For the audiophiles all over the world ORTOFON products reach legendary status. And thats rightfully. This is a opportunity to own whats becoming rare and more expensive on the world market. Excellent tonearm for serious music lovers ********************Broadcast Tonearm Ortofon AB -309 banana 12 long for Ortofon SPU-G and SME type Headshells ONE OF THE BEST 12 LONG TONEARMSMADE BY ALFRED BOKRANDGERMAN BROADCAST ENGINEER(RADIO+TV) WHY?PHYSICS and GEOMETRY never lies.....THIS ARMWAND IS OPTIMIZED FORLOWEST TRACKING DISTORSION3 THINGS DETERMINE THE QUALITY AND THE PERFORMANCE OF A PERFECT TONEARM:1) EFFEKTIVE LENGHT 2) OVERHANG3) OFFSET ANGLE============================ TONEARM GEOMETRY:EFFEKTIVE LENGTH : 321.459 mm MOUNTING DISTANCE: 309.4mmOVERHANG: 12.66 mmOFFSET ANGLE (DEGREES): 16.9 º _____________________________________________________________========================== ORTOFON 12 AS-309 TONEARM HAVE LESS DISTORSIONS AS THE SME 3012 series I ORTOFON AS-309 12 long compared to SME 3012 series I 309.4 mm mounting distance 294 mm 321.5 mm effektive lenght 305 mm 12.6 mm Over hang 11 mm 16.9 º offset angle(degrees) 16.15 º 1.26 º maximum error º 2.11 º 0.3 % average distorsion 0.36 % 0.46 % maximum distorsion 0.72 % all results taken fromAlignment Calculator Provinylengine page Tonearm geometry with the lowest distortion worldwide, you will hear it immediately the geometry had to be calculated by hand in the 60s, because you did not have any computer calculation programs yet, this could never be the optimum, because the 3 parameters for the geometry are interdependent. When you change only one parameter to 0.5mm the distortions are great. Therefore, tonearms from the 60s can NEVER reach the perfection that is possible with the computer programs today___________________________________This tonearm combines the simple aesthetics of Ortofon Tonearms with the current best armtube geometry currently available only a perfect geometry of the armtube guarantees a low distortion.this is the first and most important thing with a tonearm.not the material, not exotic armtube materials or mimics can eliminate a fundamental distortion that exist due to a wrong and bad geometry.material of the armtube and Vaccination only has an impact on resonance and vibration coming from the plinth (engine vibration and music waves) tonal arms are offered on the market, which cost well over $ 15,000 and are advertised that give the materials the highest in technology (space travel, NASA ect) the geometry of a perfect tonearm with the lowest distorsions consists of: 1) effective length2) overhang3) offset angle nothing more and nothing less these 3 parameters are dependent on each other. This is mathematics and is based on formulas that have absolutely nothing to do with materials. With existing PC calculation programs, anyone can see if their tonearm has the least distortion due to the armtube geometry. This is the only objective method and not the subjective belief in exotic materials or great promises..**************************************************************** positive feedbacks Aligned. It is in an aftermarket VTA tower made for the Groovmaster IIti that was on the table before your arm. I will not going back to the GM!!! Only my $11,000 Glanz MH124 is superior and not by $10,000! I am thrilled at this arms performance richness of tone is its major strong point. Bass is tight super extended and the too end extended and sweet. No ringing or tonal artifacts with this arm. Vocals are on par with the best of the best. Rich defined and harmonical. Thank you sir. Well done! Robin WyattMiyajima Labs USA importer. _______________________________ My Ortofon tonearms go over the SME 3012 and SME 3012R, which costs about 5000 euros. It is only surpassed by a GLANZ for $11,000. Thats not what Im saying, but my customers.see here original mailsDear mr. BokrandI gave myself some time to make sure I wasn’t too hasty in judging. After many hours of listening to my favorite records, which I know very well, I can say that your arm holds up very well the comparison with my beloved SME 3012R, indeed, with the Ortofon SPU is superior in clarity, dynamics (!!!), soundness of bass...Thanks for everythingMassimo Longoni________________________________________________________________________ screw for setting Azimuth 2 DIFFERENT COUNTER WEIGHTS 2 WEIGHTS TOGETHER FOR ORTOFON SPU-G CARTRIDGS UP TO 35 GRAMS or BIG COUNTER WEIGHT SINGLY FOR CARTRIDGES UP TO 20 GRAMS With this construction you have an enormous range of applications for all Cartridges _________________________________________________ liftlever is modified by me in the vintage Ortofon style like the Ortofon Hi Jack.I like this classic timeless style ******************************** TONEARM COMES WITH :MOUNTING TEMPLATEMANUALSCREWS AND WASHERS FOR MOUNTING COLLARALLEN KEY FOR ADJUST LIFT DEVICESCREW DRIVER FOR WEIGHTSSCREW DRIVER FOR AZIMUTH ADJUST in the manual you will always find an original sample of the internal wiring WORLDWIDE FREE SHIPPINGTRACKING AND REGISTERED POST------------------------------------------- reviews from customers( Original text e-mails) from HiFi Wigwam:The Ortofon arm is one of the ones off ebay done by a German guy in Spain (Alfred Bokrand), based on the old (Danish-made) Ortofon AS212/309 bearing housing and anti-skate mechanism, with an arm tube and weights of his own design. I think its a wonderful bit of kit, I prefer it to the Thomas Schick arm that I used to have, which I had bias problems with, this is properly adjustable. Its a ridiculous bargain for the £500 or so hes charging for it. This 301 has a very special tonearm. It was made by Alfred Bokrand from an Ortofon AS-212 on which he has placed a 12? wand. The workmanship is first class and it tracks like a dream. This model of Ortofon arm is known for its pivot set up- it has wonderful bearings, it has a two part counter weight that will allow for a SPU with built in transformer......============================================================== Dear Alfred. I finally set up the tonearm and I am more than satisfied with the results. It has been a huge improvement in my musical experience. The tonearm is piece of beauty and perfect enginered for music reproduction. The classical records sound heavenly good and Jazz albums never as intimate. The severe wrapped records do never miss the track. The bass response is clean and solid. Great. Thanks for your patience with my issues and I am very grateful for send me another cable. Happy new year Afectuosamente Ignacio Enviado desde mi iPhone (email from 28.12.2016)Hi Alfred Just letting you know that the tonearm arrived safe and sound.I have installed it on a 16 broadcast turntable and it sounds great (and looks good as well). Thank you very much. Wolfgang (email from 30.12.2016) Hello Alfred, I have been wanting to tell you that I have been enjoying your tonearm so very much ! The set up was easy, thank you for the template and alignment tool, it is very precise. The quality of the tonearm is excellent, of course, and I have already found the split counterweight very useful. I have been trying the arm with a Denon 103 and an Ikeda 9C cartridge, and both sound wonderful. The Ikeda requires much more attention to alignments, and your tonearm makes that very simple. It is also nice to have the anti skate adjustment too, which helps a lot with the ikeda. More than anything, Im enjoying music, which is more important than any technicalities. I will send you photos soon of my turntable setup so you may see everything in its happy state. My turntable is a Garrard 401. With many thanks again, in gratitude for your fine work and dedication, S.M New York 17.Sept. 2014 Hallo Alfred, es ist vollbracht. In ca. 3 Tagen habe ich die Zarge für den Neuen aufgebaut.Die ersten Platten drehen sich seit gestern auf dem Ortofon-Bokrand Sp-15.Schon erstaunlich was da aus meinen Eckhörnern kommt.Ich kann ihn nur mit meinem EMT 948 vergleichen mit dem ich seit ca. 1 Jahr sehr intensiv höre.Ich hab das Gefühl, dass das Gespann des Neuen sehr nahe an Perfektion ist und das für ca. 1/3 des Preises des 948!Vielen Dank für deine tolle Arbeit an dem Tonarm! Thomas K.(Germany) 28.12.2012 ORTOFON 12 long with TECHNICS SP-15 from Thomas K. Hi Alfred. I have been using this tone arm with my Garrard 301 / mono Ortofon Spu cartridge. It sounds absolutely superb. I must congratulate you on your fine work. Have you had a chance to post the Ortofon Head shell yet? I am looking forward to using this with my Shure V15mxr cartridge. Many thanks. John ----- Original Message -----Sent: Tuesday, August 14, 2012 6:23 PM Subject: AW: Re: Ortofon Tone Arm Dear Alfred I have finally set up the tonearm and listened to LPs with it. I have to say that it is better than some of my other arms, possibly because of the strong arm tube.(FROM FSK HONG KONG)Hi Alfred, Glad to tell you that I have received and installed the tonearm after some hard work. Sound is great ! Still take some time for the cartridge to break-in but the tracking ability is extraordinary which allows any music to sing beautifully. Otherwise, it seems perfect to me. Thank you for your help ! Hi Alfred, The system actually sounds better and better from day to day. Impressive particular for old LPs. While writing to you, I am listening to the original Moon River of Andy William. The Exdous Song has never sound so good before - Superb !(Original text email from Japan)Dear Alfred I have at last set up your arm and can now give you an early impression of the sound. Beautifully balanced throughout the frequency range, no irritating frequencies stand out. Air and focus are superb. It is very musical with excellent pitch. Tonal range is very even handed and smooth. However the overall feeling is best summed up by saying that it sounds right in particular piano takes on the feel of one you have grown to recognise from your days in school plays.(Original text of the email from UK)---------------------------------------------------------------------Hello Alfred, I received the new cable yesterday afternoon.Thank you very much for your fast and kindly support.At last, I was able to listen to the sound of your special tonearm. WOW ! Excellent !! I love it.I always use DENON DL103-LC2(?? as a standard cartridgetesting the change of the sound. It was still the result of the short time test, but I felt the sound wassplendid.Lower background-noise, wide and deep sound-stage, particularlythe sonority is very natural and clear.(original mail from Mr.T. Japan)_______________________________________________________ Good morning Alfred, Well, yesterday I mounted your arm on the plinth with the SPU Meister Silver. Mounting was a breeze using my tool for determining the spindle to pivot distance. Using the dual counterweight it is also very easy to tune for optimal stylus pressure, at least far more easy than when using one counterweight. So that is a practical plus for the dual counterweights above the ability for mounting less heavy cartridges as well.I asked you before how your tonearm would compare to the Schick and you were modest. No need to! It is so much better than the Schick when using the heavy SPU.. really, it performs better on from low up to the high frequencies. I have been listening, or actually rediscovering, lots of records sinds yesterday afternoon. I always found that the SPU had at some records a bit of harsh highs but these are completely gone now. So that must have been the combination with the Schick, is my guess. Resonances are way better suppressed now and I do believe that the heavy and sturdy construction does not allow for any other movement of the cartridge/needle than lateral movement.I bow deep for your expertise as that must be the basis of the reconstructed Ortofon! We are really impressed here! My suggestion is that I buy two more arms from you. So I keep the one that is on my turntable now and you send over two complete tonearms. These two consist of the one that you customised for me and another one.I want to replace the Schick with a second AB309 and the third will be for a friend who started dancing in my room when he heard your tonearm..So all together:1. I will keep the tonearm I currently have. This one will go to my friend as he likes the J-shaped armtube.2. The customised arm by you, complete with mounting stuff and counterweights, will replace the one that will go to my friend.3. The third tonearm will replace the Schick tonearm on my plinth. So that is a whole new arm.DHT Rob Netherland 02/12/2018 pictures received from satisfied customers IF YOU ARE NOT SATISFIED,MONEY BACK GUARANTEE***************************************

