This pre-main amplifier is completed by carefully refining and combining the three factors of circuit, mechanism and parts.The power stage adopts NM-LAPT (Non Magnetic Liner Amplification Power Transistor) developed as a power transistor exclusively for audio.The NM-LAPT is made of pure copper material all the way up to the bonding wire, and realizes excellent high-frequency characteristics and high current limit value by manufacturing cut-off frequency (fT) and fracture resistance (PC).Since the ground circuit of the power supply circuit is connected to the ground circuit of the amplifier circuit (negative output), we have introduced the original advanced ? -X balance circuit to prevent the reverse current from the speaker side from flowing into the amplifier circuit and the deterioration of sound quality.The amplifier circuit is completely independent from the ground circuit, and is balanced in such a way that transmission and amplification are carried out simultaneously, so that the circuit itself blocks out external noise and in-phase distortion.The dynamic frequency characteristics are also improved by reducing the impedance of the circuit to minimize the influence on the passing signal.In addition, a 4-amp configuration with dedicated amplifiers on the + side and - side each provides a push-pull system that drives from both directions under the same conditions on the + side and - side, thereby obtaining strong sound at a low distortion rate.It further improves the perfection of the diamond actuation circuit in which - output can be taken out without phase inversion.The cascade connection of the first stage FET realizes a wide range and high speed with excellent wide-area characteristics and greatly reduces the effect caused by impedance differences with external devices.We have developed a new power transformer (IDEAL SILENT POWER TRANSFORMER) and a capacitor for power supply, and have succeeded in greatly improving power supply capability and stability.Both primary and secondary transformers use OFC lead wires to minimize magnetic induction (?????????). The transformer weight is 13 kg because the shield is made of four layers of copper short rings, two layers of silicon steel plates and a squeeze case, high-density packing is used, and insulation materials are examined.The electrolytic condenser and fast recovery diode have also been completely changed to the one exclusively for the highest sound quality.All custom-made, low-impedance, clean NEW ? -X balanced power supplies and a closed-loop configuration independent of ground minimize the negative effects of unbalanced power supplies on music signals.The power supply unit is placed in the center and the power units are arranged symmetrically with the introduction of reinforced twin monaural construction. Each part with improved strength prevents sound quality degradation due to vibration, and acquires excellent sound image localization and phase characteristics.In addition to vibration control by twin monaural construction, various components with high internal loss and vibration absorption effect are used abundantly, such as large insulators made of pure copper muku covered with felt, pure copper bases and copper-plated parts.In addition, we have newly adopted the isolation of pure copper material, which has conventionally been used between the transformer and the chassis, between the electrolytic capacitor and the chassis, and between the amplifier base and the bottom plate, etc., between the master volume and the chassis, between the radiator and the power board, and even the transformer, electrolytic capacitor, power board, and power board itself.As for the mounting structure of each part, for example, the case of the transformer is attached to the chassis instead of attaching the main body of the transformer directly to the chassis. We have succeeded in effectively blocking the transmission route of vibration by means of the opposed mechanical feedback.In order to improve sound quality, the quality of each part is also thoroughly pursued.In addition to the development of transformers and condensers, we have adopted rolled copper substrates for power boards and power supply boards, plated copper on rear panels, painted hoods with paint containing copper, and adopted bronze screws.All parts are designed to be non-magnetic, vibration-proof, low impedance and high speed.It is equipped with an input terminal that realizes high-purity transmission and amplification of digital sources by directly inputting audio signals to the power amplifier section.Since there is a balanced