Denon DRA 400 Precision Audio Component AM/FM Tuner Stereo AMP Receiver Used, works - Bought at an estate sale, history unknown Tape Deck Not Included Video available of working FM and Cassette under extra kart parts youtube channel - message for link Below description found online and buyer must confirm accuracy- reference only - Info from gamma electronics - XYZ Manufacturers Specifications FM Tuner Section: Usable Mono Sensitivity: 10.3 dBf. S/N Ratio: Mono, 75 dB; stereo, 72 dB. THD at 1 kHz: Mono, 0.1%; stereo, 0.2%. Capture Ratio: 1.2 dB. Image Rejection: 45 dB. AM Suppression: 60 dB. Stereo Separation, 1 kHz: 50 dB. Frequency Response: 10 Hz to 15 kHz, +0.2,-1.5 dB. AM Tuner Section: Usable Sensitivity: 15 dB. S/N Ratio: 55 dB. Amplifier Section: Power Output: 40 watts per channel, 8 ohms, 20 Hz to 20 kHz (50 watts, 1 kHz, 4 ohms). THD: 0.02%, 8 ohms. Damping Factor: 80, 1 kHz, 8 ohms. Input Sensitivity: MM phono, 2.5 mV; MC phono, 0.25 mV; high level, 150 mV. Maximum Phono Input Level: MM phono, 200 mV; MC phono, 20 mV. Frequency Response: Phono, RIAA 0.5 dB; high level, 20 Hz to 20 kHz, 0.5 dB. S/N Ratio: MM phono, 80 dB; MC phono, 62 dB; high level, 96 dB. Tone Control Range: 10 dB at 50 Hz and 10 kHz. Subsonic Filter Cutoff: 18 Hz, 6 dB per octave. General Specifications: Power Consumption: 130 watts. Dimensions: 17.1 in. (43.4 cm) W x 4.4 in. (11.2 cm) H x 16.1 in. (40.8 cm) D. Weight: 19.8 lbs. (9.0 kg). Price: $399.95. Company Address: 61 Law Dr., Fairfield, N.J. 07006. As so often happens with advances in audio technology, new features are first incorporated in top-of-the-line separate components which are beyond the reach of all but the most affluent of audio enthusiasts. Later on, these features filter down to high-powered, high-priced all-in-one receiv ers, where a larger audience is potentially available. Finally, they are incorporated into relatively low-cost, medium-powered receivers that just about anyone interested in good sound can afford. The Denon DRA-400 is a good example of a receiver which has benefited from technology first found in higher priced units. This receiver employs crystal-controlled, frequency-synthesized tuning for accuracy and has a five-station preset capability with battery-operated memory backup. Not only does the phono preamplifier section incorporate both moving-magnet and moving-coil inputs (the latter at an input impedance of 100 ohms), but the phono preamp-equalizer section has a direct-coupled input. The power amplifier section employs a non-switching biasing circuit for the elimination of so-called switching and notch distortion at the output stages. These refinements would have been found only on more expensive components just a few years ago. The front panel of the Denon DRA-400 is neatly divided into highly functional upper and lower sections. The upper section contains the power on/off switch, a numeric display of station frequency, a stereo indicator light, a signal-strength LED indicator, up and down tuning buttons, the five preset buttons and their memory switch, program selector pushbuttons, and a large, rotary master-volume control. The signal-strength indicator takes the form of a go-no-go indicator, rather than a signal-strength meter: It lights when the incoming signal strength is deemed adequate and does not light when weaker signals are received-an interesting approach but not very useful. Controls in the lower section are normally covered by a swing-down hinged door, since they are used less frequently than those just described. Behind the door panel are a stereo headphone jack; a pair of speaker selector buttons; bass, treble and balance controls; a three-position monitor/ copy switch; a subsonic filter switch; a stereo/mono switch (associated with FM reception); an MM/MC phono switch, and a loudness on/off switch. The rear panel of the DRA-400 is equipped with the usual 75- and 300-ohm FM antenna terminals, phono and high level input terminals, two pairs of tape in/out jacks, two pairs of color-coded speaker connection terminals, a chassis ground terminal, and a pair of a.c. convenience outlets (one switched, one unswitched). Instead of the usual AM loop stick antenna, a more elaborate, true AM loop antenna is packed with the receiver as a separate item; its two leads must be connected to the appropriate AM and ground terminals on the back of the set. The pivotable loop antenna is best snapped into an antenna holder during receiver installation so the antenna can still be rotated for best AM reception. Since this loop antenna forms part of the input-stage tuned circuit, the owners manual suggests that even if an outdoor AM antenna is used (because of inadequate signal strength), the loop antennas leads should remain connected to their appropriate terminals, in parallel with the outdoor antenna leads. Tuner Measurements Usable mono FM sensitivity fell short of published claims, measuring 16 dBf (3.47 V across 300 ohms). In stereo, sensitivity was limited by muting and stereo thresholds, which were set to 32 dBf (21.9 V). For 50-dB quieting in mono, an input signal strength of 19.5 dBf (5.2 V) was required; for stereo, a signal strength of 42 dBf (69.2 V) was needed. Plots of quieting and distortion (at 1 kHz) versus signal strength are shown in Fig. 1. Signal-to-noise in mono, at 65 dBf of input signal, measured 75 dB as claimed; in stereo it was 72 dB, also exactly as claimed. Harmonic distortion in mono measured 0.17% for a 1-kHz signal, modulating the r.f. carrier by 100%. Total harmonic distortion actually decreased to 0.085% in stereo for the same signal and modulation levels. Distortion in mono and stereo for other audio modulating frequencies is shown in Fig. 2. Although measured distortion was low at high frequencies in stereo and mono, I must point out that these figures were obtained using a bandpass filter with a steep roll-off above 15 kHz (the highest broadcast program frequency). Without the filter, subcarrier products were only some 42 dB below 100% modulation levels.

Modell : Denon AVR-X2400H Zustand : sehr gut UVP 649 Zubehör : Antenne Fernbedienung Anleitung als PDF zum Download Messmikrofon Netzkabel Garantie/Gewährleistung : 1Jahr Beschreibung : Der AVR-X2400H 7.2-Kanal-AV-Surround-Receiver bietet unglaublich realistischen Surround Sound, reichlich Verstärker-Leistung und dank der integrierten HEOS Technologie beispiellose Möglichkeiten zur Musikwiedergabe. Die 7 Endstufen des AVR-X2400H ermöglichen Ihnen zwei zusätzliche Overhead-Lautsprecher in einer 5.1.2 Konfiguration anzusteuern. Mit diskret aufgebauten Endstufen auf allen Kanälen bietet der AVR-X2400H eine hohe Leistung von 150 Watt pro Kanal. Der Auto-Eco-Modus passt die Leistungsaufnahme je nach Lautstärke automatisch an und sorgt für ein Energieersparnis. Die Eco-Parameter können ebenfalls auf dem Bildschirm angezeigt werden. Gerüstet für 4K Ultra HD Die fortschrittliche Video-Sektion des AVR-X2400H ist vollständig kompatibel mit den aktuellsten HDMI und HDCP 2.2 Spezifikationen und für alle 4K Ultra HD Quellen vorbereitet. High Dynamic Range (HDR), Dolby Vision Kompatibilität und Hybrid Log Gamma (HLG, über Firmware-Update) sind ebenfalls vorhanden. HDMI Alle acht Eingänge sind mit HDCP 2.2 kompatibel und bieten Unterstützung für 4K Ultra HD 60Hz Video, 4:4:4 Pure Color-Subsampling, High Dynamic Range (HDR) und 21:9 Video, 3D sowie BT.2020 Passthrough. Der AVR-X2400H hat eine fortschrittliche Video-Verarbeitung, um bereits vorhandene Videos mit niedriger Auflösung von DVDs oder anderen digitalen Quellen zu echtem 4K aufzuwerten. Dank der zwei HDMI-Ausgänge können Sie sogar einen TV und Beamer parallel anschließen. Er unterstützt High Dynamic Range (HDR) Videoformate. Er ist sogar für Dolby Vision und HLG (Hybrid Log Gamma; über zukünftiges Firmware-Update) vorbereitet. Dolby Vision führt zu ganz neuen Seh-Erlebnissen, mit erstaunlicher Helligkeit sowie verblüffenden Kontrasten und Farben. Dolby Atmos und DTS:X Spüren Sie mit Dolby Atmos jede Dimension. Mit bewegendem Audio und atemberaubendem Realismus transportiert Dolby Atmos Sie direkt ins Geschehen. Genießen Sie für das ultimative Heimkino-Erlebnis ein 5.1 Surround Sound-Lautsprechersystem und 2 zusätzliche Overhead-Lautsprecher oder 2 Dolby Atmos-Deckenlautsprecher – einschließlich Dolby Surround-Upmixer für ältere Inhalte.Realistisches DTS:X™-Audio platziert den Klang genau da, wo er von Natur aus im Raum erklingen würde und schafft so eine lebensechte, multidimensionale Audioatmosphäre in Ihrem Zuhause. Der erhöhte Realismus zieht Sie direkt in die Welt Ihrer Lieblingsfilme. Die integrierte DTS Neural:X™-Upmixerfunktion verleiht Ihren alten Film-, Spiele- und Musiksammlungen eine ganz neue Dynamik! DTS:X bringt Kino nach Hause. Verbinden und Konfigurieren Vollständig kabellose Verbindungen werden über Bluetooth und Wlan gewährleistet, auch Apple AirPlay wird unterstützt. Die integrierte HEOS Technologie ermöglicht dem AVR-X2400H das App-gesteuerte Herz eines kabellosen Multiroom-Sound-Netzwerks für das ganze Haus zu werden. Der AVR-X2400H ist mit dem Raumakustikkorrektursystem Audyssey MultEQ XT ausgestattet. Über das mitgelieferte Messmikrofon analysiert Audyssey exakt die Leistung aller Lautsprecher, um jeden Kanal zu optimieren. Mit der optionalen Audyssey MultEQ Editor-App (kostenpflichtig für iOS und Android im AppStore erhältlich) können ambitionierte Nutzer auf Wunsch sogar noch weiter gehen. Setup-Assistent Des AVR-X2400H leitet Sie schnell und einfach durch den Einrichtungsvorgang, um die genaueste Konfiguration zu gewährleisten. Optimieren Sie alle Einstellungen Ihres Systems für die bestmögliche Sound- und Videoqualität von Anfang an. Speichern Sie Ihre bevorzugten Einstellungen und Sound-Modi für jede Quelle und rufen Sie diese mit nur einem Tastendruck über die Fernbedienung oder die Vorderseite des AVR auf. Merkmale: 7.2-Kanal-AV-Receiver mit 150 Watt pro Kanal Integriertes WLAN mit Dual Band-Unterstützung 2,4 GHz / 5 GHz; Bluetooth integriert 4K/60 Hz Full-Rate-Passthrough, Dolby Vision kompatibel, HDR, HLG und BT.2020 8 HDMI-Eingänge (davon 1 vorne) mit voller HDCP 2.2 Unterstützung; 2 HDMI-Ausgänge Fortschrittliche Video-Verarbeitung mit 4K-Skalierung für HDMI-Quellen Dolby Atmos und DTS:X (bis zu 5.1.2) Kabellose Multiroom Audio-Technologie von HEOS integriert AirPlay, Bluetooth, Internet Radio, Spotify Connect, SoundCloud, Tidal, Deezer, JUKE!, Napster, Netzwerk-Audio-Streaming DSD (2.8/5.6MHz), FLAC, ALAC und WAV Unterstützung Audyssey MultEQ XT, Dynamic Volume und Dynamic EQ Farblich markierte Lautsprecher-Anschlüsse, Setup-Assistent, Denon 2016 AVR Remote App, HEOS App, Intelligenter Eco-Modus mit drei Einstellungen (Ein/Aus/Automatik)