For sale phono cable for EMT 929, 997 and old Ortofon 229, 297, 309 tonearms.Lenght 1,25m. (For different lengths please ask.) -NEW Neutrik/Rean NYS 373 RCA connectors-NEW CORDIAL CMK-422 GERMANY copper balanced cable. (Capacity cond. 66 pF/m )-NEW/NOS 7-pin connector

Condition DescriptionUsed (no noticeable scratches or stains) There is no noticeable damage on the whole and it is beautiful with luster / luster. ? Operation? We have confirmed the operation of our equipment. ?Output from both channels ? Each adjustment point, operation feeling ?Height adjustment, etc. There is no problem in operation. ?Accessories ?Arm stand ?Stand fixing screw x 3 ?Armrest ?Mounting nut/washer for rest ?PHONO cable ?Instruction manual (copy) ?Mounting template (copy) Please Note shipping from Japan. Policy PaymentWe can shipping only registered address on ebay. Import duties, taxes and charges are not included in the item price or shipping charges. These charges are the buyers responsibility.ShippingI send a product by International Priority(FedEx or UPS) or EMS(Japan Post) . I will determine the required shipping company depending on the situation. I attach the tracking number. Please bid it without worrying. Shipping is only available to the address registered in eBay. Please note that any address not registered in eBay is not acceptable to ship. Shipping is available from Monday to Friday. Weekends are not available because post office is closed.Terms of SaleImport duties, taxes and charges are not included in the item price or shipping charges. These charges are the buyers responsibility. Please check with your countrys customs office to determine what these additional costs will be prior to Unconditional Return Policy Customer service and satisfaction are very important to us. I have an unconditional return policy if notified within 30 of the receipt of the item. All returned items must be the original condition. All return requests must be made within 30 days of the receipt of the item. Please contact me first for return before you ship it back to me.International BuyersImport duties, taxes and charges are not included in the item price or shipping charges. These charges are the buyers responsibility. Please check with your countrys customs office to determine what these additional costs will be prior to bidding/buying. These charges are normally collected by the delivering freight (shipping) company or when you pick the item up - do not confuse them for additional shipping charges.

ortofon AS-309S Static Balance Type 12” Long Tonearm Pickup Arm Analog Audio Domo Arigato! Welcome, Thank you for your visit. Description Operation confirmed. The appearance is a beautiful product without any noticeable scratches. For other appearances, please refer to the photo. *The wooden pedestal in the photo is for photographic purposes only and is not included in the product. Specifications Effective length: 311mm (with SPU: 315mm)?Overhang: 15mm?Stylus adjustment range: 0 to 3g?Compatible weight: 18 to 28g (including shell)?Weight: 545g Shipping Shipping is only available to the address registered in eBay. Shipping is by FedEx or EMS. Free Shipping Returns Unconditional Return Policy Customer service and satisfaction are very important to us.I have an unconditional return policy if notified within 30 of the receipt of the item. All returned items must be the original condition.All return requests must be made within 30 days of the receipt of the item. Please contact me first for return before you ship it back to me.The postage of the returned goods is a buyer burden. International Buyers Please Note:Import duties, taxes and charges are not included in the item price or shipping charges.These charges are the buyer?s responsibility.Please check with your country?s customs office to determine what these additional costs will be prior to bidding/buying.These charges are normally collected by the delivering freight (shipping) company or when you pick the item up -do not confuse them for additional shipping charges.We do not mark merchandise values below value or mark items as ?gifts? -US and International government regulations prohibit such behavior. I am sorry but we can not arrange that because it is illegal in Japan.Thank you.

ortofon RMG309 Dynamic Balance Type Long Tonearm Pickup Arm for SPU G Shell Domo Arigato! Welcome, Thank you for your visit. Description Overhauled by a specialist.Resin parts of the weight shaft have been replaced. Other parts shown in the 9th photo have been replaced.Sound output has been checked. All movements are smooth and there is no sticking of the weight adjustment dial. The appearance is a beautiful product without any noticeable scratches. Accessories Phono cable (genuine type) x 1Straight plug 5P (1300mm long) using Western Electric wire and Switchcraft RCA terminals.AL1 tone arm lifter. Shipping Shipping is only available to the address registered in eBay. Shipping is by FedEx or EMS. Free Shipping Returns Unconditional Return Policy Customer service and satisfaction are very important to us.I have an unconditional return policy if notified within 30 of the receipt of the item. All returned items must be the original condition.All return requests must be made within 30 days of the receipt of the item. Please contact me first for return before you ship it back to me.The postage of the returned goods is a buyer burden. International Buyers Please Note:Import duties, taxes and charges are not included in the item price or shipping charges.These charges are the buyer’s responsibility.Please check with your country’s customs office to determine what these additional costs will be prior to bidding/buying.These charges are normally collected by the delivering freight (shipping) company or when you pick the item up -do not confuse them for additional shipping charges.We do not mark merchandise values below value or mark items as “gifts” -US and International government regulations prohibit such behavior. I am sorry but we can not arrange that because it is illegal in Japan.Thank you.

Ricambi originali ortofon TypeD Opzionale Peso per braccio / SPU AS-309S Cartuccia Domo Arigato! Benvenuto, grazie per la tua visita. Descrizione Operazione confermata. Laspetto è un bellissimo prodotto senza graffi evidenti. Questo peso opzionale è necessario quando si utilizzano cartucce pesanti come la serie Ortofon SPU con il braccio Ortofon AS-309S. Specifica Peso: 249 g?Peso compatibile: 26-38 g (compreso guscio) Spedizione La spedizione è disponibile solo per lindirizzo registrato su eBay. La spedizione è entro Fedex O SME. Spedizione gratuita ritorna Politica di restituzione incondizionata Il servizio e la soddisfazione del cliente sono molto importanti per noi.Ho una politica di restituzione incondizionata se notificata entro 30 giorni dalla ricezione dellarticolo. Tutti gli articoli restituiti devono essere nella condizione originale.Tutte le richieste di reso devono essere effettuate entro 30 giorni dal ricevimento dellarticolo. Per favore contattami prima per il reso prima di rispedirmelo.Le spese di spedizione della merce restituita sono a carico dellacquirente. Acquirenti internazionali Notare che:I dazi doganali, le tasse e le spese non sono inclusi nel prezzo dellarticolo o nelle spese di spedizione.Queste spese sono a carico dellacquirente.Si prega di verificare con lufficio doganale del proprio paese per determinare quali saranno questi costi aggiuntivi prima dellofferta/acquisto.Queste spese vengono normalmente riscosse dalla società di spedizione (spedizione) o al momento del ritiro dellarticolo: non confonderle con spese di spedizione aggiuntive.Non contrassegniamo i valori della merce al di sotto del valore né contrassegniamo gli articoli come regali? -Le normative governative statunitensi e internazionali vietano tale comportamento. Mi dispiace, ma non possiamo organizzarlo perché è illegale in Giappone.Grazie.

ortofon Genuine Parts TypeD Optional Weight for AS-309S Tonearm / SPU Cartridge Domo Arigato! Welcome, Thank you for your visit. Description Operation confirmed. The appearance is a beautiful product without any noticeable scratches. This optional weight is required when using heavy cartridges such as the Ortofon SPU series with the Ortofon tone arm AS-309S. Specification Weight: 249g?Compatible weight: 26-38g (including shell) Shipping Shipping is only available to the address registered in eBay. Shipping is by FedEx or EMS. Free Shipping Returns Unconditional Return Policy Customer service and satisfaction are very important to us.I have an unconditional return policy if notified within 30 of the receipt of the item. All returned items must be the original condition.All return requests must be made within 30 days of the receipt of the item. Please contact me first for return before you ship it back to me.The postage of the returned goods is a buyer burden. International Buyers Please Note:Import duties, taxes and charges are not included in the item price or shipping charges.These charges are the buyer?s responsibility.Please check with your country?s customs office to determine what these additional costs will be prior to bidding/buying.These charges are normally collected by the delivering freight (shipping) company or when you pick the item up -do not confuse them for additional shipping charges.We do not mark merchandise values below value or mark items as ?gifts? -US and International government regulations prohibit such behavior. I am sorry but we can not arrange that because it is illegal in Japan.Thank you.

