together with a suspension kit, please see my other listings. Kind regards,williams-sonics

TURNTABLE MOTOR PULLEY REMOVER and ADJUSTER for CONNOISSEUR BD1 & BD2 Hand-crafted by Williams-Sonics, my Motor Puller enables easy and safe removal of pulleys from Connoisseur BD1 and BD2 turntable motors. It will remove them quickly and safely even if they are seized on through being very tight on the motor spindle or from not being moved for many years. Removing the pulleys by hand is possible but there is the real risk that you will irrevocably damage the motors performance. The slightest bend to the spindle will take the motor out of true alignment and the effect will be heard. Unfortunately, I have encountered several motors damaged in this way. It is impossible to repair such damage. I always use a removal tool as it is just not worth risking hand pulling when replacement motors are not available on these vintage turntables. Another essential use of this removal tool is in adjusting the pulley. Connoisseur pulleys have to be aligned, often by very small amounts. Pushing the pulley too low, then too high, then too low again in an attempt to find the right place for perfect running at both 33 and 45 rpm can be difficult. Using this tool it is easy to accurately move the pulley by micro amounts to precisely tune your turntables drive system. Included with the tool is a short stainless steel tube which can be placed over the motor spindle where the spindle protrudes very high above the pulley. The tool then fits into this tube making it simple to keep both aligned until the spindle is driven flush with the pulley. The puller is supplied with important advice gained from many years of experience with these motors and pulleys.The puller is discounted when purchased together with a suspension kit, please see my other listings. Kind regards,williams-sonics

EARLY MOTOR SUSPENSION FOR SUGDEN CONNOISSEUR TURNTABLES Fits: ALL EARLY BD-1, BD-2-& BD2A. Cut Band Suspension for ALL EARLY BD1, BD2, BD2A. Motors. This is a very effective suspension that will fit all early motors regardless of the anti-reverse mechanisms position in your motor. This rubber is a soft natural rubber with the perfect properties and excellent resistance to oxidisation, meaning it will last. The quality and performance of suspensions made using this rubber are excellent because of the rubbers natural elasticity. I have a very limited amount of this special natural rubber with no way of obtaining further supply. Nevertheless, I am pleased to be able to offer this kit while I can for all early motors on Connoisseur BD1 & BD2 turntables. These kits are already in use by owners not able to use my web based Conversion kit. This suspension is a Cut Band Suspension, featuring an easy mounting system. It comes as an all hand-made kit which includes the following: Three natural rubber hand cut suspension bands.Six adjustable fixings for the cut bands.One williams-sonics Gold Glass drive belt matched to the cut band suspension.Three natural rubber counter tension bands (graduated in size).One natural rubber insert for your SAU2 bias weight with alignment tool.Instructions which are easy to follow and produce perfect results.I am available for support with fitting through eBay messages.The plastic suspension plate ( hanger plate) which holds the motor to the metal plinth that have a 30mm hole in the centre need no mod. The ones with 20mm diameter hole will need a small semicircle filling inside opposite the lugs, see drawing in second photo. Please note this is a hand made Cut Band Suspension not a web suspension and is designed for early motors only and will not fit later motors. For later motors see my Service kits. If you would prefer a web suspension for your early motor and your motor has its anti-reverse mechanism at its bottom see my Conversion Suspension kit. Contact me if you have any questions, I aim to provide a prompt response. It is coincidental in this period of crisis that the barriers being employed for health reasons are ones that I already use to protect myself in my workshop and have been using for the past three years. The materials I use have always been initially cleaned with isopropanol alcohol before and at various stages of my work with them. I wear a very effective industrial rubber face mask because I do not want to ingest fine rubber particles. Also I wear eye protection against any materials and machine parts that can fly towards my face. Now I wear nitrile gloves for all the processes including packing. All reseal-able plastic bags are wiped over with isopropanol. Kind regards, williams-sonics