DescriptionCondition:Used Confirmed Operation.This is a used product and has scratches and scuffs.Everything in the photo is included. Shipping Standard or Expedited Shipping ?FedEx or DHL?The package will arrive 5-14 days after shipment.International Buyers - Please Note:Import duties, taxes, and charges are not included in the item price or shipping cost. These charges are the buyers responsibility. Please check with your countrys customs office to determine what these additional costs will be prior to bidding or buying. Thank you for your understanding.

Key Features: 1. Klipsch RP-400M Bookshelf Speakers (x2): These bookshelf speakers deliver precise, room-filling sound with Klipschs signature horn-loaded technology. Perfect for both music and home theater setups. 2. Klipsch RP-600C Center Speaker: The RP-600C center channel speaker ensures clear dialogue and vocals, making it a crucial component for immersive home theater experiences. 3. Klipsch R-28F Floor-Standing Speakers (x2): These floor-standing speakers are designed for dynamic performance, with a powerful sound that fills the room and enhances any audio source. 4. Klipsch R-115SW Subwoofer: The R-115SW subwoofer adds depth and rumble to your audio, providing rich, low-end frequencies that you can feel. 5. Denon AVR-X3400H Receiver: The Denon AVR-X3400H is a high-quality receiver that provides 7.2-channel processing, 4K Ultra HD support, and various audio enhancement features, making it the perfect hub for your audio setup. Condition: All components in this setup are in excellent condition, well-maintained, and have been thoroughly tested to ensure optimal performance. They are ready to deliver exceptional audio quality for your entertainment needs. Whats Included:2 Klipsch RP-400M Bookshelf Speakers1 Klipsch RP-600C Center Speaker2 Klipsch R-28F Floor-Standing Speakers1 Klipsch R-115SW Subwoofer1 Denon AVR-X3400H ReceiverWith this Klipsch audio setup, youre investing in a premium audio experience that will transform your home entertainment. Dont miss this opportunity to own a complete, high-end audio system. Place your bid now and elevate your sound quality to new heights. If you have any questions or need more information, feel free to reach out. Thank you for considering our listing! ABOUT Customer service is our top priority. If you make a purchase from us and an issue arises, please give us a chance to make things right by contacting us before leaving negative feedback or opening a case. We promise to resolve your concerns quickly and professionally. All of our items are sold as-is but will comply with eBays Money Back Guarantee if your item is not as described. Our products are donated to us and sold directly from stores in the Western Territory Salvation Army. Proceeds are used to support local programs and services. Please study our photos carefully and read our description thoroughly. We maintain office hours Monday through Friday and operate on Eastern time. Purchases or inquiries made after hours will be processed on the next business day. The Salvation Army is not an authorized dealer. Warranty not provided by manufacturer even if the item condition is new (All items sold through The Salvation Army are donated). Please note that this is a previously owned item; imperfections are a unique aspect of a vintage or antique product. Our quality control team has inspected this item and verified that it is in the condition described above. Orders To Cancel your bid on a live auction httpswww.ebay.comhelpactiontopicid=4013 To Cancel an order on an auction that has ended httpswww.ebay.comhelpactiontopicid=4004 To Open a Return Request httpswww.ebay.comhelpactiontopicid=4041 PAYMENTS PayPal payments and credit cards processed through PayPal is the only form of payment we accept. Once the UPI case opens, you will have an additional 4 days to complete the payment before the order is cancelled, and eBay records the nonpayment on your account. Please contact us before the UPI case is closed if additional time is needed. DOMESTIC SHIPPING Please choose the shipping option provided on the listing. If only Free Local Pick up is offered, the item cannot be shipped. Payment must clear before we can ship out an order. We do not ship internationally, to US protectorates, or to FPOAPODPO addresses. Tracking is provided with all orders. We can only ship to your registered eBay address. Please make sure your address is current before purchase. LOCAL PICKUP requests All our local pick-up items are sold directly from Salvation Army store in Ft. Lauderdale, FL. Please verify that you can reasonably travel to the location selling the item before requesting local pickup. Choose Local Pickup before checkout to pay the invoice without any shipping fees. Contact us after the sale to arrange pickup and get detailed pickup information. Business hours will vary. Payment must be tendered online prior to your arrival. INTERNATIONAL SHIPPING We do not ship internationally 100% of the sale of this item will benefit The Salvation Army Fort Lauderdale Adult Rehabilitation Center When you purchase goods from The Salvation Army eBay store in Fort Lauderdale, FL, the proceeds are used to fund our Adult Rehabilitation Centers, where those struggling with drugs and alcohol find help, hope, and a second chance at life. Learn more at SATRUCK.ORGOfficial eBay for Charity listing Learn more Sale benefits a verified non-profit partner Item specifics ConditionUsed An item that has been used previously. The item may have some signs of cosmetic wear, but is fully operational and functions as intended. This item may be a floor model or store return that has been used. See the seller’s listing for full details and description of any imperfections. See all condition definitions

DENON Radio-Tuner Modell TU-40Funktionen überprüft, alles in Ordnung. Keine Gewährleistung, da PRIVATVERKAUF

This Denon DRA-400 Tuner Amp is a fully functional and tested device that will provide you with high-quality audio. It is designed for desktop use and has six input options, two output options, and two channels. The beige color of the device adds a touch of elegance to your setup. The amplifier is suitable for use with components and will give you the best audio experience. The model of the product is DRA 400, which is known for its reliability and durability. Used in great condition

