Selling 1 of &W Bowers Wilkins Foam Plug Bung for 702 s2, 804 D3, CM10 Speaker

I am a B&W, Bowers & Wilkins Hi-Fi Audio Consultant for over 40-years. This TWEETER MOTER has been Repaired. It was accidently pushed In during installation... and Professionally Pushed Back into shape.It is excellent working order. ( What you see in the pictures, is what you will receive. ) Bowers & Wilkins NAUTILUS Tweeter ZC12092, ZZ11770, or ZZ11266 for:B&W N805B&W N804B&W N803B&W N802B&W N801B&W N801B&W NHTM1B&W NHTM2 B&W HTM1B&W HTM2B&W CDM-CNTB&W CDM-1NTB&W CDM-7NTB&W CDM-9NT Shipping & Handling, and Conditions: * Ships only to the 48-states. * No International Sales. * Pay with PayPal Only, must have a Confirmed/ Verified shipping address with PayPal. * Cost of Shipping: $10 ( to the 48-states). * All sales are final, No Refunds. Exclude shipping locationsExclude specific locations (regions, countries, PO boxes) that you dont want to ship to. To save time and list faster, go to My eBay Site Preferences and select the specific locations you want to exclude on allyour listings. Learn moreExcluded locations:Alaska/Hawaii, US Protectorates, APO/FPO, Africa, Asia, Central America and Caribbean, Europe, Middle East, Oceania, Southeast Asia, South America, PO Box

I am a B&W, Bowers & Wilkins Hi-Fi Audio Consultant for over 40-years. This TWEETER MOTER has been Repaired. It was accidently pushed In during installation... and Professionally Pushed Back into shape.It is excellent working order. ( What you see in the pictures, is what you will receive. ) Bowers & Wilkins NAUTILUS Tweeter ZC12092, ZZ11770, or ZZ11266 for:B&W N805B&W N804B&W N803B&W N802B&W N801B&W N801B&W NHTM1B&W NHTM2 B&W HTM1B&W HTM2B&W CDM-CNTB&W CDM-1NTB&W CDM-7NTB&W CDM-9NT Shipping & Handling, and Conditions: * Ships only to the 48-states. * No International Sales. * Pay with PayPal Only, must have a Confirmed/ Verified shipping address with PayPal. * Cost of Shipping: $10 ( to the 48-states). * All sales are final, No Refunds. Exclude shipping locationsExclude specific locations (regions, countries, PO boxes) that you dont want to ship to. To save time and list faster, go to My eBay Site Preferences and select the specific locations you want to exclude on allyour listings. Learn moreExcluded locations:Alaska/Hawaii, US Protectorates, APO/FPO, Africa, Asia, Central America and Caribbean, Europe, Middle East, Oceania, Southeast Asia, South America, PO Box

See Additional Photos, Below. I am a B&W, Bowers & Wilkins Hi-Fi Audio Consultant for over 40-years. This TWEETER MOTER has been Repaired. It was accidently pushed In during installation... and Professionally Pushed Back into shape.It is excellent working order. ( What you see in the pictures, is what you will receive. ) Bowers & Wilkins NAUTILUS Tweeter ZZ11770, or ZZ11266 for:B&W N805B&W N804B&W N803B&W N802B&W N801B&W N801B&W NHTM1B&W NHTM2 B&W HTM1B&W HTM2B&W CDM-CNTB&W CDM-1NTB&W CDM-7NTB&W CDM-9NT Shipping & Handling, and Conditions: * Ships only to the 48-states. * No International Sales. * Pay with PayPal Only, must have a Confirmed/ Verified shipping address with PayPal. * Cost of Shipping: $10 ( to the 48-states). * All sales are final, No Refunds. Exclude shipping locationsExclude specific locations (regions, countries, PO boxes) that you dont want to ship to. To save time and list faster, go to My eBay Site Preferences and select the specific locations you want to exclude on allyour listings. Learn moreExcluded locations:Alaska/Hawaii, US Protectorates, APO/FPO, Africa, Asia, Central America and Caribbean, Europe, Middle East, Oceania, Southeast Asia, South America, PO Box