EARLY MOTOR SUSPENSION FOR SUGDEN CONNOISSEUR TURNTABLES Fits: ALL EARLY BD-1, BD-2-& BD2A. Cut Band Suspension for ALL EARLY BD1, BD2, BD2A. Motors. This is a very effective suspension that will fit all early motors regardless of the anti-reverse mechanisms position on your motor. This rubber is a soft natural rubber with the perfect properties and excellent resistance to oxidisation, meaning it will last. The quality and performance of suspensions made using this rubber are excellent because of the rubbers natural elasticity. I have a very limited amount of this special natural rubber with no way of obtaining further supply. Nevertheless, I am pleased to be able to offer this kit while I can for all early motors on Connoisseur BD1 & BD2 turntables. These kits are already in use by owners not able to use my web based Conversion kit. This suspension is a Cut Band Suspension, featuring an easy mounting system. It comes as an all hand-made kit which includes the following: Three natural rubber hand cut suspension bands.Six adjustable fixings for the cut bands.One williams-sonics Gold Glass drive belt matched to the cut band suspension.Three natural rubber counter tension bands (graduated in size).One natural rubber insert for your SAU2 bias weight with alignment tool.Instructions which are easy to follow and produce perfect results.I am available for support with fitting through eBay messages.The plastic suspension plate ( hanger plate) which holds the motor to the metal plinth that have a 30mm hole in the centre need no mod. The ones with 20mm diameter hole will need a small semicircle filling inside opposite the lugs, see drawing in second photo. Please note this is a hand made Cut Band Suspension not a web suspension and is designed for early motors only and will not fit later motors. For later motors see my Service kits. If you would prefer a web suspension for your early motor and your motor has its anti-reverse mechanism at its bottom see my Conversion Suspension kit. Contact me if you have any questions, I aim to provide a prompt response. It is coincidental in this period of crisis that the barriers being employed for health reasons are ones that I already use to protect myself in my workshop and have been using for the past three years. The materials I use have always been initially cleaned with isopropanol alcohol before and at various stages of my work with them. I wear a very effective industrial rubber face mask because I do not want to ingest fine rubber particles. Also I wear eye protection against any materials and machine parts that can fly towards my face. Now I wear nitrile gloves for all the processes including packing. All reseal-able plastic bags are wiped over with isopropanol. Kind regards, williams-sonics

EARLY MOTOR SUSPENSION FOR SUGDEN CONNOISSEUR TURNTABLES Fits: ALL EARLY BD-1, BD-2-& BD2A. Cut Band Suspension for ALL EARLY BD1, BD2, BD2A. Motors. This is a very effective suspension that will fit all early motors regardless of the anti-reverse mechanisms position on your motor. This rubber is a soft natural rubber with the perfect properties and excellent resistance to oxidisation, meaning it will last. The quality and performance of suspensions made using this rubber are excellent because of the rubbers natural elasticity. I have a very limited amount of this special natural rubber with no way of obtaining further supply. Nevertheless, I am pleased to be able to offer this kit while I can for all early motors on Connoisseur BD1 & BD2 turntables. These kits are already in use by owners not able to use my web based Conversion kit. This suspension is a Cut Band Suspension, featuring an easy mounting system. It comes as an all hand-made kit which includes the following: Three natural rubber hand cut suspension bands.Six adjustable fixings for the cut bands.One williams-sonics Gold Glass drive belt matched to the cut band suspension.Three natural rubber counter tension bands (graduated in size).One natural rubber insert for your SAU2 bias weight with alignment tool.Instructions which are easy to follow and produce perfect results.I am available for support with fitting through eBay messages.The plastic suspension plate ( hanger plate) which holds the motor to the metal plinth that have a 30mm hole in the centre need no mod. The ones with 20mm diameter hole will need a small semicircle filling inside opposite the lugs, see drawing in second photo. Please note this is a hand made Cut Band Suspension not a web suspension and is designed for early motors only and will not fit later motors. For later motors see my Service kits. If you would prefer a web suspension for your early motor and your motor has its anti-reverse mechanism at its bottom see my Conversion Suspension kit. Contact me if you have any questions, I aim to provide a prompt response. It is coincidental in this period of crisis that the barriers being employed for health reasons are ones that I already use to protect myself in my workshop and have been using for the past three years. The materials I use have always been initially cleaned with isopropanol alcohol before and at various stages of my work with them. I wear a very effective industrial rubber face mask because I do not want to ingest fine rubber particles. Also I wear eye protection against any materials and machine parts that can fly towards my face. Now I wear nitrile gloves for all the processes including packing. All reseal-able plastic bags are wiped over with isopropanol. Kind regards, williams-sonics