Key Features: 1. Klipsch RP-400M Bookshelf Speakers (x2): These bookshelf speakers deliver precise, room-filling sound with Klipschs signature horn-loaded technology. Perfect for both music and home theater setups. 2. Klipsch RP-600C Center Speaker: The RP-600C center channel speaker ensures clear dialogue and vocals, making it a crucial component for immersive home theater experiences. 3. Klipsch R-28F Floor-Standing Speakers (x2): These floor-standing speakers are designed for dynamic performance, with a powerful sound that fills the room and enhances any audio source. 4. Klipsch R-115SW Subwoofer: The R-115SW subwoofer adds depth and rumble to your audio, providing rich, low-end frequencies that you can feel. 5. Denon AVR-X3400H Receiver: The Denon AVR-X3400H is a high-quality receiver that provides 7.2-channel processing, 4K Ultra HD support, and various audio enhancement features, making it the perfect hub for your audio setup. Condition: All components in this setup are in excellent condition, well-maintained, and have been thoroughly tested to ensure optimal performance. They are ready to deliver exceptional audio quality for your entertainment needs. Whats Included:2 Klipsch RP-400M Bookshelf Speakers1 Klipsch RP-600C Center Speaker2 Klipsch R-28F Floor-Standing Speakers1 Klipsch R-115SW Subwoofer1 Denon AVR-X3400H ReceiverWith this Klipsch audio setup, youre investing in a premium audio experience that will transform your home entertainment. Dont miss this opportunity to own a complete, high-end audio system. Place your bid now and elevate your sound quality to new heights. If you have any questions or need more information, feel free to reach out. Thank you for considering our listing! ABOUT Customer service is our top priority. If you make a purchase from us and an issue arises, please give us a chance to make things right by contacting us before leaving negative feedback or opening a case. We promise to resolve your concerns quickly and professionally. All of our items are sold as-is but will comply with eBays Money Back Guarantee if your item is not as described. Our products are donated to us and sold directly from stores in the Western Territory Salvation Army. Proceeds are used to support local programs and services. Please study our photos carefully and read our description thoroughly. We maintain office hours Monday through Friday and operate on Eastern time. Purchases or inquiries made after hours will be processed on the next business day. The Salvation Army is not an authorized dealer. Warranty not provided by manufacturer even if the item condition is new (All items sold through The Salvation Army are donated). Please note that this is a previously owned item; imperfections are a unique aspect of a vintage or antique product. Our quality control team has inspected this item and verified that it is in the condition described above. Orders To Cancel your bid on a live auction httpswww.ebay.comhelpactiontopicid=4013 To Cancel an order on an auction that has ended httpswww.ebay.comhelpactiontopicid=4004 To Open a Return Request httpswww.ebay.comhelpactiontopicid=4041 PAYMENTS PayPal payments and credit cards processed through PayPal is the only form of payment we accept. Once the UPI case opens, you will have an additional 4 days to complete the payment before the order is cancelled, and eBay records the nonpayment on your account. Please contact us before the UPI case is closed if additional time is needed. DOMESTIC SHIPPING Please choose the shipping option provided on the listing. If only Free Local Pick up is offered, the item cannot be shipped. Payment must clear before we can ship out an order. We do not ship internationally, to US protectorates, or to FPOAPODPO addresses. Tracking is provided with all orders. We can only ship to your registered eBay address. Please make sure your address is current before purchase. LOCAL PICKUP requests All our local pick-up items are sold directly from Salvation Army store in Ft. Lauderdale, FL. Please verify that you can reasonably travel to the location selling the item before requesting local pickup. Choose Local Pickup before checkout to pay the invoice without any shipping fees. Contact us after the sale to arrange pickup and get detailed pickup information. Business hours will vary. Payment must be tendered online prior to your arrival. INTERNATIONAL SHIPPING We do not ship internationally 100% of the sale of this item will benefit The Salvation Army Fort Lauderdale Adult Rehabilitation Center When you purchase goods from The Salvation Army eBay store in Fort Lauderdale, FL, the proceeds are used to fund our Adult Rehabilitation Centers, where those struggling with drugs and alcohol find help, hope, and a second chance at life. Learn more at SATRUCK.ORGOfficial eBay for Charity listing Learn more Sale benefits a verified non-profit partner Item specifics ConditionUsed An item that has been used previously. The item may have some signs of cosmetic wear, but is fully operational and functions as intended. This item may be a floor model or store return that has been used. See the seller’s listing for full details and description of any imperfections. See all condition definitions

Denon DRA 400 Precision Audio Component AM/FM Tuner Stereo AMP Receiver Used, works - Bought at an estate sale, history unknown Tape Deck Not Included Video available of working FM and Cassette under extra kart parts youtube channel - message for link Below description found online and buyer must confirm accuracy- reference only - Info from gamma electronics - XYZ Manufacturers Specifications FM Tuner Section: Usable Mono Sensitivity: 10.3 dBf. S/N Ratio: Mono, 75 dB; stereo, 72 dB. THD at 1 kHz: Mono, 0.1%; stereo, 0.2%. Capture Ratio: 1.2 dB. Image Rejection: 45 dB. AM Suppression: 60 dB. Stereo Separation, 1 kHz: 50 dB. Frequency Response: 10 Hz to 15 kHz, +0.2,-1.5 dB. AM Tuner Section: Usable Sensitivity: 15 dB. S/N Ratio: 55 dB. Amplifier Section: Power Output: 40 watts per channel, 8 ohms, 20 Hz to 20 kHz (50 watts, 1 kHz, 4 ohms). THD: 0.02%, 8 ohms. Damping Factor: 80, 1 kHz, 8 ohms. Input Sensitivity: MM phono, 2.5 mV; MC phono, 0.25 mV; high level, 150 mV. Maximum Phono Input Level: MM phono, 200 mV; MC phono, 20 mV. Frequency Response: Phono, RIAA 0.5 dB; high level, 20 Hz to 20 kHz, 0.5 dB. S/N Ratio: MM phono, 80 dB; MC phono, 62 dB; high level, 96 dB. Tone Control Range: 10 dB at 50 Hz and 10 kHz. Subsonic Filter Cutoff: 18 Hz, 6 dB per octave. General Specifications: Power Consumption: 130 watts. Dimensions: 17.1 in. (43.4 cm) W x 4.4 in. (11.2 cm) H x 16.1 in. (40.8 cm) D. Weight: 19.8 lbs. (9.0 kg). Price: $399.95. Company Address: 61 Law Dr., Fairfield, N.J. 07006. As so often happens with advances in audio technology, new features are first incorporated in top-of-the-line separate components which are beyond the reach of all but the most affluent of audio enthusiasts. Later on, these features filter down to high-powered, high-priced all-in-one receiv ers, where a larger audience is potentially available. Finally, they are incorporated into relatively low-cost, medium-powered receivers that just about anyone interested in good sound can afford. The Denon DRA-400 is a good example of a receiver which has benefited from technology first found in higher priced units. This receiver employs crystal-controlled, frequency-synthesized tuning for accuracy and has a five-station preset capability with battery-operated memory backup. Not only does the phono preamplifier section incorporate both moving-magnet and moving-coil inputs (the latter at an input impedance of 100 ohms), but the phono preamp-equalizer section has a direct-coupled input. The power amplifier section employs a non-switching biasing circuit for the elimination of so-called switching and notch distortion at the output stages. These refinements would have been found only on more expensive components just a few years ago. The front panel of the Denon DRA-400 is neatly divided into highly functional upper and lower sections. The upper section contains the power on/off switch, a numeric display of station frequency, a stereo indicator light, a signal-strength LED indicator, up and down tuning buttons, the five preset buttons and their memory switch, program selector pushbuttons, and a large, rotary master-volume control. The signal-strength indicator takes the form of a go-no-go indicator, rather than a signal-strength meter: It lights when the incoming signal strength is deemed adequate and does not light when weaker signals are received-an interesting approach but not very useful. Controls in the lower section are normally covered by a swing-down hinged door, since they are used less frequently than those just described. Behind the door panel are a stereo headphone jack; a pair of speaker selector buttons; bass, treble and balance controls; a three-position monitor/ copy switch; a subsonic filter switch; a stereo/mono switch (associated with FM reception); an MM/MC phono switch, and a loudness on/off switch. The rear panel of the DRA-400 is equipped with the usual 75- and 300-ohm FM antenna terminals, phono and high level input terminals, two pairs of tape in/out jacks, two pairs of color-coded speaker connection terminals, a chassis ground terminal, and a pair of a.c. convenience outlets (one switched, one unswitched). Instead of the usual AM loop stick antenna, a more elaborate, true AM loop antenna is packed with the receiver as a separate item; its two leads must be connected to the appropriate AM and ground terminals on the back of the set. The pivotable loop antenna is best snapped into an antenna holder during receiver installation so the antenna can still be rotated for best AM reception. Since this loop antenna forms part of the input-stage tuned circuit, the owners manual suggests that even if an outdoor AM antenna is used (because of inadequate signal strength), the loop antennas leads should remain connected to their appropriate terminals, in parallel with the outdoor antenna leads. Tuner Measurements Usable mono FM sensitivity fell short of published claims, measuring 16 dBf (3.47 V across 300 ohms). In stereo, sensitivity was limited by muting and stereo thresholds, which were set to 32 dBf (21.9 V). For 50-dB quieting in mono, an input signal strength of 19.5 dBf (5.2 V) was required; for stereo, a signal strength of 42 dBf (69.2 V) was needed. Plots of quieting and distortion (at 1 kHz) versus signal strength are shown in Fig. 1. Signal-to-noise in mono, at 65 dBf of input signal, measured 75 dB as claimed; in stereo it was 72 dB, also exactly as claimed. Harmonic distortion in mono measured 0.17% for a 1-kHz signal, modulating the r.f. carrier by 100%. Total harmonic distortion actually decreased to 0.085% in stereo for the same signal and modulation levels. Distortion in mono and stereo for other audio modulating frequencies is shown in Fig. 2. Although measured distortion was low at high frequencies in stereo and mono, I must point out that these figures were obtained using a bandpass filter with a steep roll-off above 15 kHz (the highest broadcast program frequency). Without the filter, subcarrier products were only some 42 dB below 100% modulation levels.