Abspiel-/Abtastnadel für Dual Plattenspieler, DN 330, 212 804, Original, mind. 20 Jahre alt, unbenutzt, in Originalverpackung

Excellent Ixos reference standard 75Ohm cable tested with the Chord Qutest and DAVE. Ideal for all CHORD DACs such as the Qutest, TT2, and DAVE, tested with Qutest and DAVE during design, each individually tested and burned in using the Qutest before being shipped. Also suitable for Linn, NAIM, Denafrips, Gustard etc with BNC fittings. Pure Crystal oxygen-free copper cable with low density dielectric and true 75 Ohm construction. The BNC plug is a Yarbo, audiophile quality gold plated copper. (Usually the plugs are brass)Assembled by hand in the UK.Digital SPDIF cable to connect CD / digital player or streamer to DAC. 1.5m RCA to BNC is the optimum length for a SPDIF cable. See detail below. Burned in using the Tara Labs Cascade file. Not this is a fully tested used cable, I have cleaned it and cut it from a longer length and fitted the new BNC plug. The yellow cable may have some marks or signs of use. I also sell a New Old Stock version of the cable for a little more money. They sound the same of course! This saves money with no real penalty - any marking on the cable is moonier - you certainly wont notice it at the back of your equipment! Please see the excellent 100% feedback I have received for hundreds of digital and analogue cables. Length of cable – why 1.5m? Summary There are only two occasions in audio where a longer cable – or an optimum length cable is better than a short one. Digital cables have an optimum length of 1.5m or more. (The other occasion is for MM phono cartridges, which need a specific capacitance). The reason for this requires an explanation. Please refer to the diagram in the photos. The signal travelling down a SPDIF (so-called digital cable) is actually a square wave ANALOGUE voltage signal; however, in reality, this square does not have instantaneous changes - the squares are sloped and somewhat rounded off, too, as it takes some time to change state from 0 to 1 or 1 to 0. The accuracy of the pulses at the end of the cable determines how accurately the source can interpret the signal in value 1 or 0 and also timing which is not so easy. The signal reflects back off the ends of the cable, the plugs and connected equipment (echoing back and forth). It produces ghost images of itself, which can fool the receiver into thinking that the ghost signals are the original signals. With short cables, under 1m, the ghost signals arrive close to the originals within the transition time frame from 0 to 1 or 1 to 0 before the transition occurs. A 1m cable means the reflection arrives at about the same time as the transition is to be recorded. With longer cables, the reflection arrives too late to influence the receiver (The transition has already been recorded). Longer cables also mean lower amplitude or signal reflection; thus receiver can more easily determine between the correct signal and the spurious reflections. The bottom line is that a longer cable eliminates the false readings from the ghost images and thus reduces timing errors, called jitter, and therefore sounds better. Measurements and experimentation have determined the optimum size to be 1.5m or more. Very detailed explanation- for the curious, accompanies the diagram in the photos. Why SPDIF cables should be 1.5m long, detailed explanation. When the SPDIF signal is launched into the cable from the Transport, it is essentially a voltage square wave, consisting of rising and falling edges. These edges are no more than voltage transitions from about –250mV to +250mV, the rising edge transitioning from minus voltage to plus voltage and the falling