ortofon RMG309 Braccio pickup con bilanciamento dinamico tipo lungo per SPU G Shell Domo Arigato! Benvenuto, grazie per la tua visita. Descrizione Revisionato da uno specialista.Le parti in resina dellalbero pesi sono state sostituite. Altre parti mostrate nella nona foto sono state sostituite.Luscita audio è stata controllata. Tutti i movimenti sono fluidi e non vi è alcun inceppamento del quadrante di regolazione del peso. Laspetto è un bellissimo prodotto senza graffi evidenti. Accessori Cavo fono (tipo originale) x 1Spina diritta 5P (lunga 1300 mm) utilizzando cavo Western Electric e terminali RCA Switchcraft.Sollevatore per braccio AL1. Spedizione La spedizione è disponibile solo per lindirizzo registrato su eBay. La spedizione è entro Fedex O SME. Spedizione gratuita ritorna Politica di restituzione incondizionata Il servizio e la soddisfazione del cliente sono molto importanti per noi.Ho una politica di restituzione incondizionata se notificata entro 30 giorni dalla ricezione dellarticolo. Tutti gli articoli restituiti devono essere nella condizione originale.Tutte le richieste di reso devono essere effettuate entro 30 giorni dal ricevimento dellarticolo. Per favore contattami prima per il reso prima di rispedirmelo.Le spese di spedizione della merce restituita sono a carico dellacquirente. Acquirenti internazionali Notare che:I dazi doganali, le tasse e le spese non sono inclusi nel prezzo dellarticolo o nelle spese di spedizione.Queste spese sono a carico dellacquirente.Si prega di verificare con lufficio doganale del proprio paese per determinare quali saranno questi costi aggiuntivi prima dellofferta/acquisto.Queste spese vengono normalmente riscosse dalla società di spedizione (spedizione) o al momento del ritiro dellarticolo: non confonderle con spese di spedizione aggiuntive.Non contrassegniamo i valori della merce al di sotto del valore né contrassegniamo gli articoli come regali: le normative governative statunitensi e internazionali vietano tale comportamento. Mi dispiace, ma non possiamo organizzarlo perché è illegale in Giappone.Grazie.

ortofon AS-309S Static Balance Type 12” Long Tonearm Pickup Arm Analog Audio Domo Arigato! Welcome, Thank you for your visit. Description Operation confirmed. The appearance is a beautiful product without any noticeable scratches. For other appearances, please refer to the photo. *The wooden pedestal in the photo is for photographic purposes only and is not included in the product. Specifications Effective length: 311mm (with SPU: 315mm)?Overhang: 15mm?Stylus adjustment range: 0 to 3g?Compatible weight: 18 to 28g (including shell)?Weight: 545g Shipping Shipping is only available to the address registered in eBay. Shipping is by FedEx or EMS. Free Shipping Returns Unconditional Return Policy Customer service and satisfaction are very important to us.I have an unconditional return policy if notified within 30 of the receipt of the item. All returned items must be the original condition.All return requests must be made within 30 days of the receipt of the item. Please contact me first for return before you ship it back to me.The postage of the returned goods is a buyer burden. International Buyers Please Note:Import duties, taxes and charges are not included in the item price or shipping charges.These charges are the buyer?s responsibility.Please check with your country?s customs office to determine what these additional costs will be prior to bidding/buying.These charges are normally collected by the delivering freight (shipping) company or when you pick the item up -do not confuse them for additional shipping charges.We do not mark merchandise values below value or mark items as ?gifts? -US and International government regulations prohibit such behavior. I am sorry but we can not arrange that because it is illegal in Japan.Thank you.

Selling for restoration Rare ortofon rf-309 mono tonearm with esL ortofon spu cartridge Item has not been tested Stylus tip is worn Please check all pictures provided Selling for restoration No warranty’s or returns

For sale phono cable for EMT 929, 997 and old Ortofon 229, 297, 309 tonearms.Lenght 1,25m. (For different lengths please ask.) -NEW Neutrik/Rean NYS 373 RCA connectors-NEW CORDIAL CMK-422 GERMANY copper balanced cable. (Capacity cond. 66 pF/m )-NEW/NOS 7-pin connector