MOTOR SUSPENSION WEB SERVICE KIT PLUS PULLER FOR SUGDEN CONNOISSEUR TURNTABLES Fits: BD1, BD2 & BD2A, WITH LATER MOTORS. This web fits all BD1, BD2 and BD2A decks with the later motors which use the 3 leg nylon clip shown below but which is not included in Kit. A later motor has the anti-reverse mechanism under the motor bottom plate. If yours does not, please look at my Conversion Kit which is specially for early motors. This Service Kit includes: - One New Natural Rubber Suspension Web. - One New Gold Class Neoprene Rubber Drive Belt. - Four New Natural Rubber sized Motor Counter Tension Bands.- One New Natural Rubber Insert for the Bias Weight.- One Vial of Platter Spindle Oil with Pipette. - One Puller to remove and adjust the pulley.- Comprehensive Downloadable Fitting Guide. - Contactable for advice on fitting of the Service Kit.The new motor suspension web (or spider as it is sometimes called) is made of highest quality natural new rubber which gives excellent performance. All parts of the Service kit are individually hand-made on receipt of order, then fitted and rigorously tested for performance before shipping to you. This is a Hand-made MATCHED Service Kit designed to work together for Superb Performance. SUSPENSION WEBThe Suspension Web achieves: 1. Superior Performance to any other method of suspending your motor. 2. Natural New Rubber selected for its elasticity and ability to be extremely long lasting. 3. Excellent isolation of the motor, preventing its vibrations from reaching the platter and tonearm. GOLD CLASS DRIVE BELT Williams-Sonics Gold Class Neoprene drive belt is designed and matched with the web to give superb performance.MOTOR TENSION BANDS This essential replacement Service Kit comes with quality hand-made natural rubber bands of the same material to counter the pull of the belt and keep the pulley level. You might only need one but I include a choice of four different sized bands to make it easy to find the correct counter tension for the belt on your model. BIAS WEIGHT RUBBER INSERT As stated above a small natural rubber insert for the bias weight is also part of the SERVICE KIT. This will keep the weight tight and stable on your SAU2 tonearms bias wand. This carefully designed little rubber insert can also make a big difference to your sound quality compared to a loose vibrating bias weight on your tonearm.PLATTER SPINDLE OIL PLUS PIPETTE.A vial of platter spindle oil which has proven to maintain the spindle bearing of these decks in original condition over many years. There is enough oil for many oil changes and it comes with a pipette for administering it accurately and cleanly. FITTING GUIDE An easy to follow fully illustrated online fitting guide comes with each kit. I am also contactable through eBay messages as stated above for support and advice on fitting. MOTOR PULLEY REMOVER Hand-crafted by Williams-Sonics, my Puller enables easy and safe removal of pulleys from Connoisseur BD1 and BD2 turntable motors. It will remove them quickly and safely even if they are seized on through being very tight on the motor spindle or from not being moved for many years. Removing the pulleys by hand is possible but there is the real risk that you will irrevocably damage the motors performance. The slightest bend to the spindle will take the motor out of true alignment and the effect will be heard. Unfortunately, I have encountered several motors damaged in this way. It is impossible to repair such damage. I always use a removal tool as it is just not worth risking hand pulling when replacement motors are not available on these vintage turntables. An equally important use of this removal tool is in adjusting the refitted pulley. Connoisseur pulleys have to be aligned, often by very small amounts. Again we are risking this vintage motor and pulley by pushing the pulley too low, then too high, then too low again in an attempt to find the right place for perfect running at both 33 and 45 rpm. This adjustment is made easy and enjoyable when it is simple to move the pulley by micro amounts using the Puller to precisely tune your turntables drive system. Included with the tool is a short stainless steel tube which can be placed over the motor spindle where the spindle protrudes very high above the pulley. The tool then fits into this tube making it simple to keep both aligned until the spindle is driven flush with the pulley. The puller is supplied with important advice gained from many years of experience with these motors and pulleys. Only Genuine williams-sonics webs and kits are available through williams-sonics. Supplying worldwide to those who demand high fidelity and audiophile performance for their vinyl listening.Contact me if you have any questions, I aim to provide a prompt response. It is coincidental in this period of crisis that the barriers being employed for health reasons are ones that I already use to protect myself in my workshop and have been using for the past two years. The materials I use have always been initially cleaned with isopropanol alcohol before and at various stages of my work with them. I wear a very effective industrial rubber face mask because I do not want to ingest fine rubber particles. Also I wear eye protection against any materials and machine parts that can fly towards my face. Now I wear nitrile gloves for all the processes including packing. All reseal-able plastic bags are wiped over with isopropanol.Kind regards,williams-sonics

