Beschreibung
The HDMI doesnt work. Itll go into standby mode if you use bluray player mode, and shuts off after a few minutes when using the other inputs. Ostensibly the analog outputs should work, but Im not going to bother testing them. Includes the original remote (clean battery compartment) and original box. The manual is already available online, just use that one. Copy paste of specs from the Sonys manual: Specifications AUDIO POWER SPECIFICATIONS POWER OUTPUT AND TOTAL HARMONIC DISTORTION: (USA model only) With 8 ohm loads, both channels driven, from 20 – 20,000 Hz; rated 90 watts per channel minimum RMS power, with no more than 0.09% total harmonic distortion from 250 milliwatts to rated output. Amplifier section USA model1) Minimum RMS Output Power (8 ohms, 20 Hz – 20 kHz, THD 0.09%) 90 W + 90 W Stereo Mode Output Power (8 ohms, 1 kHz, THD 1%) 100 W + 100 W Surround Mode Output Power2) (8 ohms, 1 kHz, THD 10%) 130 W per channel Canada, Europe, Australia and Taiwan models1) Minimum RMS Output Power (8 ohms, 20 Hz – 20 kHz, THD 0.09%) 85 W + 85 W Stereo Mode Output Power (8 ohms, 1 kHz, THD 1%) 100 W + 100 W Surround Mode Output Power2) (8 ohms, 1 kHz, THD 10%) 130 W per channel 1)Measured under the following conditions: 2)Reference power output for front, center, surround, surround back and front high speakers. Depending on the sound field settings and the source, there may be no sound output. Frequency response Analog 10 Hz – 70 kHz, +0.5/–2 dB (with sound field and equalizer bypassed) Input Analog (PORTABLE IN) Sensitivity: 1 V/50 kohms S/N3) : 96 dB (A, 500 mV 4) ) Analog (Except PORTABLE IN) Sensitivity: 500 mV/ 50 kohms S/N3) : 96 dB (A, 500 mV 4) ) Digital (Coaxial) Impedance: 75 ohms S/N: 100 dB (A, 20 kHz LPF) Digital (Optical) S/N: 100 dB (A, 20 kHz LPF) Output (Analog) AUDIO OUT Voltage: 500 mV/1 kohm SUBWOOFER Voltage: 2 V/1 kohm Equalizer Gain levels ±10 dB, 1 dB step 3)INPUT SHORT (with sound field and equalizer bypassed). 4)Weighted network, input level. FM tuner section Tuning range 87.5 MHz – 108.0 MHz Antenna (aerial) FM wire antenna (aerial) Antenna (aerial) terminals 75 ohms, unbalanced Intermediate frequency 10.7 MHz AM tuner section Tuning range Antenna (aerial) Loop antenna (aerial) Intermediate frequency 450 kHz Area Power requirements USA, Canada, Taiwan 120 V AC, 60 Hz Europe, Australia 230 V AC, 50 Hz Area Tuning scale 10 kHz step 9 kHz step USA, Canada 530 kHz – 1,710 kHz 531 kHz – 1,710 kHz Europe, Australia, Taiwan – 531 kHz – 1,602 kHz continued 70GB Video section Inputs/Outputs Video: 1 Vp-p, 75 ohms COMPONENT VIDEO: Y: 1 Vp-p, 75 ohms P B : 0.7 Vp-p, 75 ohms P R : 0.7 Vp-p, 75 ohms 80 MHz HD Pass Through General Power requirements Power consumption 240W Power consumption (during standby mode) 0.3 W (When “CTRL.HDMI” is set to “CTRL OFF”) Dimensions (width/height/depth) (Approx.) 430 mm × 157.5 mm × 322 mm (17 in × 6 1/4 in × 12 3/4 in) including projecting parts and controls Mass (Approx.) 7.6 kg (16 lb 13 oz) Design and specifications are subject to change without notice. Area Power requirements USA, Canada, Taiwan 120 V AC, 60 Hz Europe, Australia 230 V AC, 50/60 Hz Halogenated flame retardants are not used in the certain printed wiring boards.
Livesuche