DENON Radio-Tuner Modell TU-40Funktionen überprüft, alles in Ordnung. Keine Gewährleistung, da PRIVATVERKAUF

listing many other similar items! >>>Visit StoreDescription Condition: Used Brand: DENON DP-400 450 Tone Arm Sub Weight 50g for Record Player/Turntable Thank you for viewing.record playerDENON/DENONFor DP-400 DP-450This is a production sub weight 50g (1 piece).*The main weight in the image is not included.?Size See imageInner diameter matches main weight outer diameterOuter diameter approximately 38mm ?MaterialSub weight: Brass (3604)Stopper: Brass (3604)*Brass screw with a flat tip that is gentle on the shaftEasy to use flathead screw*Uses non-magnetic material suitable for audio?Condition See imageThe brass color gives it a luxurious feel.*As this is a manufactured product, there may be lathe marks and chuck scratches. There are cases where this happens. note that?How to useCartridge + shell weight is heavy and zero balanceIf you cannot remove it, put it over the main weight.Install and balance.Please check the stylus pressure with a precision meter.*Expanding the choice of cartridges and shells It is an item*This does not necessarily guarantee zero balance. there is no?AccessoriesSub weight, anti-rotation (M4 screw)With protective tape*The main weight and scale in the image are not included.*Please inquire for detailed information. Size differences, weight, etc. due to production weight If you have any requests, please ask.Those who are in trouble because they dont have a sub weight,Please try this opportunity. Please check the picture for the condition of the product. Please refrain from nervous people and those who seek perfection.I am waiting for a question by a message?There may be an error in the Item specifics. ?Please give priority to photos and descriptions. Please read the full item description and contact us with any questions you may have prior to purchasing.Please let me know if there are any other products you want. Even if the condition is Unused, it has been handed to someone once, so we list it as a used item. Please purchase only if you understand the second hand product. The items we are selling are used in Japan. You may need a transformer for use in your country.Payment Please pay within 5 days after auction is finished.Shipping We ship to world wide for free by SAL(With tracking number). All items will be carefully packed and shipped to you directly from Japan.International Buyers - Please Note: Import duties, taxes, and charges are not included in the item price or shipping cost. These charges are the buyers responsibility. Please check with your countrys customs office to determine what these additional costs will be prior to bidding or buying.Provided by HARU

COSMETIC CONDITION: VERY GOOD FUNCTIONAL CONDITION: WORKING SKU: E109 LISTING INCLUDES: Unit, power supply, additional wiers The listing does not include other parts or accessories. The photos show what you will receive. DESCRIPTION: Unit works. Good condition. Missing headshell cartridge. PAYMENTS: Signature may be required for orders over $500. Taxes for some states may be added. eBay Sales Tax Info. Payment for items must be made within 4 days. After that time, items still awaiting payment are automatically canceled. SHIPPING & RETURNS: Orders are generally shipped the same day or the next business day after payment is cleared. No returns if item is modified or warranty sticker is removed. Liquid, misuse, accidental damage is also not covered. We inspect all returns for matching serial numbers, defects and damages. Free returns if an item is not as described. CUSTOMER SERVICE: Monday - Friday, 9:00 a.m. to 5:00 p.m. CST is our customer service operating hours.

Denon DRA 400 Precision Audio Component AM/FM Tuner Stereo AMP Receiver Used, works - Bought at an estate sale, history unknown Tape Deck Not Included Video available of working FM and Cassette under extra kart parts youtube channel - message for link Below description found online and buyer must confirm accuracy- reference only - Info from gamma electronics - XYZ Manufacturers Specifications FM Tuner Section: Usable Mono Sensitivity: 10.3 dBf. S/N Ratio: Mono, 75 dB; stereo, 72 dB. THD at 1 kHz: Mono, 0.1%; stereo, 0.2%. Capture Ratio: 1.2 dB. Image Rejection: 45 dB. AM Suppression: 60 dB. Stereo Separation, 1 kHz: 50 dB. Frequency Response: 10 Hz to 15 kHz, +0.2,-1.5 dB. AM Tuner Section: Usable Sensitivity: 15 dB. S/N Ratio: 55 dB. Amplifier Section: Power Output: 40 watts per channel, 8 ohms, 20 Hz to 20 kHz (50 watts, 1 kHz, 4 ohms). THD: 0.02%, 8 ohms. Damping Factor: 80, 1 kHz, 8 ohms. Input Sensitivity: MM phono, 2.5 mV; MC phono, 0.25 mV; high level, 150 mV. Maximum Phono Input Level: MM phono, 200 mV; MC phono, 20 mV. Frequency Response: Phono, RIAA 0.5 dB; high level, 20 Hz to 20 kHz, 0.5 dB. S/N Ratio: MM phono, 80 dB; MC phono, 62 dB; high level, 96 dB. Tone Control Range: 10 dB at 50 Hz and 10 kHz. Subsonic Filter Cutoff: 18 Hz, 6 dB per octave. General Specifications: Power Consumption: 130 watts. Dimensions: 17.1 in. (43.4 cm) W x 4.4 in. (11.2 cm) H x 16.1 in. (40.8 cm) D. Weight: 19.8 lbs. (9.0 kg). Price: $399.95. Company Address: 61 Law Dr., Fairfield, N.J. 07006. As so often happens with advances in audio technology, new features are first incorporated in top-of-the-line separate components which are beyond the reach of all but the most affluent of audio enthusiasts. Later on, these features filter down to high-powered, high-priced all-in-one receiv ers, where a larger audience is potentially available. Finally, they are incorporated into relatively low-cost, medium-powered receivers that just about anyone interested in good sound can afford. The Denon DRA-400 is a good example of a receiver which has benefited from technology first found in higher priced units. This receiver employs crystal-controlled, frequency-synthesized tuning for accuracy and has a five-station preset capability with battery-operated memory backup. Not only does the phono preamplifier section incorporate both moving-magnet and moving-coil inputs (the latter at an input impedance of 100 ohms), but the phono preamp-equalizer section has a direct-coupled input. The power amplifier section employs a non-switching biasing circuit for the elimination of so-called switching and notch distortion at the output stages. These refinements would have been found only on more expensive components just a few years ago. The front panel of the Denon DRA-400 is neatly divided into highly functional upper and lower sections. The upper section contains the power on/off switch, a numeric display of station frequency, a stereo indicator light, a signal-strength LED indicator, up and down tuning buttons, the five preset buttons and their memory switch, program selector pushbuttons, and a large, rotary master-volume control. The signal-strength indicator takes the form of a go-no-go indicator, rather than a signal-strength meter: It lights when the incoming signal strength is deemed adequate and does not light when weaker signals are received-an interesting approach but not very useful. Controls in the lower section are normally covered by a swing-down hinged door, since they are used less frequently than those just described. Behind the door panel are a stereo headphone jack; a pair of speaker selector buttons; bass, treble and balance controls; a three-position monitor/ copy switch; a subsonic filter switch; a stereo/mono switch (associated with FM reception); an MM/MC phono switch, and a loudness on/off switch. The rear panel of the DRA-400 is equipped with the usual 75- and 300-ohm FM antenna terminals, phono and high level input terminals, two pairs of tape in/out jacks, two pairs of color-coded speaker connection terminals, a chassis ground terminal, and a pair of a.c. convenience outlets (one switched, one unswitched). Instead of the usual AM loop stick antenna, a more elaborate, true AM loop antenna is packed with the receiver as a separate item; its two leads must be connected to the appropriate AM and ground terminals on the back of the set. The pivotable loop antenna is best snapped into an antenna holder during receiver installation so the antenna can still be rotated for best AM reception. Since this loop antenna forms part of the input-stage tuned circuit, the owners manual suggests that even if an outdoor AM antenna is used (because of inadequate signal strength), the loop antennas leads should remain connected to their appropriate terminals, in parallel with the outdoor antenna leads. Tuner Measurements Usable mono FM sensitivity fell short of published claims, measuring 16 dBf (3.47 V across 300 ohms). In stereo, sensitivity was limited by muting and stereo thresholds, which were set to 32 dBf (21.9 V). For 50-dB quieting in mono, an input signal strength of 19.5 dBf (5.2 V) was required; for stereo, a signal strength of 42 dBf (69.2 V) was needed. Plots of quieting and distortion (at 1 kHz) versus signal strength are shown in Fig. 1. Signal-to-noise in mono, at 65 dBf of input signal, measured 75 dB as claimed; in stereo it was 72 dB, also exactly as claimed. Harmonic distortion in mono measured 0.17% for a 1-kHz signal, modulating the r.f. carrier by 100%. Total harmonic distortion actually decreased to 0.085% in stereo for the same signal and modulation levels. Distortion in mono and stereo for other audio modulating frequencies is shown in Fig. 2. Although measured distortion was low at high frequencies in stereo and mono, I must point out that these figures were obtained using a bandpass filter with a steep roll-off above 15 kHz (the highest broadcast program frequency). Without the filter, subcarrier products were only some 42 dB below 100% modulation levels.