MOTOR SUSPENSION WEB SERVICE KIT PLUS PULLER FOR SUGDEN CONNOISSEUR TURNTABLES Fits: BD1, BD2 & BD2A, WITH LATER MOTORS. This web fits all BD1, BD2 and BD2A decks with the later motors which use the 3 leg nylon clip shown below but which is not included in Kit. A later motor has the anti-reverse mechanism under the motor bottom plate. If yours does not, please look at my Conversion Kit which is specially for early motors. This Service Kit includes: - One New Natural Rubber Suspension Web. - One New Gold Class Neoprene Rubber Drive Belt. - Four New Natural Rubber sized Motor Counter Tension Bands.- One New Natural Rubber Insert for the Bias Weight.- One Vial of Platter Spindle Oil with Pipette. - One Puller to remove and adjust the pulley.- Comprehensive Downloadable Fitting Guide. - Contactable for advice on fitting of the Service Kit.The new motor suspension web (or spider as it is sometimes called) is made of highest quality natural new rubber which gives excellent performance. All parts of the Service kit are individually hand-made on receipt of order, then fitted and rigorously tested for performance before shipping to you. This is a Hand-made MATCHED Service Kit designed to work together for Superb Performance. SUSPENSION WEBThe Suspension Web achieves: 1. Superior Performance to any other method of suspending your motor. 2. Natural New Rubber selected for its elasticity and ability to be extremely long lasting. 3. Excellent isolation of the motor, preventing its vibrations from reaching the platter and tonearm. GOLD CLASS DRIVE BELT Williams-Sonics Gold Class Neoprene drive belt is designed and matched with the web to give superb performance.MOTOR TENSION BANDS This essential replacement Service Kit comes with quality hand-made natural rubber bands of the same material to counter the pull of the belt and keep the pulley level. You might only need one but I include a choice of four different sized bands to make it easy to find the correct counter tension for the belt on your model. BIAS WEIGHT RUBBER INSERT As stated above a small natural rubber insert for the bias weight is also part of the SERVICE KIT. This will keep the weight tight and stable on your SAU2 tonearms bias wand. This carefully designed little rubber insert can also make a big difference to your sound quality compared to a loose vibrating bias weight on your tonearm.PLATTER SPINDLE OIL PLUS PIPETTE.A vial of platter spindle oil which has proven to maintain the spindle bearing of these decks in original condition over many years. There is enough oil for many oil changes and it comes with a pipette for administering it accurately and cleanly. FITTING GUIDE An easy to follow fully illustrated online fitting guide comes with each kit. I am also contactable through eBay messages as stated above for support and advice on fitting. MOTOR PULLEY REMOVER Hand-crafted by Williams-Sonics, my Puller enables easy and safe removal of pulleys from Connoisseur BD1 and BD2 turntable motors. It will remove them quickly and safely even if they are seized on through being very tight on the motor spindle or from not being moved for many years. Removing the pulleys by hand is possible but there is the real risk that you will irrevocably damage the motors performance. The slightest bend to the spindle will take the motor out of true alignment and the effect will be heard. Unfortunately, I have encountered several motors damaged in this way. It is impossible to repair such damage. I always use a removal tool as it is just not worth risking hand pulling when replacement motors are not available on these vintage turntables. An equally important use of this removal tool is in adjusting the refitted pulley. Connoisseur pulleys have to be aligned, often by very small amounts. Again we are risking this vintage motor and pulley by pushing the pulley too low, then too high, then too low again in an attempt to find the right place for perfect running at both 33 and 45 rpm. This adjustment is made easy and enjoyable when it is simple to move the pulley by micro amounts using the Puller to precisely tune your turntables drive system. Included with the tool is a short stainless steel tube which can be placed over the motor spindle where the spindle protrudes very high above the pulley. The tool then fits into this tube making it simple to keep both aligned until the spindle is driven flush with the pulley. The puller is supplied with important advice gained from many years of experience with these motors and pulleys. Only Genuine williams-sonics webs and kits are available through williams-sonics. Supplying worldwide to those who demand high fidelity and audiophile performance for their vinyl listening.Contact me if you have any questions, I aim to provide a prompt response. It is coincidental in this period of crisis that the barriers being employed for health reasons are ones that I already use to protect myself in my workshop and have been using for the past two years. The materials I use have always been initially cleaned with isopropanol alcohol before and at various stages of my work with them. I wear a very effective industrial rubber face mask because I do not want to ingest fine rubber particles. Also I wear eye protection against any materials and machine parts that can fly towards my face. Now I wear nitrile gloves for all the processes including packing. All reseal-able plastic bags are wiped over with isopropanol.Kind regards,williams-sonics