For the audiophiles all over the world ORTOFON products reach legendary status. And thats rightfully. This is a opportunity to own whats becoming rare and more expensive on the world market. Excellent tonearm for serious music lovers ********************Broadcast Tonearm Ortofon AB -309 banana 12 long for Ortofon SPU-G and SME type Headshells ONE OF THE BEST 12 LONG TONEARMSMADE BY ALFRED BOKRANDGERMAN BROADCAST ENGINEER(RADIO+TV) WHY?PHYSICS and GEOMETRY never lies.....THIS ARMWAND IS OPTIMIZED FORLOWEST TRACKING DISTORSION3 THINGS DETERMINE THE QUALITY AND THE PERFORMANCE OF A PERFECT TONEARM:1) EFFEKTIVE LENGHT 2) OVERHANG3) OFFSET ANGLE============================ TONEARM GEOMETRY:EFFEKTIVE LENGTH : 321.459 mm MOUNTING DISTANCE: 309.4mmOVERHANG: 12.66 mmOFFSET ANGLE (DEGREES): 16.9 º _____________________________________________________________========================== ORTOFON 12 AS-309 TONEARM HAVE LESS DISTORSIONS AS THE SME 3012 series I ORTOFON AS-309 12 long compared to SME 3012 series I 309.4 mm mounting distance 294 mm 321.5 mm effektive lenght 305 mm 12.6 mm Over hang 11 mm 16.9 º offset angle(degrees) 16.15 º 1.26 º maximum error º 2.11 º 0.3 % average distorsion 0.36 % 0.46 % maximum distorsion 0.72 % all results taken fromAlignment Calculator Provinylengine page Tonearm geometry with the lowest distortion worldwide, you will hear it immediately the geometry had to be calculated by hand in the 60s, because you did not have any computer calculation programs yet, this could never be the optimum, because the 3 parameters for the geometry are interdependent. When you change only one parameter to 0.5mm the distortions are great. Therefore, tonearms from the 60s can NEVER reach the perfection that is possible with the computer programs today___________________________________This tonearm combines the simple aesthetics of Ortofon Tonearms with the current best armtube geometry currently available only a perfect geometry of the armtube guarantees a low distortion.this is the first and most important thing with a tonearm.not the material, not exotic armtube materials or mimics can eliminate a fundamental distortion that exist due to a wrong and bad geometry.material of the armtube and Vaccination only has an impact on resonance and vibration coming from the plinth (engine vibration and music waves) tonal arms are offered on the market, which cost well over $ 15,000 and are advertised that give the materials the highest in technology (space travel, NASA ect) the geometry of a perfect tonearm with the lowest distorsions consists of: 1) effective length2) overhang3) offset angle nothing more and nothing less these 3 parameters are dependent on each other. This is mathematics and is based on formulas that have absolutely nothing to do with materials. With existing PC calculation programs, anyone can see if their tonearm has the least distortion due to the armtube geometry. This is the only objective method and not the subjective belief in exotic materials or great promises..**************************************************************** positive feedbacks Aligned. It is in an aftermarket VTA tower made for the Groovmaster IIti that was on the table before your arm. I will not going back to the GM!!! Only my $11,000 Glanz MH124 is superior and not by $10,000! I am thrilled at this arms performance richness of tone is its major strong point. Bass is tight super extended and the too end extended and sweet. No ringing or tonal artifacts with this arm. Vocals are on par with the best of the best. Rich defined and harmonical. Thank you sir. Well done! Robin WyattMiyajima Labs USA importer. _______________________________ My Ortofon tonearms go over the SME 3012 and SME 3012R, which costs about 5000 euros. It is only surpassed by a GLANZ for $11,000. Thats not what Im saying, but my customers.see here original mailsDear mr. BokrandI gave myself some time to make sure I wasn’t too hasty in judging. After many hours of listening to my favorite records, which I know very well, I can say that your arm holds up very well the comparison with my beloved SME 3012R, indeed, with the Ortofon SPU is superior in clarity, dynamics (!!!), soundness of bass...Thanks for everythingMassimo Longoni________________________________________________________________________ screw for setting Azimuth 2 DIFFERENT COUNTER WEIGHTS 2 WEIGHTS TOGETHER FOR ORTOFON SPU-G CARTRIDGS UP TO 35 GRAMS or BIG COUNTER WEIGHT SINGLY FOR CARTRIDGES UP TO 20 GRAMS With this construction you have an enormous range of applications for all Cartridges _________________________________________________ liftlever is modified by me in the vintage Ortofon style like the Ortofon Hi Jack.I like this classic timeless style ******************************** TONEARM COMES WITH :MOUNTING TEMPLATEMANUALSCREWS AND WASHERS FOR MOUNTING COLLARALLEN KEY FOR ADJUST LIFT DEVICESCREW DRIVER FOR WEIGHTSSCREW DRIVER FOR AZIMUTH ADJUST in the manual you will always find an original sample of the internal wiring WORLDWIDE FREE SHIPPINGTRACKING AND REGISTERED POST------------------------------------------- reviews from customers( Original text e-mails) from HiFi Wigwam:The Ortofon arm is one of the ones off ebay done by a German guy in Spain (Alfred Bokrand), based on the old (Danish-made) Ortofon AS212/309 bearing housing and anti-skate mechanism, with an arm tube and weights of his own design. I think its a wonderful bit of kit, I prefer it to the Thomas Schick arm that I used to have, which I had bias problems with, this is properly adjustable. Its a ridiculous bargain for the £500 or so hes charging for it. This 301 has a very special tonearm. It was made by Alfred Bokrand from an Ortofon AS-212 on which he has placed a 12? wand. The workmanship is first class and it tracks like a dream. This model of Ortofon arm is known for its pivot set up- it has wonderful bearings, it has a two part counter weight that will allow for a SPU with built in transformer......============================================================== Dear Alfred. I finally set up the tonearm and I am more than satisfied with the results. It has been a huge improvement in my musical experience. The tonearm is piece of beauty and perfect enginered for music reproduction. The classical records sound heavenly good and Jazz albums never as intimate. The severe wrapped records do never miss the track. The bass response is clean and solid. Great. Thanks for your patience with my issues and I am very grateful for send me another cable. Happy new year Afectuosamente Ignacio Enviado desde mi iPhone (email from 28.12.2016)Hi Alfred Just letting you know that the tonearm arrived safe and sound.I have installed it on a 16 broadcast turntable and it sounds great (and looks good as well). Thank you very much. Wolfgang (email from 30.12.2016) Hello Alfred, I have been wanting to tell you that I have been enjoying your tonearm so very much ! The set up was easy, thank you for the template and alignment tool, it is very precise. The quality of the tonearm is excellent, of course, and I have already found the split counterweight very useful. I have been trying the arm with a Denon 103 and an Ikeda 9C cartridge, and both sound wonderful. The Ikeda requires much more attention to alignments, and your tonearm makes that very simple. It is also nice to have the anti skate adjustment too, which helps a lot with the ikeda. More than anything, Im enjoying music, which is more important than any technicalities. I will send you photos soon of my turntable setup so you may see everything in its happy state. My turntable is a Garrard 401. With many thanks again, in gratitude for your fine work and dedication, S.M New York 17.Sept. 2014 Hallo Alfred, es ist vollbracht. In ca. 3 Tagen habe ich die Zarge für den Neuen aufgebaut.Die ersten Platten drehen sich seit gestern auf dem Ortofon-Bokrand Sp-15.Schon erstaunlich was da aus meinen Eckhörnern kommt.Ich kann ihn nur mit meinem EMT 948 vergleichen mit dem ich seit ca. 1 Jahr sehr intensiv höre.Ich hab das Gefühl, dass das Gespann des Neuen sehr nahe an Perfektion ist und das für ca. 1/3 des Preises des 948!Vielen Dank für deine tolle Arbeit an dem Tonarm! Thomas K.(Germany) 28.12.2012 ORTOFON 12 long with TECHNICS SP-15 from Thomas K. Hi Alfred. I have been using this tone arm with my Garrard 301 / mono Ortofon Spu cartridge. It sounds absolutely superb. I must congratulate you on your fine work. Have you had a chance to post the Ortofon Head shell yet? I am looking forward to using this with my Shure V15mxr cartridge. Many thanks. John ----- Original Message -----Sent: Tuesday, August 14, 2012 6:23 PM Subject: AW: Re: Ortofon Tone Arm Dear Alfred I have finally set up the tonearm and listened to LPs with it. I have to say that it is better than some of my other arms, possibly because of the strong arm tube.(FROM FSK HONG KONG)Hi Alfred, Glad to tell you that I have received and installed the tonearm after some hard work. Sound is great ! Still take some time for the cartridge to break-in but the tracking ability is extraordinary which allows any music to sing beautifully. Otherwise, it seems perfect to me. Thank you for your help ! Hi Alfred, The system actually sounds better and better from day to day. Impressive particular for old LPs. While writing to you, I am listening to the original Moon River of Andy William. The Exdous Song has never sound so good before - Superb !(Original text email from Japan)Dear Alfred I have at last set up your arm and can now give you an early impression of the sound. Beautifully balanced throughout the frequency range, no irritating frequencies stand out. Air and focus are superb. It is very musical with excellent pitch. Tonal range is very even handed and smooth. However the overall feeling is best summed up by saying that it sounds right in particular piano takes on the feel of one you have grown to recognise from your days in school plays.(Original text of the email from UK)---------------------------------------------------------------------Hello Alfred, I received the new cable yesterday afternoon.Thank you very much for your fast and kindly support.At last, I was able to listen to the sound of your special tonearm. WOW ! Excellent !! I love it.I always use DENON DL103-LC2(?? as a standard cartridgetesting the change of the sound. It was still the result of the short time test, but I felt the sound wassplendid.Lower background-noise, wide and deep sound-stage, particularlythe sonority is very natural and clear.(original mail from Mr.T. Japan)_______________________________________________________ Good morning Alfred, Well, yesterday I mounted your arm on the plinth with the SPU Meister Silver. Mounting was a breeze using my tool for determining the spindle to pivot distance. Using the dual counterweight it is also very easy to tune for optimal stylus pressure, at least far more easy than when using one counterweight. So that is a practical plus for the dual counterweights above the ability for mounting less heavy cartridges as well.I asked you before how your tonearm would compare to the Schick and you were modest. No need to! It is so much better than the Schick when using the heavy SPU.. really, it performs better on from low up to the high frequencies. I have been listening, or actually rediscovering, lots of records sinds yesterday afternoon. I always found that the SPU had at some records a bit of harsh highs but these are completely gone now. So that must have been the combination with the Schick, is my guess. Resonances are way better suppressed now and I do believe that the heavy and sturdy construction does not allow for any other movement of the cartridge/needle than lateral movement.I bow deep for your expertise as that must be the basis of the reconstructed Ortofon! We are really impressed here! My suggestion is that I buy two more arms from you. So I keep the one that is on my turntable now and you send over two complete tonearms. These two consist of the one that you customised for me and another one.I want to replace the Schick with a second AB309 and the third will be for a friend who started dancing in my room when he heard your tonearm..So all together:1. I will keep the tonearm I currently have. This one will go to my friend as he likes the J-shaped armtube.2. The customised arm by you, complete with mounting stuff and counterweights, will replace the one that will go to my friend.3. The third tonearm will replace the Schick tonearm on my plinth. So that is a whole new arm.DHT Rob Netherland 02/12/2018 pictures received from satisfied customers IF YOU ARE NOT SATISFIED,MONEY BACK GUARANTEE***************************************