OPEN BOX TESTED, APPEARS TO HAVE NOT BEEN USED. IN ORIGINAL BOX BUT MISSING THE STYROFOAM INSERTS. ITEM WILL BE WELL WRAPPED IN BUBBLE WRAP FOR BOTH OUR PROTECTION, PLEASE WATCH THE VIDEO AS IT SHOWS THE TURNTABLE WORKING AS IT SHOULD. THE PLASTIC 45 RPM ADAPTOR IS NOT THE ORIGINAL BUT AN AFTERMARKET ONE About this itemREDISCOVER YOUR PASSION FOR VINYL – Give your old analog records a digital rebirth with this state-of-the-art automatic turntable that supports 33 1/3 rpm, 45 rpm or 78 rpm, covering a wide array of rotating speedsMORE FEATURES, MORE FLEXIBILITY – The DP400 is equipped with weighted belt-driven platter, one-touch button controls, supports both MM and MC cartridges to suit your preferences, a speed auto sensor for accurate sound each time, and moreA UNIQUE CURVED TONEARM DESIGN – Carefully designed horizontal tracking angled tonearm with auto-lift and playback stop HELPS PRESERVE YOUR RECORDS WITHOUT DAMAGING THEM by reducing harmonic distortion and giving crystal clear soundBUILT-IN PHONO EQUALIZER creates an open, enveloping sound stage that enlivens your vinyl collection while staying true to the original recording. Connect it directly to a mini component or integrated amp that lacks a phono terminal for seamless useEASY INSTALLATION & SETUP – Comes with a pre-mounted cartridge, setting the turntable up in your living room or home theater is simple. Instantly start listening to your treasured vinyl collectionULTIMATE AUDIO EXPERIENCE – Clean aesthetics, modern design & solid build quality, with Denons expert re-engineering, makes this elegant table a must have for your vintage vinyl collection in your home entertainment system

Denon DRA 400 Precision Audio Component AM/FM Tuner Stereo AMP Receiver Used, works - Bought at an estate sale, history unknown Tape Deck Not Included Video available of working FM and Cassette under extra kart parts youtube channel - message for link Below description found online and buyer must confirm accuracy- reference only - Info from gamma electronics - XYZ Manufacturers Specifications FM Tuner Section: Usable Mono Sensitivity: 10.3 dBf. S/N Ratio: Mono, 75 dB; stereo, 72 dB. THD at 1 kHz: Mono, 0.1%; stereo, 0.2%. Capture Ratio: 1.2 dB. Image Rejection: 45 dB. AM Suppression: 60 dB. Stereo Separation, 1 kHz: 50 dB. Frequency Response: 10 Hz to 15 kHz, +0.2,-1.5 dB. AM Tuner Section: Usable Sensitivity: 15 dB. S/N Ratio: 55 dB. Amplifier Section: Power Output: 40 watts per channel, 8 ohms, 20 Hz to 20 kHz (50 watts, 1 kHz, 4 ohms). THD: 0.02%, 8 ohms. Damping Factor: 80, 1 kHz, 8 ohms. Input Sensitivity: MM phono, 2.5 mV; MC phono, 0.25 mV; high level, 150 mV. Maximum Phono Input Level: MM phono, 200 mV; MC phono, 20 mV. Frequency Response: Phono, RIAA 0.5 dB; high level, 20 Hz to 20 kHz, 0.5 dB. S/N Ratio: MM phono, 80 dB; MC phono, 62 dB; high level, 96 dB. Tone Control Range: 10 dB at 50 Hz and 10 kHz. Subsonic Filter Cutoff: 18 Hz, 6 dB per octave. General Specifications: Power Consumption: 130 watts. Dimensions: 17.1 in. (43.4 cm) W x 4.4 in. (11.2 cm) H x 16.1 in. (40.8 cm) D. Weight: 19.8 lbs. (9.0 kg). Price: $399.95. Company Address: 61 Law Dr., Fairfield, N.J. 07006. As so often happens with advances in audio technology, new features are first incorporated in top-of-the-line separate components which are beyond the reach of all but the most affluent of audio enthusiasts. Later on, these features filter down to high-powered, high-priced all-in-one receiv ers, where a larger audience is potentially available. Finally, they are incorporated into relatively low-cost, medium-powered receivers that just about anyone interested in good sound can afford. The Denon DRA-400 is a good example of a receiver which has benefited from technology first found in higher priced units. This receiver employs crystal-controlled, frequency-synthesized tuning for accuracy and has a five-station preset capability with battery-operated memory backup. Not only does the phono preamplifier section incorporate both moving-magnet and moving-coil inputs (the latter at an input impedance of 100 ohms), but the phono preamp-equalizer section has a direct-coupled input. The power amplifier section employs a non-switching biasing circuit for the elimination of so-called switching and notch distortion at the output stages. These refinements would have been found only on more expensive components just a few years ago. The front panel of the Denon DRA-400 is neatly divided into highly functional upper and lower sections. The upper section contains the power on/off switch, a numeric display of station frequency, a stereo indicator light, a signal-strength LED indicator, up and down tuning buttons, the five preset buttons and their memory switch, program selector pushbuttons, and a large, rotary master-volume control. The signal-strength indicator takes the form of a go-no-go indicator, rather than a signal-strength meter: It lights when the incoming signal strength is deemed adequate and does not light when weaker signals are received-an interesting approach but not very useful. Controls in the lower section are normally covered by a swing-down hinged door, since they are used less frequently than those just described. Behind the door panel are a stereo headphone jack; a pair of speaker selector buttons; bass, treble and balance controls; a three-position monitor/ copy switch; a subsonic filter switch; a stereo/mono switch (associated with FM reception); an MM/MC phono switch, and a loudness on/off switch. The rear panel of the DRA-400 is equipped with the usual 75- and 300-ohm FM antenna terminals, phono and high level input terminals, two pairs of tape in/out jacks, two pairs of color-coded speaker connection terminals, a chassis ground terminal, and a pair of a.c. convenience outlets (one switched, one unswitched). Instead of the usual AM loop stick antenna, a more elaborate, true AM loop antenna is packed with the receiver as a separate item; its two leads must be connected to the appropriate AM and ground terminals on the back of the set. The pivotable loop antenna is best snapped into an antenna holder during receiver installation so the antenna can still be rotated for best AM reception. Since this loop antenna forms part of the input-stage tuned circuit, the owners manual suggests that even if an outdoor AM antenna is used (because of inadequate signal strength), the loop antennas leads should remain connected to their appropriate terminals, in parallel with the outdoor antenna leads. Tuner Measurements Usable mono FM sensitivity fell short of published claims, measuring 16 dBf (3.47 V across 300 ohms). In stereo, sensitivity was limited by muting and stereo thresholds, which were set to 32 dBf (21.9 V). For 50-dB quieting in mono, an input signal strength of 19.5 dBf (5.2 V) was required; for stereo, a signal strength of 42 dBf (69.2 V) was needed. Plots of quieting and distortion (at 1 kHz) versus signal strength are shown in Fig. 1. Signal-to-noise in mono, at 65 dBf of input signal, measured 75 dB as claimed; in stereo it was 72 dB, also exactly as claimed. Harmonic distortion in mono measured 0.17% for a 1-kHz signal, modulating the r.f. carrier by 100%. Total harmonic distortion actually decreased to 0.085% in stereo for the same signal and modulation levels. Distortion in mono and stereo for other audio modulating frequencies is shown in Fig. 2. Although measured distortion was low at high frequencies in stereo and mono, I must point out that these figures were obtained using a bandpass filter with a steep roll-off above 15 kHz (the highest broadcast program frequency). Without the filter, subcarrier products were only some 42 dB below 100% modulation levels.