MOTOR SUSPENSION WEB AND GOLD CLASS DRIVE BELT SERVICE KIT FOR SUGDEN CONNOISSEUR TURNTABLES Fits: BD1, BD2 & BD2A, WITH LATER MOTORS. This suspension web kit fits all BD1, BD2 and BD2A decks with the later motors which use the 3 leg nylon clip shown below (these clips are not included in the Kit). For early turntable motors please see my other Kits. This Service Kit includes: - One New Natural Rubber Suspension Web. - One New Gold Class Neoprene Rubber Drive Belt. - Four New Natural Rubber sized Motor Counter Tension Bands.- One New Natural Rubber Insert for the Bias Weight.- One Vial of Platter Spindle Oil with Pipette. - Comprehensive Downloadable Fitting Guide. - Contactable for advice on fitting of the Service Kit.The new motor suspension web (or spider as it is sometimes called) is made of highest quality natural new rubber which gives excellent performance. All parts of the Service kit are individually hand-made by myself on receipt of order, then fitted and rigorously tested for performance before shipping to you. This is a Hand-made MATCHED Service Kit designed to work together for Superb Performance. SUSPENSION WEBThe Suspension Web achieves: 1. Superior Performance to any other method of suspending your motor. 2. Natural New Rubber selected for its elasticity and ability to be extremely long lasting. 3. Excellent isolation of the motor, preventing its vibrations from reaching the platter and tonearm. GOLD CLASS DRIVE BELT Williams-Sonics Gold Class Neoprene drive belt is designed and matched with the web to give superb performance.MOTOR TENSION BANDS This essential replacement Service Kit comes with quality hand-made natural rubber bands of the same material to counter the pull of the belt and keep the pulley level. You might only need one but I include a choice of four different sized bands to make it easy to find the correct counter tension for the belt on your model. BIAS WEIGHT RUBBER INSERT As stated above a small natural rubber insert for the bias weight is also part of the SERVICE KIT. This will keep the weight tight and stable on your SAU2 tonearms bias wand. This carefully designed little rubber insert can also make a big difference to your sound quality compared to a loose vibrating bias weight on your tonearm.PLATTER SPINDLE OIL PLUS PIPETTE.A vial of platter spindle oil which has proven to maintain the spindle bearing of these decks in original condition over many years. There is enough oil for many oil changes and it comes with a pipette for administering it accurately and cleanly. FITTING GUIDE An easy to follow fully illustrated online fitting guide comes with each kit. I am also contactable through eBay messages as stated above for support and advice on fitting. Only Genuine williams-sonics webs and kits are available through williams-sonics. Supplying worldwide to those who demand high fidelity and audiophile performance for their vinyl listening. Contact me if you have any questions, I aim to provide a prompt response. It is coincidental in this period of crisis that the barriers being employed for health reasons are ones that I already use to protect myself in my workshop and have been using for the past two years. The materials I use have always been initially cleaned with isopropanol alcohol before and at various stages of my work with them. I wear a very effective industrial rubber face mask because I do not want to ingest fine rubber particles. Also I wear eye protection against any materials and machine parts that can fly towards my face. Now I wear nitrile gloves for all the processes including packing. All reseal-able plastic bags are wiped over with isopropanol. Kind regards,williams-sonics

MOTOR SUSPENSION CONVERSION KIT FOR SUGDEN CONNOISSEUR TURNTABLES Fits: EARLY BD-1, BD-2, with proviso below. The Conversion Kit converts elastic band type suspension of suitable motors to a Williams-Sonics Suspension web and Stainless Steel Conversion which is superior to Sugdens design giving exceptional suspension and retention. The kit is composed of the following items: One Natural Rubber Suspension WebOne Gold Class Neoprene Rubber Drive BeltFour Natural Rubber Counter Tension BandsOne Natural Rubber Insert for the Bias Weight.One A2 Stainless Steel Drilled and Threaded Conversion Plate.Six Nylon Screws and WashersOne tube of thread lockOne vial of Platter Spindle OilOne pipetteDownloadable fitting guideContactable for Advice for fitting of the Conversion Kit. Motors Not Included. If you have an early motor with the anti-reverse mechanism under the top plate, this kit will not fit. Compare your motor to the images below. The kit will fit the suitable motors on the left, but it wont fit the not suitable motors on the right. Please note your motor must have both the empty hole and the high collar of the suitable motors for it to fit. The three holes have already had there little cross bars removed. SUSPENSION WEB and RETAINING PLATE. This is a new williams-sonics motor suspension web with exceptional performance made to exacting standards in quality natural new rubber. Each kit is individually hand-made by myself, the suspension and drive belt are matched to ensure perfect performance before shipping to you. 1. A dependable and exceptional suspension. 2. Perfect motor placement and stability. 