edge transitioning from plus voltage to minus voltage. When an edge transitions, it can be described as having a rise-time or fall-time. This is the time it takes for the signal to transition from 10% to 90% of the entire voltage swing. (Note that this DOES Not happen instantaneously). The rise-time is important because this is what causes reflections on the transmission line. If the rise-time were very, very slow, say 50 nanoseconds, then there would be no reflections on the transmission line unless it was extremely long. Alternately, if the rise-time were less than one nanosecond, reflections would occur at every boundary, such as the connection from the circuit board to the wires that go to the connector. Typical stock Transports have around 25 nanosecond rise times. The primary concern for the manufacturer is to pass FCC regulations for emissions and electromagnetic interference and make the interface reliable. When the regulatory testing is done, they attach inexpensive, inferior cables and measure the emissions. To ensure that the manufacturer passes these tests, they take several precautions. One is designing in the slower than necessary 25 nanosecond rise-time. Another is inserting various filters in the Transport to eliminate high frequencies from the signal. As a result of these choices, there is a hazard created in using too short a digital cable. It is a result of the slow rise-time. When a transition is launched into the cable, it takes a period of time to propagate or transit to the other end. This propagation time is somewhat slower than the speed of light, usually around two nanoseconds per foot, but can be longer depending on the dielectrics used in the digital cable. When the transition reaches the end of the transmission line (in the DAC), a reflection can occur that propagates back to the driver in the Transport. Small reflections can occur in even well-matched systems. When the reflection reaches the driver, it can again be reflected back towards the DAC. This ping-pong effect can sustain itself for several bounces depending on the losses in the cable. It is not unusual to see 3-5 of these reflections before they finally decay away, mainly when using the best digital cables, which are usually low-loss. So, how does this affect the jitter? When the first reflection returns to the DAC, if the transition already in process at the receiver has not been completed, the reflection voltage will superimpose itself on the transition voltage, causing the transition to shift in time. The DAC will sample the transition in this time-shifted state, and there you have jitter. Lets look at a numerical example: If the rise-time is 25 nanoseconds and the cable length is 3 feet, then the propagation time is about 6 nanoseconds. Once the transition has arrived at the receiver, the reflection propagates back to the driver (6 nanoseconds), and then the driver reflects this back to the receiver (6 nanoseconds) = 12 nanoseconds. So, as seen at the receiver, 12 nanoseconds after the 25 nanosecond transition started, we have a reflection superimposing on the transition. This is right about the time that the receiver will try to sample the transition, right around 0 volts DC. Not good. Now, if the cable had been 1.5 meters, the reflection would have arrived 18 nanoseconds after the 25 nanosecond transition started at the receiver. This is much better because the receiver has likely already sampled the transition by this time.Unfortunately, better (usually more expensive) cables produce better digital sound. Blame the people who decided on the digital interface decades ago for not separating audio-only from the need to send audio with moving pictures.