Denon CD-Player DCD-1400 mit Fernbedienung & Bedienungsanleitung, defekt! Das Gerät funktioniert eigentlich noch hervorragend, nur muss man immer häufiger die CD einige Male heraus- und wieder rein fahren, bis sie erkannt wird. Wenn die CD dann erkannt wurde, läuft alles problemlos, keinerlei Aussetzer oder Ähnliches. Bisher hat der Player noch jede CD nach maximal 4-5 Versuchen eingelesen, öfter geht es auch sofort. Aus diesen Gründen wird das Gerät ausdrücklich als Defekt verkauft. Inklusive Fernbedienung & Bedienungsanleitung. Privatverkauf, keine Garantie, keine Gewährleistung, keine Rücknahme. Achtung: Das Gerät stand mehrere Jahre in einem Raucherhaushalt. Ich rieche zwar nichts mehr, aber ich habe auch keinen feine Geruchssinn. Empfindliche Nasen seien hiermit vorgewarnt. Technische Daten: Wandler: 20-Bit-Echtzeit-Super-Linearkonverter, jeweils für den rechten und linken Kanal getrenntFrequenzgang: 2 - 20.000 HzDynamikbereich: 97 dBSignalrauschabstand: 108 dBKlirrfaktor: 1 kHz: 0,003% (1kHz)Kanaltrennung: ~ 103 dBTitel-ProgrammierungRepeatSpielt CD-R/CD-RW/HDCD: CD-R, CD-RW Ausgänge:2 x Stereo-Cinch-Ausgang (fix + variabel per Fernbedienung)1 optischer Digitalausgang1 koaxialer Digitalausgang1 Kopfhörerausgang (regelbar) Gewicht: ca. 7,3 kg Abmessungen (B x H x T): 434 x 112 x 314 mm

Denon DRA 400 Precision Audio Component AM/FM Tuner Stereo AMP Receiver Used, works - Bought at an estate sale, history unknown Tape Deck Not Included Video available of working FM and Cassette under extra kart parts youtube channel - message for link Below description found online and buyer must confirm accuracy- reference only - Info from gamma electronics - XYZ Manufacturers Specifications FM Tuner Section: Usable Mono Sensitivity: 10.3 dBf. S/N Ratio: Mono, 75 dB; stereo, 72 dB. THD at 1 kHz: Mono, 0.1%; stereo, 0.2%. Capture Ratio: 1.2 dB. Image Rejection: 45 dB. AM Suppression: 60 dB. Stereo Separation, 1 kHz: 50 dB. Frequency Response: 10 Hz to 15 kHz, +0.2,-1.5 dB. AM Tuner Section: Usable Sensitivity: 15 dB. S/N Ratio: 55 dB. Amplifier Section: Power Output: 40 watts per channel, 8 ohms, 20 Hz to 20 kHz (50 watts, 1 kHz, 4 ohms). THD: 0.02%, 8 ohms. Damping Factor: 80, 1 kHz, 8 ohms. Input Sensitivity: MM phono, 2.5 mV; MC phono, 0.25 mV; high level, 150 mV. Maximum Phono Input Level: MM phono, 200 mV; MC phono, 20 mV. Frequency Response: Phono, RIAA 0.5 dB; high level, 20 Hz to 20 kHz, 0.5 dB. S/N Ratio: MM phono, 80 dB; MC phono, 62 dB; high level, 96 dB. Tone Control Range: 10 dB at 50 Hz and 10 kHz. Subsonic Filter Cutoff: 18 Hz, 6 dB per octave. General Specifications: Power Consumption: 130 watts. Dimensions: 17.1 in. (43.4 cm) W x 4.4 in. (11.2 cm) H x 16.1 in. (40.8 cm) D. Weight: 19.8 lbs. (9.0 kg). Price: $399.95. Company Address: 61 Law Dr., Fairfield, N.J. 07006. As so often happens with advances in audio technology, new features are first incorporated in top-of-the-line separate components which are beyond the reach of all but the most affluent of audio enthusiasts. Later on, these features filter down to high-powered, high-priced all-in-one receiv ers, where a larger audience is potentially available. Finally, they are incorporated into relatively low-cost, medium-powered receivers that just about anyone interested in good sound can afford. The Denon DRA-400 is a good example of a receiver which has benefited from technology first found in higher priced units. This receiver employs crystal-controlled, frequency-synthesized tuning for accuracy and has a five-station preset capability with battery-operated memory backup. Not only does the phono preamplifier section incorporate both moving-magnet and moving-coil inputs (the latter at an input impedance of 100 ohms), but the phono preamp-equalizer section has a direct-coupled input. The power amplifier section employs a non-switching biasing circuit for the elimination of so-called switching and notch distortion at the output stages. These refinements would have been found only on more expensive components just a few years ago. The front panel of the Denon DRA-400 is neatly divided into highly functional upper and lower sections. The upper section contains the power on/off switch, a numeric display of station frequency, a stereo indicator light, a signal-strength LED indicator, up and down tuning buttons, the five preset buttons and their memory switch, program selector pushbuttons, and a large, rotary master-volume control. The signal-strength indicator takes the form of a go-no-go indicator, rather than a signal-strength meter: It lights when the incoming signal strength is deemed adequate and does not light when weaker signals are received-an interesting approach but not very useful. Controls in the lower section are normally covered by a swing-down hinged door, since they are used less frequently than those just described. Behind the door panel are a stereo headphone jack; a pair of speaker selector buttons; bass, treble and balance controls; a three-position monitor/ copy switch; a subsonic filter switch; a stereo/mono switch (associated with FM reception); an MM/MC phono switch, and a loudness on/off switch. The rear panel of the DRA-400 is equipped with the usual 75- and 300-ohm FM antenna terminals, phono and high level input terminals, two pairs of tape in/out jacks, two pairs of color-coded speaker connection terminals, a chassis ground terminal, and a pair of a.c. convenience outlets (one switched, one unswitched). Instead of the usual AM loop stick antenna, a more elaborate, true AM loop antenna is packed with the receiver as a separate item; its two leads must be connected to the appropriate AM and ground terminals on the back of the set. The pivotable loop antenna is best snapped into an antenna holder during receiver installation so the antenna can still be rotated for best AM reception. Since this loop antenna forms part of the input-stage tuned circuit, the owners manual suggests that even if an outdoor AM antenna is used (because of inadequate signal strength), the loop antennas leads should remain connected to their appropriate terminals, in parallel with the outdoor antenna leads. Tuner Measurements Usable mono FM sensitivity fell short of published claims, measuring 16 dBf (3.47 V across 300 ohms). In stereo, sensitivity was limited by muting and stereo thresholds, which were set to 32 dBf (21.9 V). For 50-dB quieting in mono, an input signal strength of 19.5 dBf (5.2 V) was required; for stereo, a signal strength of 42 dBf (69.2 V) was needed. Plots of quieting and distortion (at 1 kHz) versus signal strength are shown in Fig. 1. Signal-to-noise in mono, at 65 dBf of input signal, measured 75 dB as claimed; in stereo it was 72 dB, also exactly as claimed. Harmonic distortion in mono measured 0.17% for a 1-kHz signal, modulating the r.f. carrier by 100%. Total harmonic distortion actually decreased to 0.085% in stereo for the same signal and modulation levels. Distortion in mono and stereo for other audio modulating frequencies is shown in Fig. 2. Although measured distortion was low at high frequencies in stereo and mono, I must point out that these figures were obtained using a bandpass filter with a steep roll-off above 15 kHz (the highest broadcast program frequency). Without the filter, subcarrier products were only some 42 dB below 100% modulation levels.