input in addition to the normal input, setting by balance transmission and amplification is possible by connecting with an external device with a balanced output.Equipped with a source power direct switch that transmits all line input signals directly to the power amplifier with one touch operation.Connect and amplify directly without passing through any accessory functions to reproduce the pure sound of the source.Equipped with a recording function for effective recording and listening when a CD player is connected to the Power Amp Direct.For example, you can listen to the source input to Normal 1 while back-recording a CD or other source connected to Normal 2.Equipped with all-gold plated input terminal, large speaker terminal, large insulator made of pure copper, real side wood, power cord / AC outlet with polarity display, etc. TypeIntegrated amplifierPower Amplifier UnitRated output (20 Hz to 20 kHzSimultaneous operation on both channels, THD0.003%)6 ? : 190W + 190W8 ? : 160W + 160WTotal harmonic distortion factor0.003% or Less (Rated Output, 20 Hz to 20 kHz, 8 ? Load)Frequency characteristicDC ~ 300 kHz, + 0 -3dB (at 1W Output)Cross modulation distortion factor0.003% or Less (at 8 ? Load)Damping factor150 (8 ?)Input Sensitivity / Impedance1V/5k ? (1 kHz)Signal-to-noise ratio120 dB or more (A network)Dynamic Power6 ? : 310W4 ? : 390W2 ? : 580WTIM (SAWTOOTH)Measurement limit value or lessSlew rate200 V / ? secRise time0.5 ? secInput Sensitivity / Impedance(1kHz)Phono MM : 2.5mV/47k ?Phono MC : 300 ? V/100 ?CD, Tuner, Line, Tape/DAT1 / 2 / 3 : 150mV/20k ?Phono maximum allowable inputMM(THD 0.01%):250mVMC(THD 0.1%):25mVFrequency Response (1W)Phono MM : 20 Hz to 20 kHz, ± 0.2 dBCD, Tuner, Line, Tape/DAT-1 / 2 / 3 : DC ~ 300 Hz, + 0 -3dBSignal-to-noise ratio (A network)Phono MM : 90 dB or morePhono MC : 75 dB or moreCD, Tuner, Line, Tape/DAT-1 / 2 / 3 : 110 dB or moreTone controlMaximum variation of BASS : + / - 5 dB at 50 HzMaximum change of TREBLE : ± 5 dB (15 kHz)Subsonic filter16 Hz (-3dB), 6dB/oct.Loudness50Hz:+4dB10kHz:+3dBRated power consumption400WExternal dimensionsWidth 460x Height 159x Depth 446 mmWeight33.0kg Technical Specifications -Serial: 601026121 -Country of Manufacture: Japan -Power Supply : 100V 400W 50/60Hz Voltage Please check the power requirements for this device and the specifications of your power supply. If you need to use this item in a 220-240 V environment, youll need a transformer. We sell high-quality Japanese compact transformers (Nissyo), which will allow you to use this item safely and with good performance in your country. IMPORT TAX ?Import duties, taxes, and other charges which are not included in the item price or shipping charges are the buyer’s responsibility. ?Please check with your country’s customs office to determine what these additional costs will be before bidding or buying. This item is sold As-DescribedThis item is sold As-Described and cannot be returned unless it arrives in a condition different from how it was described or photographed

This pre-main amplifier is completed by carefully refining and combining the three factors of circuit, mechanism and parts.The power stage adopts NM-LAPT (Non Magnetic Liner Amplification Power Transistor) developed as a power transistor exclusively for audio.The NM-LAPT is made of pure copper material all the way up to the bonding wire, and realizes excellent high-frequency characteristics and high current limit value by manufacturing cut-off frequency (fT) and fracture resistance (PC).Since the ground circuit of the power supply circuit is connected to the ground circuit of the amplifier circuit (negative output), we have introduced the original advanced ? -X balance circuit to prevent the reverse current from the speaker side from flowing into the amplifier circuit and the deterioration of sound quality.The amplifier circuit is completely independent from the ground circuit, and is balanced in such a way that transmission and amplification are carried out simultaneously, so that the circuit itself blocks out external noise and in-phase distortion.The dynamic frequency characteristics are also improved by reducing the impedance of the circuit to minimize the influence on the passing signal.In addition, a 4-amp configuration with dedicated amplifiers on the + side and - side each provides a push-pull system that drives from both directions under the same conditions on the + side and - side, thereby obtaining strong sound at a low distortion rate.It further improves the perfection of the diamond actuation circuit in which - output can be taken out without