3. Excellent isolation of the motor, preventing its vibrations from reaching the platter and tonearm 4 This drilled, tapped and polished stainless steel retaining plate is a far superior design to Sugdens flimsy retaining clip. My retaining plate is made from hard A2 stainless steel. It is not magnetic and will not affect the magnets in the motor. Being stainless steel it will not rust. Nylon is used for screws so they are safe to have below the motor top plate. I looks good too highly polished. GOLD CLASS DRIVE BELT Williams-Sonics Gold Class Neoprene drive belt is designed and Matched with the web to give superb performance. TENSION BANDS The kit comes with quality hand-made rubber bands of the same material to counter the pull of the belt and keep the pulley level. I include a choice of four different sized bands to make it easy to find the correct tension for your belt. BIAS WEIGHT A small natural rubber insert for the bias weight is also part of the Conversion kit. This will keep the weight tight and stable on your SAU2 tonearms bias wand. This carefully designed little rubber insert can also make a big difference to your sound quality compared to a loose vibrating bias weight on your tonearm. PLATTER SPINDLE OIL PLUS PIPETTE.A vial of platter spindle oil which has proven to maintain the spindle bearing of these decks in original condition over many years. There is enough oil for many oil changes and it comes with a pipette for administering it accurately and cleanly. The Conversion Kit comes with an easy to follow fully illustrated fitting guide, online link sent after purchase. Only Genuine williams-sonics webs and kits are available through williams-sonics. Supplying worldwide to those who demand high fidelity and audiophile performancePlease be aware the upgrade is not reversible. Contact me if you have any questions, I aim to provide a prompt response. It is coincidental in this period of crisis that the barriers being employed for health reasons are ones that I already use to protect myself in my workshop and have been using for the past two years. The materials I use have always been initially cleaned with isopropanol alcohol before and at various stages of my work with them. I wear a very effective industrial rubber face mask because I do not want to ingest fine rubber particles. Also I wear eye protection against any materials and machine parts that can fly towards my face. Now I wear nitrile gloves for all the processes including packing. All reseal-able plastic bags are wiped over with isopropanol. Kind regards,williams-sonics

MOTOR SUSPENSION WEB AND GOLD CLASS DRIVE BELT SERVICE KIT FOR SUGDEN CONNOISSEUR TURNTABLES Fits: BD1, BD2 & BD2A, WITH LATER MOTORS. This suspension web kit fits all BD1, BD2 and BD2A decks with the later motors which use the 3 leg nylon clip shown below (these clips are not included in the Kit). For early turntable motors please see my other Kits. This Service Kit includes: - One New Natural Rubber Suspension Web. - One New Gold Class Neoprene Rubber Drive Belt. - Four New Natural Rubber sized Motor Counter Tension Bands.- One New Natural Rubber Insert for the Bias Weight.- One Vial of Platter Spindle Oil with Pipette. - Comprehensive Downloadable Fitting Guide. - Contactable for advice on fitting of the Service Kit.The new motor suspension web (or spider as it is sometimes called) is made of highest quality natural new rubber which gives excellent performance. All parts of the Service kit are individually hand-made on receipt of order, then fitted and rigorously tested for performance before shipping to you. This is a Hand-made MATCHED Service Kit designed to work together for Superb Performance. SUSPENSION WEBThe Suspension Web achieves: 1. Superior Performance to any other method of suspending your motor. 2. Natural New Rubber selected for its elasticity and ability to be extremely long lasting. 3. Excellent isolation of the motor, preventing its vibrations from reaching the platter and tonearm. GOLD CLASS DRIVE BELT Williams-Sonics Gold Class Neoprene drive belt is designed and matched with the web to give superb performance.MOTOR TENSION BANDS This essential replacement Service Kit comes with quality hand-made natural rubber bands of the same material to counter the pull of the belt and keep the pulley level. You might only need one but I include a choice of four different sized bands to make it easy to find the correct counter tension for the belt on your model. BIAS WEIGHT RUBBER INSERT As stated above a small natural rubber insert for the bias weight is also part of the SERVICE KIT. This will keep the weight tight and stable on your SAU2 tonearms bias wand. This carefully designed little rubber insert can also make a big difference to your sound quality compared to a loose vibrating bias weight on your tonearm.PLATTER SPINDLE OIL PLUS PIPETTE.A vial of platter spindle oil which has proven to maintain the spindle bearing of these decks in original condition over many years. There is enough oil for many oil changes and it comes with a pipette for administering it accurately and cleanly. FITTING GUIDE An easy to follow fully illustrated online fitting guide comes with each kit. I am also contactable through eBay messages as stated above for support and advice on fitting. Only Genuine williams-sonics webs and kits are available through williams-sonics. Supplying worldwide to those who demand high fidelity and audiophile performance for their vinyl listening. Contact me if you have any questions, I aim to provide a prompt response. It is coincidental in this period of crisis that the barriers being employed for health reasons are ones that I already use to protect myself in my workshop and have been using for the past two years. The materials I use have always been initially cleaned with isopropanol alcohol before and at various stages of my work with them. I wear a very effective industrial rubber face mask because I do not want to ingest fine rubber particles. Also I wear eye protection against any materials and machine parts that can fly towards my face. Now I wear nitrile gloves for all the processes including packing. All reseal-able plastic bags are wiped over with isopropanol. Kind regards,williams-sonics