**************************************************here is one of the last feedbacks from july 30thAligned. It is in an aftermarket VTA tower made for the Groovmaster IIti that was on the table before your arm. I will not going back to the GM!!! Only my $11,000 Glanz MH124 is superior and not by $10,000! I am thrilled at this arms performance richness of tone is its major strong point. Bass is tight super extendedand the too end extended and sweet. No ringing or tonal artifacts with this arm.Vocals are on par with the best of the best. Rich defined and harmonically perfect. Thank you sir. Well done! Robin Wyatt Miyajima Labs USA importer.********************************************************************************** Broadcast Tonearm Ortofon AS -309 12 long for Ortofon SPU-G and SME typeHeadshells MADE BY ALFRED BOKRANDGERMAN BROADCAST ENGINEER(RADIO+TV) TONEARM GEOMETRY:EFFEKTIVE LENGTH : 321.459 mm MOUNTING DISTANCE: 309.4mmOVERHANG: 12.65 mmOFFSET ANGLE (DEGREES): 16.89 º continuous wiring included from the Headshell to the RCA´s with silver plated copper litz from USA This tonearm does not have a fixed effective mass, but is variable due to its different counter weights and the distance to the pivot point of the tonearm It is one of the very rare tonearms with variable mass worlwide.A tonearm with variable effective mass, which makes it possible to use all cartridges with low compliance or with high compliance.************************************************ connector fits Ortofon SPU-G and SME type Headshells Improved base maximum stability and less resonance all my Ortofon Tonearms have the same bearingshighest industry standard and sealed maintenance free ***************************** here YouTube video from a satisfied customerGarrard 301 with my Ortofon AS-309 12 long Tonearm https://www.youtube.com/watch?v=cHzdUsc9Zm4&list=PLZIpztUGDMFS2-0dzexJp-sEkUTes5Zdr ********************************************RCA´s REAN brand from NEUTRIK,the worlds leading supplier of professional audio and video connectors – Neutrik AG *********************************** PHYSICS and GEOMETRY never lies.....THIS ARMWAND IS OPTIMIZED FORLOWEST TRACKING DISTORSION3 THINGS DETERMINE THE QUALITY AND THE PERFORMANCE OF A PERFECT TONEARM:1) EFFEKTIVE LENGHT 2) OVERHANG3) OFFSET ANGLE============================ TONEARM GEOMETRY:EFFEKTIVE LENGTH : 321.459 mm MOUNTING DISTANCE: 309.4mmOVERHANG: 12.65 mmOFFSET ANGLE (DEGREES): 16.89 º_____________________________________________________________========================== ORTOFON 12 AS-309 TONEARM HAVE LESS DISTORSIONS AS THE RMG-309 ORTOFON AS-309 12 long compared to ORTOFON RMG-309 SPECIFICATIONS AS-309 RMG-309 pivot to spindle (mm) 308.81 309 effective length (mm) 321.46 320 overhang (mm) 12.65 11 offset angle ° 16.9 15.9 maximum error ° 1.28 1.69 maximum distortion % 0.44 0.58 average rms distortion % 0.29 0.35 all results taken fromvinylengineTonearm Alignment Calculator Pro Tonearm geometry with the lowest distortion worldwide, you will hear it immediately the geometry had to be calculated by hand in the 60s, because you did not have any computer calculation programs yet, this could never be the optimum, because the 3 parameters for the geometry are interdependent. When you change only one parameter to 0.5mm the distortions are great. Therefore, tonearms from the 60s can NEVER reach the perfection that is possible with the computer programs today___________________________________This tonearm combines the simple aesthetics of Ortofon Tonearms with the current best armtube geometry currently available only a perfect geometry of the armtube guarantees a low distortion.this is the first and most important thing with a tonearm.not the material, not exotic armtube materials or mimics can eliminate a fundamental distortion that exist due to a wrong and bad geometry.material of the armtube and Vaccination only has an impact on resonance and vibration coming from the plinth (engine vibration and music waves) tonal arms are offered on the market, which cost well over $ 15,000 and are advertised that give the materials the highest in technology (space travel, NASA ect) the geometry of a perfect tonearm with the lowest distorsions consists of: 1) effective length2) overhang3) offset angle nothing more and nothing less these 3 parameters are dependent on each other. This is mathematics and is based on formulas that have absolutely nothing to do with materials. With existing PC calculation programs, anyone can see if their tonearm has the least distortion due to the armtube geometry. This is the only objective method and not the subjective belief in exotic materials or great promises. if the distortions are very high, because the geometry of the armtube is bad, then helps no ball bearings from NASA or whatever. Many manufacturers want to persuade one. it also no helps no arm tube, made of 500 years old wood, which is the specially manufactured and polished by moonlight from a virgin.**************************************************************** The Armwand is high damped with inlet of Balsa Wood(the inlet of balsa for damping is precisely balanced- when you overdamped you will take the life out of the sound and it will get boring)********************************************************************* Armwand with matt surface and inlet of balsa woodwhich guarantees no resonances in Armtube and CartridgeYOU WILL HEAR THIS.********************************************************************************** continuous internal wiring from the headshell plug to the RCAloom steel braid and PET braid to ensure enhanced signal flow and screening due to the use of a Faraday cage to kill off RF. this is the best what do you can do you not need a expensive tonearm cable buy *********************************************************the benefit of continuous internal wiring from the headshell plug to the RCA *************************************************************** my cable have only 57 pF at 1.2 m in length; the Genesis cable have 135 pF at 1.2 m in length and cost $ 549 high capacities affect and eliminate high and mid frequencies and ruin the original music information ************************************** 2 DIFFERENT COUNTER WEIGHTS2 WEIGHTS TOGETHER FOR ORTOFON SPU-G CARTRIDGS UP TO 35 GRAMSor BIG COUNTER WEIGHT SINGLY FOR CARTRIDGES UP TO 20 GRAMS With this construction you have an enormous range of applications for all Cartridges**************************************** **************************************** TONEARM COMES WITH :MOUNTING TEMPLATEMANUAL SCREWS AND WASHERS FOR MOUNTING COLLARALLEN KEY FOR ADJUST LIFT DEVICE _____________________________ WORLDWIDE SHIPPINGTRACKING AND REGISTERED POST------------------------------------------- reviews from customers( Original text e-mails) from HiFi Wigwam:The Ortofon arm is one of the ones off ebay done by a German guy in Spain (Alfred Bokrand), based on the old (Danish-made) Ortofon AS212/309 bearing housing and anti-skate mechanism, with an arm tube and weights of his own design. I think its a wonderful bit of kit, I prefer it to the Thomas Schick arm that I used to have, which I had bias problems with, this is properly adjustable. Its a ridiculous bargain for the £500 or so hes charging for it. This 301 has a very special tonearm. It was made by Alfred Bokrand from an Ortofon AS-212 on which he has placed a 12? wand. The workmanship is first class and it tracks like a dream. This model of Ortofon arm is known for its pivot set up- it has wonderful bearings, it has a two part counter weight that will allow for a SPU with built in transformer......============================================================== Dear Alfred. I finally set up the tonearm and I am more than satisfied with the results. It has been a huge improvement in my musical experience. The tonearm is piece of beauty and perfect enginered for music reproduction. The classical records sound heavenly good and Jazz albums never as intimate. The severe wrapped records do never miss the track. The bass response is clean and solid. Great. Thanks for your patience with my issues and I am very grateful for send me another cable. Happy new year Afectuosamente Ignacio Enviado desde mi iPhone (email from 28.12.2016)Hi Alfred Just letting you know that the tonearm arrived safe and sound.I have installed it on a 16 broadcast turntable and it sounds great (and looks good as well). Thank you very much.

ortofon AS-309S Static Balance Type 12? Long Tonearm Pickup Arm Audio Equipment Domo Arigato! Welcome, Thank you for your visit. Description Operation confirmed with the following contents. Output from both channels. Lifter descent speed. Each adjustment point, operation feeling. Height adjustment, etc. The appearance is a beautiful product without any noticeable scratches. Specifications Effective length: 311mm (with SPU: 315mm)?Overhang: 15mm?Stylus adjustment range: 0 to 3g?Compatible weight: 18 to 28g (including shell)?Weight: 545g Accessories Standard weightsArm BasePHONO cableFixing screws x 3Fixing wood screws x 3Hexagonal wrench x 2Guide pinMounting templateArm base mounting templateInstruction Manual (Japanese)Original box Shipping Shipping is only available to the address registered in eBay. Shipping is by FedEx or EMS. Free Shipping Returns Unconditional Return Policy Customer service and satisfaction are very important to us.I have an unconditional return policy if notified within 30 of the receipt of the item. All returned items must be the original condition.All return requests must be made within 30 days of the receipt of the item. Please contact me first for return before you ship it back to me.The postage of the returned goods is a buyer burden. International Buyers Please Note:Import duties, taxes and charges are not included in the item price or shipping charges.These charges are the buyer’s responsibility.Please check with your country’s customs office to determine what these additional costs will be prior to bidding/buying.These charges are normally collected by the delivering freight (shipping) company or when you pick the item up -do not confuse them for additional shipping charges.We do not mark merchandise values below value or mark items as “gifts” -US and International government regulations prohibit such behavior. I am sorry but we can not arrange that because it is illegal in Japan.Thank you.

International bidders welcome. ENGLISH BELOW Original Ortofon RMA309 (nicht der spätere i) Inkl. OVP, Zubehör, Armrest und original Tonarmkabel. Der Tonarm ist ca. 50 Jahre alt. Lager revidiert und eingestellt bei Tonmechanik Berlin in 2023. Sehr guter Zustand mit nur geringen Gebrauchspuren. Perfekt zum Betreiben eines SPU A oder SL15-A. Auf Wunsch kann ich ein originales SL15-A anbieten. Das System, Laufwerk und Armbasis sind nicht Teil des Angebots. Versand möglich und inklusive. Oder Abholung vor Ort. Privatverkauf; ich schließe jede Sachmangelhaftung aus. ENGLISH For sale is an original Ortofon RMA309 (not the i version). It is in very nice condition with only minor signs of use. The bearings have been checked and revised at German specialist Tonmechanik Berlin in 2023. The arm comes with original packaging, arm rest and tonearm cable. Everything else you see on pictures is not part of the sale. Private sale. No liability on defects or shipping loss. I can send securely packed with DHL tracked and insured on buyers risk.

Condition DescriptionThe arm is in a beautiful state with no noticeable scratches and gloss. Accessories such as weights and cables are also good. The shell is also slightly scratched and no major damage is found. Considering the aging, we judge it as a beautiful item. It will be a used item that has been used for many years. Please note that there are scratches / dullness / feeling of use due to aging / use. ? Operation We have confirmed the operation with our equipment. ? Output from both channels ? Each adjustment point, operation feeling ? Height adjustment, etc. There is no problem in operation. ? Accessories ? G shell (ortofon) ·weight ? Arm base ? Wood screws x 3 ? Armrest ? Rest mounting nut / washer ? PHONO cable (ortofon 8N-TSW1000) ? Instruction manual (copy) ? Mounting template (copy) ? Product details Manufacturer: orotofon Model: RMG-309i Overall length: 408 mm (when G shell is attached) Execution length: 320 mm ± 1.5 mm Overhang: 11mm Stylus pressure range: 0-7g Please Note shipping from Japan. Policy PaymentWe can shipping only registered address on ebay. Import duties, taxes and charges are not included in the item price or shipping charges. These charges are the buyers responsibility.ShippingI send a product by EMS(Japan Post) or International Priority(FedEx). I will determine the required shipping company depending on the situation. I attach the tracking number. Please bid it without worrying. Shipping is only available to the address registered in Paypal. Please note that any address not registered in Paypal is not acceptable to ship. Shipping is available from Monday to Friday. Weekends are not available because post office is closed.Terms of SaleImport duties, taxes and charges are not included in the item price or shipping charges. These charges are the buyers responsibility. Please check with your countrys customs office to determine what these additional costs will be prior to Unconditional Return Policy Customer service and satisfaction are very important to us. I have an unconditional return policy if notified within 30 of the receipt of the item. All returned items must be the original condition. All return requests must be made within 30 days of the receipt of the item. Please contact me first for return before you ship it back to me.International BuyersImport duties, taxes and charges are not included in the item price or shipping charges. These charges are the buyers responsibility. Please check with your countrys customs office to determine what these additional costs will be prior to bidding/buying. These charges are normally collected by the delivering freight (shipping) company or when you pick the item up - do not confuse them for additional shipping charges.