Excellent Ixos reference standard 75Ohm cable tested with the Chord Qutest and DAVE. Ideal for all CHORD DACs such as the Qutest, TT2, and DAVE, tested with Qutest and DAVE during design, each individually tested and burned in using the Qutest before being shipped. Also suitable for Linn, NAIM etc with BNC fittings. Pure Crystal oxygen-free copper cable with low density dielectric and true 75 Ohm construction. The BNC plug is a Yarbo, audiophile quality gold plated copper. (Usually the plugs are brass)Assembled by hand in the UK.Digital SPDIF cable to connect CD / digital player or streamer to DAC. 1.5m RCA to BNC is the optimum length for a SPDIF cable. See detail below. Burned in using the Tara Labs Cascade file. Please see the excellent 100% feedback I have received for hundreds of digital and analogue cables. Length of cable – why 1.5m? Summary There are only two occasions in audio where a longer cable – or an optimum length cable is better than a short one. Digital cables have an optimum length of 1.5m or more. (The other occasion is for MM phono cartridges, which need a specific capacitance). The reason for this requires an explanation. Please refer to the diagram in the photos. The signal travelling down a SPDIF (so-called digital cable) is actually a square wave ANALOGUE voltage signal; however, in reality, this square does not have instantaneous changes - the squares are sloped and somewhat rounded off, too, as it takes some time to change state from 0 to 1 or 1 to 0. The accuracy of the pulses at the end of the cable determines how accurately the source can interpret the signal in value 1 or 0 and also timing which is not so easy. The signal reflects back off the ends of the cable, the plugs and connected equipment (echoing back and forth). It produces ghost images of itself, which can fool the receiver into thinking that the ghost signals are the original signals. With short cables, under 1m, the ghost signals arrive close to the originals within the transition time frame from 0 to 1 or 1 to 0 before the transition occurs. A 1m cable means the reflection arrives at about the same time as the transition is to be recorded. With longer cables, the reflection arrives too late to influence the receiver (The transition has already been recorded). Longer cables also mean lower amplitude or signal reflection; thus receiver can more easily determine between the correct signal and the spurious reflections. The bottom line is that a longer cable eliminates the false readings from the ghost images and thus reduces timing errors, called jitter, and therefore sounds better. Measurements and experimentation have determined the optimum size to be 1.5m or more. Very detailed explanation- for the curious, accompanies the diagram in the photos. Why SPDIF cables should be 1.5m long, detailed explanation. When the SPDIF signal is launched into the cable from the Transport, it is essentially a voltage square wave, consisting of rising and falling edges. These edges are no more than voltage transitions from about –250mV to +250mV, the rising edge transitioning from minus voltage to plus voltage and the falling edge transitioning from plus voltage to minus voltage. When an edge transitions, it can be described as having a rise-time or fall-time. This is the time it takes for the signal to transition from 10% to 90% of the entire voltage swing. (Note that this DOES Not happen instantaneously). The rise-time is important because this is what causes reflections on the transmission line. If the rise-time were very, very slow, say 50 nanoseconds, then there would be no reflections on the transmission line unless it was extremely long. Alternately, if the rise-time were less than one nanosecond, reflections would occur at every boundary, such as the connection from the circuit board to the wires that go to the connector. Typical stock Transports have around 25 nanosecond rise times. The primary concern for the manufacturer is to pass FCC regulations for emissions and electromagnetic interference and make the interface reliable. When the regulatory testing is done, they attach inexpensive, inferior cables and measure the emissions. To ensure that the manufacturer passes these tests, they take several precautions. One is designing in the slower than necessary 25 nanosecond rise-time. Another is inserting various filters in the Transport to eliminate high frequencies from the signal. As a result of these choices, there is a hazard created in using too short a digital cable. It is a result of the slow rise-time. When a transition is launched into the cable, it takes a period of time to propagate or transit to the other end. This propagation time is somewhat slower than the speed of light, usually around two nanoseconds per foot, but can be longer depending on the dielectrics used in the digital cable. When the transition reaches the end of the transmission line (in the DAC), a reflection can occur that propagates back to the driver in the Transport. Small reflections can occur in even well-matched systems. When the reflection reaches the driver, it can again be reflected back towards the DAC. This ping-pong effect can sustain itself for several bounces depending on the losses in the cable. It is not unusual to see 3-5 of these reflections before they finally decay away, mainly when using the best digital cables, which are usually low-loss. So, how does this affect the jitter? When the first reflection returns to the DAC, if the transition already in process at the receiver has not been completed, the reflection voltage will superimpose itself on the transition voltage, causing the transition to shift in time. The DAC will sample the transition in this time-shifted state, and there you have jitter. Lets look at a numerical example: If the rise-time is 25 nanoseconds and the cable length is 3 feet, then the propagation time is about 6 nanoseconds. Once the transition has arrived at the receiver, the reflection propagates back to the driver (6 nanoseconds), and then the driver reflects this back to the receiver (6 nanoseconds) = 12 nanoseconds. So, as seen at the receiver, 12 nanoseconds after the 25 nanosecond transition started, we have a reflection superimposing on the transition. This is right about the time that the receiver will try to sample the transition, right around 0 volts DC. Not good. Now, if the cable had been 1.5 meters, the reflection would have arrived 18 nanoseconds after the 25 nanosecond transition started at the receiver. This is much better because the receiver has likely already sampled the transition by this time.Unfortunately, better (usually more expensive) cables produce better digital sound. Blame the people who decided on the digital interface decades ago for not separating audio-only from the need to send audio with moving pictures.