MOTOR SUSPENSION WEB SERVICE KIT PLUS PULLER FOR SUGDEN CONNOISSEUR TURNTABLES Fits: BD1, BD2 & BD2A, WITH LATER MOTORS. This web fits all BD1, BD2 and BD2A decks with the later motors which use the 3 leg nylon clip shown below but which is not included in Kit. A later motor has the anti-reverse mechanism under the motor bottom plate. If yours does not, please look at my Conversion Kit which is specially for early motors. This Service Kit includes: - One New Natural Rubber Suspension Web. - One New Gold Class Neoprene Rubber Drive Belt. - Four New Natural Rubber sized Motor Counter Tension Bands.- One New Natural Rubber Insert for the Bias Weight.- One Vial of Platter Spindle Oil with Pipette. - One Puller to remove and adjust the pulley.- Comprehensive Downloadable Fitting Guide. - Contactable for advice on fitting of the Service Kit.The new motor suspension web (or spider as it is sometimes called) is made of highest quality natural new rubber which gives excellent performance. All parts of the Service kit are individually hand-made on receipt of order, then fitted and rigorously tested for performance before shipping to you. This is a Hand-made MATCHED Service Kit designed to work together for Superb Performance. SUSPENSION WEBThe Suspension Web achieves: 1. Superior Performance to any other method of suspending your motor. 2. Natural New Rubber selected for its elasticity and ability to be extremely long lasting. 3. Excellent isolation of the motor, preventing its vibrations from reaching the platter and tonearm. GOLD CLASS DRIVE BELT Williams-Sonics Gold Class Neoprene drive belt is designed and matched with the web to give superb performance.MOTOR TENSION BANDS This essential replacement Service Kit comes with quality hand-made natural rubber bands of the same material to counter the pull of the belt and keep the pulley level. You might only need one but I include a choice of four different sized bands to make it easy to find the correct counter tension for the belt on your model. BIAS WEIGHT RUBBER INSERT As stated above a small natural rubber insert for the bias weight is also part of the SERVICE KIT. This will keep the weight tight and stable on your SAU2 tonearms bias wand. This carefully designed little rubber insert can also make a big difference to your sound quality compared to a loose vibrating bias weight on your tonearm.PLATTER SPINDLE OIL PLUS PIPETTE.A vial of platter spindle oil which has proven to maintain the spindle bearing of these decks in original condition over many years. There is enough oil for many oil changes and it comes with a pipette for administering it accurately and cleanly. FITTING GUIDE An easy to follow fully illustrated online fitting guide comes with each kit. I am also contactable through eBay messages as stated above for support and advice on fitting. MOTOR PULLEY REMOVER Hand-crafted by Williams-Sonics, my Puller enables easy and safe removal of pulleys from Connoisseur BD1 and BD2 turntable motors. It will remove them quickly and safely even if they are seized on through being very tight on the motor spindle or from not being moved for many years. Removing the pulleys by hand is possible but there is the real risk that you will irrevocably damage the motors performance. The slightest bend to the spindle will take the motor out of true alignment and the effect will be heard. Unfortunately, I have encountered several motors damaged in this way. It is impossible to repair such damage. I always use a removal tool as it is just not worth risking hand pulling when replacement motors are not available on these vintage turntables. An equally important use of this removal tool is in adjusting the refitted pulley. Connoisseur pulleys have to be aligned, often by very small amounts. Again we are risking this vintage motor and pulley by pushing the pulley too low, then too high, then too low again in an attempt to find the right place for perfect running at both 33 and 45 rpm. This adjustment is made easy and enjoyable when it is simple to move the pulley by micro amounts using the Puller to precisely tune your turntables drive system. Included with the tool is a short stainless steel tube which can be placed over the motor spindle where the spindle protrudes very high above the pulley. The tool then fits into this tube making it simple to keep both aligned until the spindle is driven flush with the pulley. The puller is supplied with important advice gained from many years of experience with these motors and pulleys. Only Genuine williams-sonics webs and kits are available through williams-sonics. Supplying worldwide to those who demand high fidelity and audiophile performance for their vinyl listening.Contact me if you have any questions, I aim to provide a prompt response. It is coincidental in this period of crisis that the barriers being employed for health reasons are ones that I already use to protect myself in my workshop and have been using for the past two years. The materials I use have always been initially cleaned with isopropanol alcohol before and at various stages of my work with them. I wear a very effective industrial rubber face mask because I do not want to ingest fine rubber particles. Also I wear eye protection against any materials and machine parts that can fly towards my face. Now I wear nitrile gloves for all the processes including packing. All reseal-able plastic bags are wiped over with isopropanol.Kind regards,williams-sonics