Condition DescriptionThere are no noticeable scratches on the arm and it is glossy / glossy and beautiful. There are no dents or bends in the pipe, and there is no damage to the weight shaft. Considering the aging, we judge it as a beautiful item. ? Operation We have confirmed the operation with our equipment. ? Output from both channels ? Each adjustment point, operation feeling ? Height adjustment, etc. There is no problem in operation. ? Accessories ? Arm stand ? Stand fixing screw x 3 ? Armrest ? Rest mounting nut / washer ? PHONO cable ? Marking pin holder ? Instruction manual (copy for RMG-309i, but as a bonus) ? Mounting template (copy) ? Product details Manufacturer: ortofon Model: RMG309 Overall length: 406mm Execution length: 320 mm Overhang: 11mm Stylus pressure range: 0-7g Please Note shipping from Japan. Policy PaymentWe can shipping only registered address on ebay. Import duties, taxes and charges are not included in the item price or shipping charges. These charges are the buyers responsibility.ShippingI send a product by EMS(Japan Post) or International Priority(FedEx). I will determine the required shipping company depending on the situation. I attach the tracking number. Please bid it without worrying. Shipping is only available to the address registered in Paypal. Please note that any address not registered in Paypal is not acceptable to ship. Shipping is available from Monday to Friday. Weekends are not available because post office is closed.Terms of SaleImport duties, taxes and charges are not included in the item price or shipping charges. These charges are the buyers responsibility. Please check with your countrys customs office to determine what these additional costs will be prior to Unconditional Return Policy Customer service and satisfaction are very important to us. I have an unconditional return policy if notified within 30 of the receipt of the item. All returned items must be the original condition. All return requests must be made within 30 days of the receipt of the item. Please contact me first for return before you ship it back to me.International BuyersImport duties, taxes and charges are not included in the item price or shipping charges. These charges are the buyers responsibility. Please check with your countrys customs office to determine what these additional costs will be prior to bidding/buying. These charges are normally collected by the delivering freight (shipping) company or when you pick the item up - do not confuse them for additional shipping charges.

Condition DescriptionWorks perfectly, good product. There is no noticeable damage on the whole, and it is in good condition with gloss/gloss. There are no dents or bends in the pipe, nor damage to the weight shaft. Considering the age, we will judge it as a good product. ? Operation? We have confirmed the operation of our equipment. ?Output from both channels ? Each adjustment point, operation feeling ?Height adjustment, etc. There is no problem in operation. ?Accessories ?Arm stand ?Stand fixing screw x 3 ?Armrest ?Mounting nut/washer for rest ?PHONO cable ?Instruction manual (copy English) ?Mounting template (copy) ? commodity contents Manufacturer: ortofon Model number: RMG309 Total length: 406mm Running Length: 320mm Overhang: 11mm Stylus pressure range: 0-7g Please Note shipping from Japan. Policy PaymentWe can shipping only registered address on ebay. Import duties, taxes and charges are not included in the item price or shipping charges. These charges are the buyers responsibility.ShippingI send a product by EMS(Japan Post) or International Priority(FedEx). I will determine the required shipping company depending on the situation. I attach the tracking number. Please bid it without worrying. Shipping is only available to the address registered in Paypal. Please note that any address not registered in Paypal is not acceptable to ship. Shipping is available from Monday to Friday. Weekends are not available because post office is closed.Terms of SaleImport duties, taxes and charges are not included in the item price or shipping charges. These charges are the buyers responsibility. Please check with your countrys customs office to determine what these additional costs will be prior to Unconditional Return Policy Customer service and satisfaction are very important to us. I have an unconditional return policy if notified within 30 of the receipt of the item. All returned items must be the original condition. All return requests must be made within 30 days of the receipt of the item. Please contact me first for return before you ship it back to me.International BuyersImport duties, taxes and charges are not included in the item price or shipping charges. These charges are the buyers responsibility. Please check with your countrys customs office to determine what these additional costs will be prior to bidding/buying. These charges are normally collected by the delivering freight (shipping) company or when you pick the item up - do not confuse them for additional shipping charges.

**************************************************here is one of the last feedbacks from july 30thAligned. It is in an aftermarket VTA tower made for the Groovmaster IIti that was on the table before your arm. I will not going back to the GM!!! Only my $11,000 Glanz MH124 is superior and not by $10,000! I am thrilled at this arms performance richness of tone is its major strong point. Bass is tight super extendedand the too end extended and sweet. No ringing or tonal artifacts with this arm.Vocals are on par with the best of the best. Rich defined and harmonically perfect. Thank you sir. Well done! Robin Wyatt Miyajima Labs USA importer.********************************************************************************** Broadcast Tonearm Ortofon AS -309 12 long for Ortofon SPU-G and SME typeHeadshells MADE BY ALFRED BOKRANDGERMAN BROADCAST ENGINEER(RADIO+TV) TONEARM GEOMETRY:EFFEKTIVE LENGTH : 321.459 mm MOUNTING DISTANCE: 309.4mmOVERHANG: 12.65 mmOFFSET ANGLE (DEGREES): 16.89 º continuous wiring included from the Headshell to the RCA´s with silver plated copper litz from USA This tonearm does not have a fixed effective mass, but is variable due to its different counter weights and the distance to the pivot point of the tonearm It is one of the very rare tonearms with variable mass worlwide.A tonearm with variable effective mass, which makes it possible to use all cartridges with low compliance or with high compliance.************************************************ connector fits Ortofon SPU-G and SME type Headshells Improved base maximum stability and less resonance all my Ortofon Tonearms have the same bearingshighest industry standard and sealed maintenance free ***************************** here YouTube video from a satisfied customerGarrard 301 with my Ortofon AS-309 12 long Tonearm https://www.youtube.com/watch?v=cHzdUsc9Zm4&list=PLZIpztUGDMFS2-0dzexJp-sEkUTes5Zdr ********************************************RCA´s REAN brand from NEUTRIK,the worlds leading supplier of professional audio and video connectors – Neutrik AG *********************************** PHYSICS and GEOMETRY never lies.....THIS ARMWAND IS OPTIMIZED FORLOWEST TRACKING DISTORSION3 THINGS DETERMINE THE QUALITY AND THE PERFORMANCE OF A PERFECT TONEARM:1) EFFEKTIVE LENGHT 2) OVERHANG3) OFFSET ANGLE============================ TONEARM GEOMETRY:EFFEKTIVE LENGTH : 321.459 mm MOUNTING DISTANCE: 309.4mmOVERHANG: 12.65 mmOFFSET ANGLE (DEGREES): 16.89 º_____________________________________________________________========================== ORTOFON 12 AS-309 TONEARM HAVE LESS DISTORSIONS AS THE RMG-309 ORTOFON AS-309 12 long compared to ORTOFON RMG-309 SPECIFICATIONS AS-309 RMG-309 pivot to spindle (mm) 308.81 309 effective length (mm) 321.46 320 overhang (mm) 12.65 11 offset angle ° 16.9 15.9 maximum error ° 1.28 1.69 maximum distortion % 0.44 0.58 average rms distortion % 0.29 0.35 all results taken fromvinylengineTonearm Alignment Calculator Pro Tonearm geometry with the lowest distortion worldwide, you will hear it immediately the geometry had to be calculated by hand in the 60s, because you did not have any computer calculation programs yet, this could never be the optimum, because the 3 parameters for the geometry are interdependent. When you change only one parameter to 0.5mm the distortions are great. Therefore, tonearms from the 60s can NEVER reach the perfection that is possible with the computer programs today___________________________________This tonearm combines the simple aesthetics of Ortofon Tonearms with the current best armtube geometry currently available only a perfect geometry of the armtube guarantees a low distortion.this is the first and most important thing with a tonearm.not the material, not exotic armtube materials or mimics can eliminate a fundamental distortion that exist due to a wrong and bad geometry.material of the armtube and Vaccination only has an impact on resonance and vibration coming from the plinth (engine vibration and music waves) tonal arms are offered on the market, which cost well over $ 15,000 and are advertised that give the materials the highest in technology (space travel, NASA ect) the geometry of a perfect tonearm with the lowest distorsions consists of: 1) effective length2) overhang3) offset angle nothing more and nothing less these 3 parameters are dependent on each other. This is mathematics and is based on formulas that have absolutely nothing to do with materials. With existing PC calculation programs, anyone can see if their tonearm has the least distortion due to the armtube geometry. This is the only objective method and not the subjective belief in exotic materials or great promises. if the distortions are very high, because the geometry of the armtube is bad, then helps no ball bearings from NASA or whatever. Many manufacturers want to persuade one. it also no helps no arm tube, made of 500 years old wood, which is the specially manufactured and polished by moonlight from a virgin.**************************************************************** The Armwand is high damped with inlet of Balsa Wood(the inlet of balsa for damping is precisely balanced- when you overdamped you will take the life out of the sound and it will get boring)********************************************************************* Armwand with matt surface and inlet of balsa woodwhich guarantees no resonances in Armtube and CartridgeYOU WILL HEAR THIS.********************************************************************************** continuous internal wiring from the headshell plug to the RCAloom steel braid and PET braid to ensure enhanced signal flow and screening due to the use of a Faraday cage to kill off RF. this is the best what do you can do you not need a expensive tonearm cable buy *********************************************************the benefit of continuous internal wiring from the headshell plug to the RCA *************************************************************** my cable have only 57 pF at 1.2 m in length; the Genesis cable have 135 pF at 1.2 m in length and cost $ 549 high capacities affect and eliminate high and mid frequencies and ruin the original music information ************************************** 2 DIFFERENT COUNTER WEIGHTS2 WEIGHTS TOGETHER FOR ORTOFON SPU-G CARTRIDGS UP TO 35 GRAMSor BIG COUNTER WEIGHT SINGLY FOR CARTRIDGES UP TO 20 GRAMS With this construction you have an enormous range of applications for all Cartridges**************************************** **************************************** TONEARM COMES WITH :MOUNTING TEMPLATEMANUAL SCREWS AND WASHERS FOR MOUNTING COLLARALLEN KEY FOR ADJUST LIFT DEVICE _____________________________ WORLDWIDE SHIPPINGTRACKING AND REGISTERED POST------------------------------------------- reviews from customers( Original text e-mails) from HiFi Wigwam:The Ortofon arm is one of the ones off ebay done by a German guy in Spain (Alfred Bokrand), based on the old (Danish-made) Ortofon AS212/309 bearing housing and anti-skate mechanism, with an arm tube and weights of his own design. I think its a wonderful bit of kit, I prefer it to the Thomas Schick arm that I used to have, which I had bias problems with, this is properly adjustable. Its a ridiculous bargain for the £500 or so hes charging for it. This 301 has a very special tonearm. It was made by Alfred Bokrand from an Ortofon AS-212 on which he has placed a 12? wand. The workmanship is first class and it tracks like a dream. This model of Ortofon arm is known for its pivot set up- it has wonderful bearings, it has a two part counter weight that will allow for a SPU with built in transformer......============================================================== Dear Alfred. I finally set up the tonearm and I am more than satisfied with the results. It has been a huge improvement in my musical experience. The tonearm is piece of beauty and perfect enginered for music reproduction. The classical records sound heavenly good and Jazz albums never as intimate. The severe wrapped records do never miss the track. The bass response is clean and solid. Great. Thanks for your patience with my issues and I am very grateful for send me another cable. Happy new year Afectuosamente Ignacio Enviado desde mi iPhone (email from 28.12.2016)Hi Alfred Just letting you know that the tonearm arrived safe and sound.I have installed it on a 16 broadcast turntable and it sounds great (and looks good as well). Thank you very much.