B&W Nautilus 804 Speakers.

B&W Bowers & Wilkins 804 Matrix part out. Listing (1) ZZ8605 Matrix mid-woofer. Overall excellent condition and fully functional. B&W has long since stopped supporting the older 800 series. These seldom come up for sale, so if you need a replacement, don’t miss out. Even if you don’t currently need one, it’s always a great idea to have a spare.

Studer A80 board 1.080.804.11. Sell as is

Edwards Home Entertainment and Design has this offering a pair of Bowers & Wilkins 804D3 speakers. This is a phenomenal set of Diamond speakers, the 804D3 in good shape, without major issues, grills are in fine shape and factory packaging and boxes are included!! Buy / Sell / Trade / Consign - Edwards Home Entertainment and Design (EHEAD Audio, located in South San Francisco, CA) has been a premier seller of carefully selected, pre-loved high end audio equipment since 1997. In 2020 I became a dealer for several manufacturers - to add to the plethora of great quality, highly sought after, preowned gear.  Now an authorized dealer for Parasound (displaying JC-1+, JC2BP, HINT 6, JC-5, JC-3+), Bowers & Wilkins (displaying 801D4, 802D4, 803D4, 804D4, 805D4, 702S2 Signature Midnight Blue, 705S2 Signature), Classe Delta (displaying the Delta Pre, Delta Stereo, Delta Monos), Focal (displaying Scala EVO, Sopra3, Sopra 2), NAIM (displaying the SuperNAIT3), Rotel Michi (displaying the P5, S5), Fyne Audio (displaying F1-12, 502SP, F700), Marantz (displaying PM-10 Integrated, SA-10 Super Audio SACD/CD Player, TT-15S2 TurnTable), Rel Acoustics (displaying S/812 and S/512), Lumin (displaying T2, D2, and U1 mini), Nordost (displaying Norse and Leif series, with demo cases for in home trials), SolidSteel (displaying HyperSpike and S3 walnut), Finite Element (displaying Pagode).   EHEAD Audio is always looking to buy quality used gear.  Do reach out and we can discuss single to entire systems, to even life long collections that you may be looking to sell.  Every piece of equipment EHEAD Audio provides, operates as expected as each and every piece is inspected, tested, and listened to prior to sale.  After all, I love music as you do and learning what pieces of gear do well and match with others is part of the invaluable experience I provide, and have since 1997.   Despite listings that may indicate LOCAL PICK UP ONLY - this is just to facilitate posting of gear.  Logistics is our specialty, we can facilitate packaging and shipping to and from anywhere in the country.  If you are interested in our gear, please reach out and we can figure out a shipping solution that will work.  EhEAD Audio can facilitate and complete all necessary documentation for the export of your gear purchased from us. Our shop is in South San Francisco - stop by and put your eyes and ears to work! California residents or any shipment within California must pay sales tax.

Bowers & Wilkins 804 D3 white speaker pair - in mint condition. Absolutely mint condition, like new. Fenomanal signagure B&W sound, but I guess I will not need to detail that if you are looking at this advert. All accessories + most of packaging (protective plastic bottom and top from the box is provided but no cardboards) Selling due to relocation to Europe. ( due to this please note that the speakers will only be availbale for sale in the UK untill early/mid June, if unsold by then they are moving with me:))) Collection from Cambridge area but depending on destination I may consider delivering it (or to at least to a certain point) for the coat of fuel.

B&W Nautilus 804 Speakers.

This auction is for one original RCA type 804 pentode tube with large red RCA logo. Good appearance and has good filament - cannot test otherwise so sold as is. Also included is a vintage UX RCA type UR-542 base- is not correct electrically for this tube but it fits into the base collar and makes a nice display base as it is heavy. Plating on socket shell could use some polish but OK otherwise. RCA used this red print logo for a short period of time - mainly on its larger tubes. Nice tube for tube collector- will ship worldwide.

4 Pieces Telefunken EF804S / EF 804 S <> Diamond bottom Tube NOS NIB SEALED Made in Ulm factory West Germany Tubes are new old stock in sealed box, never used. 1 box has been opened to check, see pictures. Auction is for 4 pieces tubes. Worldwide shipping. Please send a message first for exact shipping costs, thank you.

Selling 1 of &W Bowers Wilkins Foam Plug Bung for 702 s2, 804 D3, CM10 Speaker

4 Pieces Telefunken EF804S / EF 804 S <> Diamond bottom Tube NOS NIB SEALED Made in Ulm factory West Germany Tubes are new old stock in sealed box, never used. 1 box has been opened to check, see pictures. Auction is for 4 pieces tubes. Worldwide shipping. Please send a message first for exact shipping costs, thank you.