MOTOR SUSPENSION CONVERSION KIT FOR SUGDEN CONNOISSEUR TURNTABLES Fits: EARLY BD-1, BD-2, with proviso below. The Conversion Kit converts elastic band type suspension of suitable motors to a Williams-Sonics Suspension web and Stainless Steel Conversion which is superior to Sugdens design giving exceptional suspension and retention. The kit is composed of the following items: One Natural Rubber Suspension WebOne Gold Class Neoprene Rubber Drive BeltFour Natural Rubber Counter Tension BandsOne Natural Rubber Insert for the Bias Weight.One A2 Stainless Steel Drilled and Threaded Conversion Plate.Six Nylon Screws and WashersOne tube of thread lockOne vial of Platter Spindle OilOne pipetteDownloadable fitting guideContactable for Advice for fitting of the Conversion Kit. Motors Not Included. If you have an early motor with the anti-reverse mechanism under the top plate, this kit will not fit. Compare your motor to the images below. The kit will fit the suitable motors on the left, but it wont fit the not suitable motors on the right. Please note your motor must have both the empty hole and the high collar of the suitable motors for it to fit. The three holes have already had there little cross bars removed. SUSPENSION WEB and RETAINING PLATE. This is a new williams-sonics motor suspension web with exceptional performance made to exacting standards in quality natural new rubber. Each Kit is individually hand-made on receipt of order, then fitted and tested for performance before shipping to you. 1. A dependable and exceptional suspension. 2. Perfect motor placement and stability. 3. Excellent isolation of the motor, preventing its vibrations from reaching the platter and tonearm 4 This drilled, tapped and polished stainless steel retaining plate is a far superior design to Sugdens flimsy retaining clip.My retaining plate is made from hard A2 stainless steel. It is not magnetic and will not affect the magnets in the motor. Being stainless steel it will not rust. Nylon is used for screws so they are safe to have below the motor top plate. I looks good too highly polished. GOLD CLASS DRIVE BELT Williams-Sonics Gold Class Neoprene drive belt is designed and matched with the web to give superb performance. TENSION BANDS The kit comes with quality hand-made rubber bands of the same material to counter the pull of the belt and keep the pulley level. I include a choice of four different sized bands to make it easy to find the correct tension for your belt. BIAS WEIGHT A small natural rubber insert for the bias weight is also part of the Conversion kit. This will keep the weight tight and stable on your SAU2 tonearms bias wand. This carefully designed little rubber insert can also make a big difference to your sound quality compared to a loose vibrating bias weight on your tonearm. PLATTER SPINDLE OIL PLUS PIPETTE.A vial of platter spindle oil which has proven to maintain the spindle bearing of these decks in original condition over many years. There is enough oil for many oil changes and it comes with a pipette for administering it accurately and cleanly. The Conversion Kit comes with an easy to follow fully illustrated fitting guide, online link sent after purchase. Only Genuine williams-sonics webs and kits are available through williams-sonics. Supplying worldwide to those who demand high fidelity and audiophile performancePlease be aware the upgrade is not reversible. Contact me if you have any questions, I aim to provide a prompt response. It is coincidental in this period of crisis that the barriers being employed for health reasons are ones that I already use to protect myself in my workshop and have been using for the past two years. The materials I use have always been initially cleaned with isopropanol alcohol before and at various stages of my work with them. I wear a very effective industrial rubber face mask because I do not want to ingest fine rubber particles. Also I wear eye protection against any materials and machine parts that can fly towards my face. Now I wear nitrile gloves for all the processes including packing. All reseal-able plastic bags are wiped over with isopropanol. Kind regards,williams-sonics

.AR Sugden Connoisseur BD1 /BD2 Turntable spares in used order-BRAKE ON/OFF LEVER/TONEARMWEIGHT AND DRIVE BELT ALL TAKEN FROM A WORKING TURNTABLE 9 YEARS AGO.NO TURNTABLE ONLY SPARES AS IN PICTURE.thanks for looking-UK BIDDERS ONLY AND NO BUY IT NOW.will not ship to shipping companies or alternative addresses.please text on 07933158535 any questions

Turntable motor for Sugden Connoisseur BD 1, BD2 record decks . Taken from a damaged deck. Tested and working.

.AR Sugden Connoisseur BD1 /BD2 Turntable spares in used order-BRAKE ON/OFF LEVER/TONEARMWEIGHT AND DRIVE BELT ALL TAKEN FROM A WORKING TURNTABLE 9 YEARS AGO.NO TURNTABLE ONLY SPARES AS IN PICTURE.thanks for looking-UK BIDDERS ONLY AND NO BUY IT NOW.will not ship to shipping companies or alternative addresses.please text on 07933158535 any questions