Denon DRA 400 Precision Audio Component AM/FM Tuner Stereo AMP Receiver Used, works - Bought at an estate sale, history unknown Tape Deck Not Included Video available of working FM and Cassette under extra kart parts youtube channel - message for link Below description found online and buyer must confirm accuracy- reference only - Info from gamma electronics - XYZ Manufacturers Specifications FM Tuner Section: Usable Mono Sensitivity: 10.3 dBf. S/N Ratio: Mono, 75 dB; stereo, 72 dB. THD at 1 kHz: Mono, 0.1%; stereo, 0.2%. Capture Ratio: 1.2 dB. Image Rejection: 45 dB. AM Suppression: 60 dB. Stereo Separation, 1 kHz: 50 dB. Frequency Response: 10 Hz to 15 kHz, +0.2,-1.5 dB. AM Tuner Section: Usable Sensitivity: 15 dB. S/N Ratio: 55 dB. Amplifier Section: Power Output: 40 watts per channel, 8 ohms, 20 Hz to 20 kHz (50 watts, 1 kHz, 4 ohms). THD: 0.02%, 8 ohms. Damping Factor: 80, 1 kHz, 8 ohms. Input Sensitivity: MM phono, 2.5 mV; MC phono, 0.25 mV; high level, 150 mV. Maximum Phono Input Level: MM phono, 200 mV; MC phono, 20 mV. Frequency Response: Phono, RIAA 0.5 dB; high level, 20 Hz to 20 kHz, 0.5 dB. S/N Ratio: MM phono, 80 dB; MC phono, 62 dB; high level, 96 dB. Tone Control Range: 10 dB at 50 Hz and 10 kHz. Subsonic Filter Cutoff: 18 Hz, 6 dB per octave. General Specifications: Power Consumption: 130 watts. Dimensions: 17.1 in. (43.4 cm) W x 4.4 in. (11.2 cm) H x 16.1 in. (40.8 cm) D. Weight: 19.8 lbs. (9.0 kg). Price: $399.95. Company Address: 61 Law Dr., Fairfield, N.J. 07006. As so often happens with advances in audio technology, new features are first incorporated in top-of-the-line separate components which are beyond the reach of all but the most affluent of audio enthusiasts. Later on, these features filter down to high-powered, high-priced all-in-one receiv ers, where a larger audience is potentially available. Finally, they are incorporated into relatively low-cost, medium-powered receivers that just about anyone interested in good sound can afford. The Denon DRA-400 is a good example of a receiver which has benefited from technology first found in higher priced units. This receiver employs crystal-controlled, frequency-synthesized tuning for accuracy and has a five-station preset capability with battery-operated memory backup. Not only does the phono preamplifier section incorporate both moving-magnet and moving-coil inputs (the latter at an input impedance of 100 ohms), but the phono preamp-equalizer section has a direct-coupled input. The power amplifier section employs a non-switching biasing circuit for the elimination of so-called switching and notch distortion at the output stages. These refinements would have been found only on more expensive components just a few years ago. The front panel of the Denon DRA-400 is neatly divided into highly functional upper and lower sections. The upper section contains the power on/off switch, a numeric display of station frequency, a stereo indicator light, a signal-strength LED indicator, up and down tuning buttons, the five preset buttons and their memory switch, program selector pushbuttons, and a large, rotary master-volume control. The signal-strength indicator takes the form of a go-no-go indicator, rather than a signal-strength meter: It lights when the incoming signal strength is deemed adequate and does not light when weaker signals are received-an interesting approach but not very useful. Controls in the lower section are normally covered by a swing-down hinged door, since they are used less frequently than those just described. Behind the door panel are a stereo headphone jack; a pair of speaker selector buttons; bass, treble and balance controls; a three-position monitor/ copy switch; a subsonic filter switch; a stereo/mono switch (associated with FM reception); an MM/MC phono switch, and a loudness on/off switch. The rear panel of the DRA-400 is equipped with the usual 75- and 300-ohm FM antenna terminals, phono and high level input terminals, two pairs of tape in/out jacks, two pairs of color-coded speaker connection terminals, a chassis ground terminal, and a pair of a.c. convenience outlets (one switched, one unswitched). Instead of the usual AM loop stick antenna, a more elaborate, true AM loop antenna is packed with the receiver as a separate item; its two leads must be connected to the appropriate AM and ground terminals on the back of the set. The pivotable loop antenna is best snapped into an antenna holder during receiver installation so the antenna can still be rotated for best AM reception. Since this loop antenna forms part of the input-stage tuned circuit, the owners manual suggests that even if an outdoor AM antenna is used (because of inadequate signal strength), the loop antennas leads should remain connected to their appropriate terminals, in parallel with the outdoor antenna leads. Tuner Measurements Usable mono FM sensitivity fell short of published claims, measuring 16 dBf (3.47 V across 300 ohms). In stereo, sensitivity was limited by muting and stereo thresholds, which were set to 32 dBf (21.9 V). For 50-dB quieting in mono, an input signal strength of 19.5 dBf (5.2 V) was required; for stereo, a signal strength of 42 dBf (69.2 V) was needed. Plots of quieting and distortion (at 1 kHz) versus signal strength are shown in Fig. 1. Signal-to-noise in mono, at 65 dBf of input signal, measured 75 dB as claimed; in stereo it was 72 dB, also exactly as claimed. Harmonic distortion in mono measured 0.17% for a 1-kHz signal, modulating the r.f. carrier by 100%. Total harmonic distortion actually decreased to 0.085% in stereo for the same signal and modulation levels. Distortion in mono and stereo for other audio modulating frequencies is shown in Fig. 2. Although measured distortion was low at high frequencies in stereo and mono, I must point out that these figures were obtained using a bandpass filter with a steep roll-off above 15 kHz (the highest broadcast program frequency). Without the filter, subcarrier products were only some 42 dB below 100% modulation levels.

This turntable is brand new, never used. But it is an open box and the box is pretty rough. See pic. But all the packing materials inside are not damaged. I did plug it in to make sure it turns on. Introducing the Denon DP-400 turntable in white color. This high-quality record player features a dust cover and the ability to play at three different speed settings - 45RPM, 33.3RPM, and 78RPM. The model is Denon DP400, making it a reliable choice for music lovers. The item is brand new and comes in an open box, ready for use. Its sleek design makes it a perfect fit for any home audio setup. Don't miss out on the opportunity to own this top-of-the-line record player.

Denon Poa-4400 Mono-Endstufen 2 Stück!. Ich verkaufe 2 Mono- Endstufen der Marke Denon. Die Mono Endstufen sind die Denon Poa-4400. Ich brauche sie nicht mehr und deshalb möchte ich sie verkaufen. Die Endstufen sind in einen guten Zustand. Daten Allgemein Hersteller: Denon Modell: POA-4400 Baujahre: 1987 - 1988 Hergestellt in: Japan Farbe: Schwarz Fernbedienung: Nein Leistungsaufnahme: 350 Watt (IEC) Abmessungen: 310 x 192 x 420 mm (BxHxT) Gewicht: 10,3 kg Anschlüsse Anzahl der Eingänge: Cinch 1 V /25 KOhm XLR 1 V/10 KOhm Anzahl der Ausgänge: 2x Lautsprecher Technische Daten Dauerleistung (bei Klirrfaktor) 8 Ohm: 150 Watt <0,02% 4 Ohm: 250 Watt DIN Dynamikleistung 8 Ohm: 4 Ohm: 400 Watt 2 Ohm: 500 Watt 1 Ohm: 600 Watt Gesamtklirrfaktor: < 0,002% (-3 dB bei Nennleistung an 8 Ohm) Dämpfungsfaktor: Frequenzgang: 1 Hz - 300 kHz (+0/-3dB, 1 W) Signalrauschabstand: 123 dB (IHF, A-Bewertung, XLR)

Denon DRA 400 Precision Audio Component AM/FM Tuner Stereo AMP Receiver Used, works - Bought at an estate sale, history unknown Tape Deck Not Included Video available of working FM and Cassette under extra kart parts youtube channel - message for link Below description found online and buyer must confirm accuracy- reference only - Info from gamma electronics - XYZ Manufacturers Specifications FM Tuner Section: Usable Mono Sensitivity: 10.3 dBf. S/N Ratio: Mono, 75 dB; stereo, 72 dB. THD at 1 kHz: Mono, 0.1%; stereo, 0.2%. Capture Ratio: 1.2 dB. Image Rejection: 45 dB. AM Suppression: 60 dB. Stereo Separation, 1 kHz: 50 dB. Frequency Response: 10 Hz to 15 kHz, +0.2,-1.5 dB. AM Tuner Section: Usable Sensitivity: 15 dB. S/N Ratio: 55 dB. Amplifier Section: Power Output: 40 watts per channel, 8 ohms, 20 Hz to 20 kHz (50 watts, 1 kHz, 4 ohms). THD: 0.02%, 8 ohms. Damping Factor: 80, 1 kHz, 8 ohms. Input Sensitivity: MM phono, 2.5 mV; MC phono, 0.25 mV; high level, 150 mV. Maximum Phono Input Level: MM phono, 200 mV; MC phono, 20 mV. Frequency Response: Phono, RIAA 0.5 dB; high level, 20 Hz to 20 kHz, 0.5 dB. S/N Ratio: MM phono, 80 dB; MC phono, 62 dB; high level, 96 dB. Tone Control Range: 10 dB at 50 Hz and 10 kHz. Subsonic Filter Cutoff: 18 Hz, 6 dB per octave. General Specifications: Power Consumption: 130 watts. Dimensions: 17.1 in. (43.4 cm) W x 4.4 in. (11.2 cm) H x 16.1 in. (40.8 cm) D. Weight: 19.8 lbs. (9.0 kg). Price: $399.95. Company Address: 61 Law Dr., Fairfield, N.J. 07006. As so often happens with advances in audio technology, new features are first incorporated in top-of-the-line separate components which are beyond the reach of all but the most affluent of audio enthusiasts. Later on, these features filter down to high-powered, high-priced all-in-one receiv ers, where a larger audience is potentially available. Finally, they are incorporated into relatively low-cost, medium-powered receivers that just about anyone interested in good sound can afford. The Denon DRA-400 is a good example of a receiver which has benefited from technology first found in higher priced units. This receiver employs crystal-controlled, frequency-synthesized tuning for accuracy and has a five-station preset capability with battery-operated memory backup. Not only does the phono preamplifier section incorporate both moving-magnet and moving-coil inputs (the latter at an input impedance of 100 ohms), but the phono preamp-equalizer section has a direct-coupled input. The power amplifier section employs a non-switching biasing circuit for the elimination of so-called switching and notch distortion at the output stages. These refinements would have been found only on more expensive components just a few years ago. The front panel of the Denon DRA-400 is neatly divided into highly functional upper and lower sections. The upper section contains the power on/off switch, a numeric display of station frequency, a stereo indicator light, a signal-strength LED indicator, up and down tuning buttons, the five preset buttons and their memory switch, program selector pushbuttons, and a large, rotary master-volume control. The signal-strength indicator takes the form of a go-no-go indicator, rather than a signal-strength meter: It lights when the incoming signal strength is deemed adequate and does not light when weaker signals are received-an interesting approach but not very useful. Controls in the lower section are normally covered by a swing-down hinged door, since they are used less frequently than those just described. Behind the door panel are a stereo headphone jack; a pair of speaker selector buttons; bass, treble and balance controls; a three-position monitor/ copy switch; a subsonic filter switch; a stereo/mono switch (associated with FM reception); an MM/MC phono switch, and a loudness on/off switch. The rear panel of the DRA-400 is equipped with the usual 75- and 300-ohm FM antenna terminals, phono and high level input terminals, two pairs of tape in/out jacks, two pairs of color-coded speaker connection terminals, a chassis ground terminal, and a pair of a.c. convenience outlets (one switched, one unswitched). Instead of the usual AM loop stick antenna, a more elaborate, true AM loop antenna is packed with the receiver as a separate item; its two leads must be connected to the appropriate AM and ground terminals on the back of the set. The pivotable loop antenna is best snapped into an antenna holder during receiver installation so the antenna can still be rotated for best AM reception. Since this loop antenna forms part of the input-stage tuned circuit, the owners manual suggests that even if an outdoor AM antenna is used (because of inadequate signal strength), the loop antennas leads should remain connected to their appropriate terminals, in parallel with the outdoor antenna leads. Tuner Measurements Usable mono FM sensitivity fell short of published claims, measuring 16 dBf (3.47 V across 300 ohms). In stereo, sensitivity was limited by muting and stereo thresholds, which were set to 32 dBf (21.9 V). For 50-dB quieting in mono, an input signal strength of 19.5 dBf (5.2 V) was required; for stereo, a signal strength of 42 dBf (69.2 V) was needed. Plots of quieting and distortion (at 1 kHz) versus signal strength are shown in Fig. 1. Signal-to-noise in mono, at 65 dBf of input signal, measured 75 dB as claimed; in stereo it was 72 dB, also exactly as claimed. Harmonic distortion in mono measured 0.17% for a 1-kHz signal, modulating the r.f. carrier by 100%. Total harmonic distortion actually decreased to 0.085% in stereo for the same signal and modulation levels. Distortion in mono and stereo for other audio modulating frequencies is shown in Fig. 2. Although measured distortion was low at high frequencies in stereo and mono, I must point out that these figures were obtained using a bandpass filter with a steep roll-off above 15 kHz (the highest broadcast program frequency). Without the filter, subcarrier products were only some 42 dB below 100% modulation levels.