ortofon RMA309i Improved Dynamic Balance Type Tonearm Pickup Arm for SPU A Shell Domo Arigato! Welcome, Thank you for your visit. Description Unused item. Only unpacked for photographing. This is an improved model by ortofon Japan. Specifications Dynamic Balanced Tone ArmOverall length (from the tip of the head shell to the end of the weight) : approx. 408mmEffective length (center of axis of revolution - tip of Stylus) : 320mmEffective length (center of axis of revolution - center of turntable) : 309mmOffset angle : 16Overhang : 11mmStylus pressure adjustment range (direct reading) : 0-7gEffective movement range : 2-7gHeight adjustment range : 35-63mmCenter hole diameter for arm base installation : 21-22mm dia.Arm rest mounting hole diameter: 10.5-11mm dia.Compatible cartridge weight: 30-33g (including shell) *Output cable 6NX-TSW1010 is included Shipping Shipping is only available to the address registered in eBay. Shipping is by FedEx or EMS. Free Shipping Returns Unconditional Return Policy Customer service and satisfaction are very important to us.I have an unconditional return policy if notified within 30 of the receipt of the item. All returned items must be the original condition.All return requests must be made within 30 days of the receipt of the item. Please contact me first for return before you ship it back to me.The postage of the returned goods is a buyer burden. International Buyers Please Note:Import duties, taxes and charges are not included in the item price or shipping charges.These charges are the buyer’s responsibility.Please check with your country’s customs office to determine what these additional costs will be prior to bidding/buying.These charges are normally collected by the delivering freight (shipping) company or when you pick the item up -do not confuse them for additional shipping charges.We do not mark merchandise values below value or mark items as “gifts” -US and International government regulations prohibit such behavior. I am sorry but we can not arrange that because it is illegal in Japan.Thank you.

For the audiophiles all over the world ORTOFON products reach legendary status. And thats rightfully. This is a opportunity to own whats becoming rare and more expensive on the world market. Excellent tonearm for serious music lovers ********************Broadcast Tonearm Ortofon AB -309 banana 12 long for Ortofon SPU-G and SME type Headshells ONE OF THE BEST 12 LONG TONEARMSMADE BY ALFRED BOKRANDGERMAN BROADCAST ENGINEER(RADIO+TV) WHY?PHYSICS and GEOMETRY never lies.....THIS ARMWAND IS OPTIMIZED FORLOWEST TRACKING DISTORSION3 THINGS DETERMINE THE QUALITY AND THE PERFORMANCE OF A PERFECT TONEARM:1) EFFEKTIVE LENGHT 2) OVERHANG3) OFFSET ANGLE============================ TONEARM GEOMETRY:EFFEKTIVE LENGTH : 321.459 mm MOUNTING DISTANCE: 309.4mmOVERHANG: 12.66 mmOFFSET ANGLE (DEGREES): 16.9 º _____________________________________________________________========================== ORTOFON 12 AS-309 TONEARM HAVE LESS DISTORSIONS AS THE SME 3012 series I ORTOFON AS-309 12 long compared to SME 3012 series I 309.4 mm mounting distance 294 mm 321.5 mm effektive lenght 305 mm 12.6 mm Over hang 11 mm 16.9 º offset angle(degrees) 16.15 º 1.26 º maximum error º 2.11 º 0.3 % average distorsion 0.36 % 0.46 % maximum distorsion 0.72 % all results taken fromAlignment Calculator Provinylengine page Tonearm geometry with the lowest distortion worldwide, you will hear it immediately the geometry had to be calculated by hand in the 60s, because you did not have any computer calculation programs yet, this could never be the optimum, because the 3 parameters for the geometry are interdependent. When you change only one parameter to 0.5mm the distortions are great. Therefore, tonearms from the 60s can NEVER reach the perfection that is possible with the computer programs today___________________________________This tonearm combines the simple aesthetics of Ortofon Tonearms with the current best armtube geometry currently available only a perfect geometry of the armtube guarantees a low distortion.this is the first and most important thing with a tonearm.not the material, not exotic armtube materials or mimics can eliminate a fundamental distortion that exist due to a wrong and bad geometry.material of the armtube and Vaccination only has an impact on resonance and vibration coming from the plinth (engine vibration and music waves) tonal arms are offered on the market, which cost well over $ 15,000 and are advertised that give the materials the highest in technology (space travel, NASA ect) the geometry of a perfect tonearm with the lowest distorsions consists of: 1) effective length2) overhang3) offset angle nothing more and nothing less these 3 parameters are dependent on each other. This is mathematics and is based on formulas that have absolutely nothing to do with materials. With existing PC calculation programs, anyone can see if their tonearm has the least distortion due to the armtube geometry. This is the only objective method and not the subjective belief in exotic materials or great promises..**************************************************************** positive feedbacks Aligned. It is in an aftermarket VTA tower made for the Groovmaster IIti that was on the table before your arm. I will not going back to the GM!!! Only my $11,000 Glanz MH124 is superior and not by $10,000! I am thrilled at this arms performance richness of tone is its major strong point. Bass is tight super extended and the too end extended and sweet. No ringing or tonal artifacts with this arm. Vocals are on par with the best of the best. Rich defined and harmonical. Thank you sir. Well done! Robin WyattMiyajima Labs USA importer. _______________________________ My Ortofon tonearms go over the SME 3012 and SME 3012R, which costs about 5000 euros. It is only surpassed by a GLANZ for $11,000. Thats not what Im saying, but my customers.see here original mailsDear mr. BokrandI gave myself some time to make sure I wasn’t too hasty in judging. After many hours of listening to my favorite records, which I know very well, I can say that your arm holds up very well the comparison with my beloved SME 3012R, indeed, with the Ortofon SPU is superior in clarity, dynamics (!!!), soundness of bass...Thanks for everythingMassimo Longoni________________________________________________________________________ screw for setting Azimuth 2 DIFFERENT COUNTER WEIGHTS 2 WEIGHTS TOGETHER FOR ORTOFON SPU-G CARTRIDGS UP TO 35 GRAMS or BIG COUNTER WEIGHT SINGLY FOR CARTRIDGES UP TO 20 GRAMS With this construction you have an enormous range of applications for all Cartridges _________________________________________________ liftlever is modified by me in the vintage Ortofon style like the Ortofon Hi Jack.I like this classic timeless style ******************************** TONEARM COMES WITH :MOUNTING TEMPLATEMANUALSCREWS AND WASHERS FOR MOUNTING COLLARALLEN KEY FOR ADJUST LIFT DEVICESCREW DRIVER FOR WEIGHTSSCREW DRIVER FOR AZIMUTH ADJUST in the manual you will always find an original sample of the internal wiring WORLDWIDE FREE SHIPPINGTRACKING AND REGISTERED POST------------------------------------------- reviews from customers( Original text e-mails) from HiFi Wigwam:The Ortofon arm is one of the ones off ebay done by a German guy in Spain (Alfred Bokrand), based on the old (Danish-made) Ortofon AS212/309 bearing housing and anti-skate mechanism, with an arm tube and weights of his own design. I think its a wonderful bit of kit, I prefer it to the Thomas Schick arm that I used to have, which I had bias problems with, this is properly adjustable. Its a ridiculous bargain for the £500 or so hes charging for it. This 301 has a very special tonearm. It was made by Alfred Bokrand from an Ortofon AS-212 on which he has placed a 12? wand. The workmanship is first class and it tracks like a dream. This model of Ortofon arm is known for its pivot set up- it has wonderful bearings, it has a two part counter weight that will allow for a SPU with built in transformer......============================================================== Dear Alfred. I finally set up the tonearm and I am more than satisfied with the results. It has been a huge improvement in my musical experience. The tonearm is piece of beauty and perfect enginered for music reproduction. The classical records sound heavenly good and Jazz albums never as intimate. The severe wrapped records do never miss the track. The bass response is clean and solid. Great. Thanks for your patience with my issues and I am very grateful for send me another cable. Happy new year Afectuosamente Ignacio Enviado desde mi iPhone (email from 28.12.2016)Hi Alfred Just letting you know that the tonearm arrived safe and sound.I have installed it on a 16 broadcast turntable and it sounds great (and looks good as well). Thank you very much. Wolfgang (email from 30.12.2016) Hello Alfred, I have been wanting to tell you that I have been enjoying your tonearm so very much ! The set up was easy, thank you for the template and alignment tool, it is very precise. The quality of the tonearm is excellent, of course, and I have already found the split counterweight very useful. I have been trying the arm with a Denon 103 and an Ikeda 9C cartridge, and both sound wonderful. The Ikeda requires much more attention to alignments, and your tonearm makes that very simple. It is also nice to have the anti skate adjustment too, which helps a lot with the ikeda. More than anything, Im enjoying music, which is more important than any technicalities. I will send you photos soon of my turntable setup so you may see everything in its happy state. My turntable is a Garrard 401. With many thanks again, in gratitude for your fine work and dedication, S.M New York 17.Sept. 2014 Hallo Alfred, es ist vollbracht. In ca. 3 Tagen habe ich die Zarge für den Neuen aufgebaut.Die ersten Platten drehen sich seit gestern auf dem Ortofon-Bokrand Sp-15.Schon erstaunlich was da aus meinen Eckhörnern kommt.Ich kann ihn nur mit meinem EMT 948 vergleichen mit dem ich seit ca. 1 Jahr sehr intensiv höre.Ich hab das Gefühl, dass das Gespann des Neuen sehr nahe an Perfektion ist und das für ca. 1/3 des Preises des 948!Vielen Dank für deine tolle Arbeit an dem Tonarm! Thomas K.(Germany) 28.12.2012 ORTOFON 12 long with TECHNICS SP-15 from Thomas K. Hi Alfred. I have been using this tone arm with my Garrard 301 / mono Ortofon Spu cartridge. It sounds absolutely superb. I must congratulate you on your fine work. Have you had a chance to post the Ortofon Head shell yet? I am looking forward to using this with my Shure V15mxr cartridge. Many thanks. John ----- Original Message -----Sent: Tuesday, August 14, 2012 6:23 PM Subject: AW: Re: Ortofon Tone Arm Dear Alfred I have finally set up the tonearm and listened to LPs with it. I have to say that it is better than some of my other arms, possibly because of the strong arm tube.(FROM FSK HONG KONG)Hi Alfred, Glad to tell you that I have received and installed the tonearm after some hard work. Sound is great ! Still take some time for the cartridge to break-in but the tracking ability is extraordinary which allows any music to sing beautifully. Otherwise, it seems perfect to me. Thank you for your help ! Hi Alfred, The system actually sounds better and better from day to day. Impressive particular for old LPs. While writing to you, I am listening to the original Moon River of Andy William. The Exdous Song has never sound so good before - Superb !(Original text email from Japan)Dear Alfred I have at last set up your arm and can now give you an early impression of the sound. Beautifully balanced throughout the frequency range, no irritating frequencies stand out. Air and focus are superb. It is very musical with excellent pitch. Tonal range is very even handed and smooth. However the overall feeling is best summed up by saying that it sounds right in particular piano takes on the feel of one you have grown to recognise from your days in school plays.(Original text of the email from UK)---------------------------------------------------------------------Hello Alfred, I received the new cable yesterday afternoon.Thank you very much for your fast and kindly support.At last, I was able to listen to the sound of your special tonearm. WOW ! Excellent !! I love it.I always use DENON DL103-LC2(?? as a standard cartridgetesting the change of the sound. It was still the result of the short time test, but I felt the sound wassplendid.Lower background-noise, wide and deep sound-stage, particularlythe sonority is very natural and clear.(original mail from Mr.T. Japan)_______________________________________________________ Good morning Alfred, Well, yesterday I mounted your arm on the plinth with the SPU Meister Silver. Mounting was a breeze using my tool for determining the spindle to pivot distance. Using the dual counterweight it is also very easy to tune for optimal stylus pressure, at least far more easy than when using one counterweight. So that is a practical plus for the dual counterweights above the ability for mounting less heavy cartridges as well.I asked you before how your tonearm would compare to the Schick and you were modest. No need to! It is so much better than the Schick when using the heavy SPU.. really, it performs better on from low up to the high frequencies. I have been listening, or actually rediscovering, lots of records sinds yesterday afternoon. I always found that the SPU had at some records a bit of harsh highs but these are completely gone now. So that must have been the combination with the Schick, is my guess. Resonances are way better suppressed now and I do believe that the heavy and sturdy construction does not allow for any other movement of the cartridge/needle than lateral movement.I bow deep for your expertise as that must be the basis of the reconstructed Ortofon! We are really impressed here! My suggestion is that I buy two more arms from you. So I keep the one that is on my turntable now and you send over two complete tonearms. These two consist of the one that you customised for me and another one.I want to replace the Schick with a second AB309 and the third will be for a friend who started dancing in my room when he heard your tonearm..So all together:1. I will keep the tonearm I currently have. This one will go to my friend as he likes the J-shaped armtube.2. The customised arm by you, complete with mounting stuff and counterweights, will replace the one that will go to my friend.3. The third tonearm will replace the Schick tonearm on my plinth. So that is a whole new arm.DHT Rob Netherland 02/12/2018 pictures received from satisfied customers IF YOU ARE NOT SATISFIED,MONEY BACK GUARANTEE***************************************