Sony Ta-F6B Vintage Stereo Verstärker. Das Gerät funktioniert und ist in einem guten Zustand. Nur bieten wer damit einverstanden ist. Bilder sind Bestandteil der Artikelbeschreibung. Lieferumfang siehe Bilder. Die Versandkosten beinhalten zudem das Verpackungsmaterial (bitte beachten). Versandkosten fürs Ausland bitte Nachfragen. Die Ware unterliegt der Differenzbesteuerung nach UStG. §25a, eine Ausweisung der MwSt. ist nicht möglich.

B&W Nautilus 804 Speakers.

B&W Bowers & Wilkins 804 Matrix part out. Listing (1) ZZ8605 Matrix mid-woofer. Overall excellent condition and fully functional. B&W has long since stopped supporting the older 800 series. These seldom come up for sale, so if you need a replacement, don’t miss out. Even if you don’t currently need one, it’s always a great idea to have a spare.

Overture Ultimate Home Electronics, located in Wilmington, Delaware, is America’s premier high-end audio, home theater, and home electronics store. The equipment we are offering on Ebay is either equipment we have had on demo at Overture, or equipment that has been taken in by Overture as a trade-in from our customers. All of the equipment has been thoroughly checked by our technicians to make sure it works properly. BEFORE YOU BID SEE IF YOUR STATE IS ON THE TAX LIST. EBAY IS NOW CHARGING TAX.Up for auction is a pair of B&W 804 D3 Loudspeakers, used, as trade ins to our showroom. Minor blemish on the backside of one of the speakers. They come with spikes, jumpers, manuals, packaging, and boxes. Shipped Freight or Local Pickup.

Ikea SYMFONISK Sonos Wi-Fi Bookshelf /Table Speaker WHITE 804.352.11 New in Box!Guaranteed Authentic and Brand NewLike all our items, we guarantee that this item is Brand New, 100% Genuine and from a legitimate source!Customer ServiceWe have been online sellers for 10 years and strive to provide exceptional Customer Service. If you have any questions or concerns – before or after your order - please reach out to us and we will always address your concerns. Condition Item: Brand New, perfect. Has been tested to ensure perfect functioningPackaging: Original Ikea packaging. NOTE: Possible markings / stickers on packaging **Please review the pictures, as they represent the actual item & packaging condition**NOTE Please be sure to read the description thoroughly to make sure that this is the item you want before ordering. If you have any questions about this item or are unsure about anything in this listing, please contact us via eBay messages BEFORE placing your order. We make every effort possible to accurately describe and depict the items. Please be aware that slight variations in color may be due to differences in lighting and computer monitor resolutionsIncluded:Speaker as picturedNOT Included:Brackets / anything not mentioned USA Shipping:Free anywhere in the continental USA via USPS or UPS Ground (2-5 business days)Ships from Niagara Falls, NY 14304Ships within 1-3 business days of receiving cleared payment.Need it faster? Please message us before ordering & we will try to assistDescription:Sales Tax:State and/or local sales taxes may be collected by eBay if applicable in your area. No other taxes or fees are applicable to this itemReturns/ Replacements:Defective / Incorrect Item: Defects / errors are rare, but we always look after our Buyers. Within 30 days of receiving your item, we will accept a return and/or replace a defective or incorrect item, all at our expense. Proof of the defect (pictures) may be required, as per eBay policy.Other Reasons: Within 30 days of receiving your item, we will accept a return for other reasons. Item must be fully intact, in the same condition & packaging as shipped to you. Return shipping is at your expense. A restocking fee of up to 20% (as per eBay policy) may apply. Photos of the item showing its current condition required.Important: Item listed is unique to the brand noted and will not work with any other brand, even if the specifications appear similarWarranty: We are not authorized sellers of this item. As this is a private sale, no warranty (expressed or implied) is offered, other than what the manufacturer provides for eBay sales, if any.Intellectual Property (IP): Brand names & some item descriptions shown / mentioned in this listing are for description purposes only and are the property of the Brand owner. We are not authorized sellers of this item.