100% Authentic! All packages are shipped directly from Japan!Condition DescriptionDrive system Direct Drive RPM 33 1/3, 45 rpm Tone arm type AUDIOCRAFT AC-4000MC-S straight type Attached Cartridge AUDIO-TECHNICA AT10G installed (not covered by warranty) Features and Remarks RCA cable included Please Note shipping from Japan. Policy PaymentYou can use various payment methods based on eBay Managed Payments. Import duties, taxes and charges are not included in the item price or shipping charges. These charges are the buyers responsibility.Cancellations & ReturnsCancellation or returns will be accepted only if the item has an obvious problem that was not mentioned in the listing description. If that, please let us know within 3 days you got the item. Buyer is responsible for shipping costs and any charge incurred shipping products back.International BuyersImport duties, taxes and charges are not included in the item price or shipping charges. These charges are the buyers responsibility. Please check with your countrys customs office to determine what these additional costs will be prior to bidding/buying. These charges are normally collected by the delivering freight (shipping) company or when you pick the item up - do not confuse them for additional shipping charges.

Denon DRA 400 Precision Audio Component AM/FM Tuner Stereo AMP Receiver ???? Works. Condition is Used. Shipped with USPS Ground Advantage.

Denon DRA 400 Precision Audio Component AM/FM Tuner Stereo AMP Receiver Used, works - Bought at an estate sale, history unknown Tape Deck Not Included Video available of working FM and Cassette under extra kart parts youtube channel - message for link Below description found online and buyer must confirm accuracy- reference only - Info from gamma electronics - XYZ Manufacturers Specifications FM Tuner Section: Usable Mono Sensitivity: 10.3 dBf. S/N Ratio: Mono, 75 dB; stereo, 72 dB. THD at 1 kHz: Mono, 0.1%; stereo, 0.2%. Capture Ratio: 1.2 dB. Image Rejection: 45 dB. AM Suppression: 60 dB. Stereo Separation, 1 kHz: 50 dB. Frequency Response: 10 Hz to 15 kHz, +0.2,-1.5 dB. AM Tuner Section: Usable Sensitivity: 15 dB. S/N Ratio: 55 dB. Amplifier Section: Power Output: 40 watts per channel, 8 ohms, 20 Hz to 20 kHz (50 watts, 1 kHz, 4 ohms). THD: 0.02%, 8 ohms. Damping Factor: 80, 1 kHz, 8 ohms. Input Sensitivity: MM phono, 2.5 mV; MC phono, 0.25 mV; high level, 150 mV. Maximum Phono Input Level: MM phono, 200 mV; MC phono, 20 mV. Frequency Response: Phono, RIAA 0.5 dB; high level, 20 Hz to 20 kHz, 0.5 dB. S/N Ratio: MM phono, 80 dB; MC phono, 62 dB; high level, 96 dB. Tone Control Range: 10 dB at 50 Hz and 10 kHz. Subsonic Filter Cutoff: 18 Hz, 6 dB per octave. General Specifications: Power Consumption: 130 watts. Dimensions: 17.1 in. (43.4 cm) W x 4.4 in. (11.2 cm) H x 16.1 in. (40.8 cm) D. Weight: 19.8 lbs. (9.0 kg). Price: $399.95. Company Address: 61 Law Dr., Fairfield, N.J. 07006. As so often happens with advances in audio technology, new features are first incorporated in top-of-the-line separate components which are beyond the reach of all but the most affluent of audio enthusiasts. Later on, these features filter down to high-powered, high-priced all-in-one receiv ers, where a larger audience is potentially available. Finally, they are incorporated into relatively low-cost, medium-powered receivers that just about anyone interested in good sound can afford. The Denon DRA-400 is a good example of a receiver which has benefited from technology first found in higher priced units. This receiver employs crystal-controlled, frequency-synthesized tuning for accuracy and has a five-station preset capability with battery-operated memory backup. Not only does the phono preamplifier section incorporate both moving-magnet and moving-coil inputs (the latter at an input impedance of 100 ohms), but the phono preamp-equalizer section has a direct-coupled input. The power amplifier section employs a non-switching biasing circuit for the elimination of so-called switching and notch distortion at the output stages. These refinements would have been found only on more expensive components just a few years ago. The front panel of the Denon DRA-400 is neatly divided into highly functional upper and lower sections. The upper section contains the power on/off switch, a numeric display of station frequency, a stereo indicator light, a signal-strength LED indicator, up and down tuning buttons, the five preset buttons and their memory switch, program selector pushbuttons, and a large, rotary master-volume control. The signal-strength indicator takes the form of a go-no-go indicator, rather than a signal-strength meter: It lights when the incoming signal strength is deemed adequate and does not light when weaker signals are received-an interesting approach but not very useful. Controls in the lower section are normally covered by a swing-down hinged door, since they are used less frequently than those just described. Behind the door panel are a stereo headphone jack; a pair of speaker selector buttons; bass, treble and balance controls; a three-position monitor/ copy switch; a subsonic filter switch; a stereo/mono switch (associated with FM reception); an MM/MC phono switch, and a loudness on/off switch. The rear panel of the DRA-400 is equipped with the usual 75- and 300-ohm FM antenna terminals, phono and high level input terminals, two pairs of tape in/out jacks, two pairs of color-coded speaker connection terminals, a chassis ground terminal, and a pair of a.c. convenience outlets (one switched, one unswitched). Instead of the usual AM loop stick antenna, a more elaborate, true AM loop antenna is packed with the receiver as a separate item; its two leads must be connected to the appropriate AM and ground terminals on the back of the set. The pivotable loop antenna is best snapped into an antenna holder during receiver installation so the antenna can still be rotated for best AM reception. Since this loop antenna forms part of the input-stage tuned circuit, the owners manual suggests that even if an outdoor AM antenna is used (because of inadequate signal strength), the loop antennas leads should remain connected to their appropriate terminals, in parallel with the outdoor antenna leads. Tuner Measurements Usable mono FM sensitivity fell short of published claims, measuring 16 dBf (3.47 V across 300 ohms). In stereo, sensitivity was limited by muting and stereo thresholds, which were set to 32 dBf (21.9 V). For 50-dB quieting in mono, an input signal strength of 19.5 dBf (5.2 V) was required; for stereo, a signal strength of 42 dBf (69.2 V) was needed. Plots of quieting and distortion (at 1 kHz) versus signal strength are shown in Fig. 1. Signal-to-noise in mono, at 65 dBf of input signal, measured 75 dB as claimed; in stereo it was 72 dB, also exactly as claimed. Harmonic distortion in mono measured 0.17% for a 1-kHz signal, modulating the r.f. carrier by 100%. Total harmonic distortion actually decreased to 0.085% in stereo for the same signal and modulation levels. Distortion in mono and stereo for other audio modulating frequencies is shown in Fig. 2. Although measured distortion was low at high frequencies in stereo and mono, I must point out that these figures were obtained using a bandpass filter with a steep roll-off above 15 kHz (the highest broadcast program frequency). Without the filter, subcarrier products were only some 42 dB below 100% modulation levels.

Denon POA-4400A POWER AMPLIFIER / ENDSTUFE + Equalizer. 2 1m xlr chinch vandenhul silberkabel + 25m chinch vandenhul silberkabel . Top Zustand Bei Rckfragen Olaf Hartmann 015738127741 zwischen 16:00 - 20:00 Uhr Da privat verkauf keine Garantie und rcknahme.