70s year Ortofon RMA-309 tonearm for EMT cartridge, with armrest, cable VG++ Armward of this tonearm is longer than RMG-309, it was made for using with EMT type headshell, the connector is not square, it is EMT type. Perfect working condition. Please check business term before bidding on my item /////////////////////////////// NOTE: 1. If you want to buy item, press buy it now or make offer button if you want to offer your best price. 2. I only ship item via EMS or Fedex, I dont accept ship item via sea way. 3. Please make your payment within 3 days. 4. If you have any question about item, feel free to ask me before bidding. Generally, I dont response to question ask about what is your best price, you can press best offer button and input your best price. If there is no best offer button then item is fixed price. 5. If you want to find any item related to audio turntable, audio vintage or amplifier, and you can not see in my listing, please ask me via message, I can help you find it. 6. If you want to know about me, you can search on google with key word Otomon Laboratory //////////////////////////////

Condition DescriptionWorks perfectly, good product. There is no noticeable damage on the whole, and it is in good condition with gloss/gloss. There are no dents or bends in the pipe, nor damage to the weight shaft. Considering the age, we will judge it as a good product. ? Operation? We have confirmed the operation of our equipment. ?Output from both channels ? Each adjustment point, operation feeling ?Height adjustment, etc. There is no problem in operation. ?Accessories ?Arm stand ?Stand fixing screw x 3 ?Armrest ?Mounting nut/washer for rest ?PHONO cable ?Instruction manual (copy English) ?Mounting template (copy) ? commodity contents Manufacturer: ortofon Model number: RMG309 Total length: 406mm Running Length: 320mm Overhang: 11mm Stylus pressure range: 0-7g Please Note shipping from Japan. Policy PaymentWe can shipping only registered address on ebay. Import duties, taxes and charges are not included in the item price or shipping charges. These charges are the buyers responsibility.ShippingI send a product by EMS(Japan Post) or International Priority(FedEx). I will determine the required shipping company depending on the situation. I attach the tracking number. Please bid it without worrying. Shipping is only available to the address registered in Paypal. Please note that any address not registered in Paypal is not acceptable to ship. Shipping is available from Monday to Friday. Weekends are not available because post office is closed.Terms of SaleImport duties, taxes and charges are not included in the item price or shipping charges. These charges are the buyers responsibility. Please check with your countrys customs office to determine what these additional costs will be prior to Unconditional Return Policy Customer service and satisfaction are very important to us. I have an unconditional return policy if notified within 30 of the receipt of the item. All returned items must be the original condition. All return requests must be made within 30 days of the receipt of the item. Please contact me first for return before you ship it back to me.International BuyersImport duties, taxes and charges are not included in the item price or shipping charges. These charges are the buyers responsibility. Please check with your countrys customs office to determine what these additional costs will be prior to bidding/buying. These charges are normally collected by the delivering freight (shipping) company or when you pick the item up - do not confuse them for additional shipping charges.

Condition DescriptionThere are no noticeable scratches on the arm and it is glossy / glossy and beautiful. There are no dents or bends in the pipe, and there is no damage to the weight shaft. Considering the aging, we judge it as a beautiful item. ? Operation We have confirmed the operation with our equipment. ? Output from both channels ? Each adjustment point, operation feeling ? Height adjustment, etc. There is no problem in operation. ? Accessories ? Arm stand ? Stand fixing screw x 3 ? Armrest ? Rest mounting nut / washer ? PHONO cable ? Marking pin holder ? Instruction manual (copy for RMG-309i, but as a bonus) ? Mounting template (copy) ? Product details Manufacturer: ortofon Model: RMG309 Overall length: 406mm Execution length: 320 mm Overhang: 11mm Stylus pressure range: 0-7g Please Note shipping from Japan. Policy PaymentWe can shipping only registered address on ebay. Import duties, taxes and charges are not included in the item price or shipping charges. These charges are the buyers responsibility.ShippingI send a product by EMS(Japan Post) or International Priority(FedEx). I will determine the required shipping company depending on the situation. I attach the tracking number. Please bid it without worrying. Shipping is only available to the address registered in Paypal. Please note that any address not registered in Paypal is not acceptable to ship. Shipping is available from Monday to Friday. Weekends are not available because post office is closed.Terms of SaleImport duties, taxes and charges are not included in the item price or shipping charges. These charges are the buyers responsibility. Please check with your countrys customs office to determine what these additional costs will be prior to Unconditional Return Policy Customer service and satisfaction are very important to us. I have an unconditional return policy if notified within 30 of the receipt of the item. All returned items must be the original condition. All return requests must be made within 30 days of the receipt of the item. Please contact me first for return before you ship it back to me.International BuyersImport duties, taxes and charges are not included in the item price or shipping charges. These charges are the buyers responsibility. Please check with your countrys customs office to determine what these additional costs will be prior to bidding/buying. These charges are normally collected by the delivering freight (shipping) company or when you pick the item up - do not confuse them for additional shipping charges.