phase inversion.The cascade connection of the first stage FET realizes a wide range and high speed with excellent wide-area characteristics and greatly reduces the effect caused by impedance differences with external devices.We have developed a new power transformer (IDEAL SILENT POWER TRANSFORMER) and a capacitor for power supply, and have succeeded in greatly improving power supply capability and stability.Both primary and secondary transformers use OFC lead wires to minimize magnetic induction (?????????). The transformer weight is 13 kg because the shield is made of four layers of copper short rings, two layers of silicon steel plates and a squeeze case, high-density packing is used, and insulation materials are examined.The electrolytic condenser and fast recovery diode have also been completely changed to the one exclusively for the highest sound quality.All custom-made, low-impedance, clean NEW ? -X balanced power supplies and a closed-loop configuration independent of ground minimize the negative effects of unbalanced power supplies on music signals.The power supply unit is placed in the center and the power units are arranged symmetrically with the introduction of reinforced twin monaural construction. Each part with improved strength prevents sound quality degradation due to vibration, and acquires excellent sound image localization and phase characteristics.In addition to vibration control by twin monaural construction, various components with high internal loss and vibration absorption effect are used abundantly, such as large insulators made of pure copper muku covered with felt, pure copper bases and copper-plated parts.In addition, we have newly adopted the isolation of pure copper material, which has conventionally been used between the transformer and the chassis, between the electrolytic capacitor and the chassis, and between the amplifier base and the bottom plate, etc., between the master volume and the chassis, between the radiator and the power board, and even the transformer, electrolytic capacitor, power board, and power board itself.As for the mounting structure of each part, for example, the case of the transformer is attached to the chassis instead of attaching the main body of the transformer directly to the chassis. We have succeeded in effectively blocking the transmission route of vibration by means of the opposed mechanical feedback.In order to improve sound quality, the quality of each part is also thoroughly pursued.In addition to the development of transformers and condensers, we have adopted rolled copper substrates for power boards and power supply boards, plated copper on rear panels, painted hoods with paint containing copper, and adopted bronze screws.All parts are designed to be non-magnetic, vibration-proof, low impedance and high speed.It is equipped with an input terminal that realizes high-purity transmission and amplification of digital sources by directly inputting audio signals to the power amplifier section.Since there is a balanced input in addition to the normal input, setting by balance transmission and amplification is possible by connecting with an external device with a balanced output.Equipped with a source power direct switch that transmits all line input signals directly to the power amplifier with one touch operation.Connect and amplify directly without passing through any accessory functions to reproduce the pure sound of the source.Equipped with a recording function for effective recording and listening when a CD player is connected to the Power Amp Direct.For example, you can listen to the source input to Normal 1 while back-recording a CD or other source connected to Normal 2.Equipped with all-gold plated input terminal, large speaker terminal, large insulator made of pure copper, real side wood, power cord / AC outlet with polarity display, etc. TypeIntegrated amplifierPower Amplifier UnitRated output (20 Hz to 20 kHzSimultaneous operation on both channels, THD0.003%)6 ? : 190W + 190W8 ? : 160W + 160WTotal harmonic distortion factor0.003% or Less (Rated Output, 20 Hz to 20 kHz, 8 ? Load)Frequency characteristicDC ~ 300 kHz, + 0 -3dB (at 1W Output)Cross modulation distortion factor0.003% or Less (at 8 ? Load)Damping factor150 (8 ?)Input Sensitivity / Impedance1V/5k ? (1 kHz)Signal-to-noise ratio120 dB or more (A network)Dynamic Power6 ? : 310W4 ? : 390W2 ? : 580WTIM (SAWTOOTH)Measurement limit value or lessSlew rate200 V / ? secRise time0.5 ? secInput Sensitivity / Impedance(1kHz)Phono MM : 2.5mV/47k ?Phono MC : 300 ? V/100 ?CD, Tuner, Line, Tape/DAT1 / 2 / 3 : 150mV/20k ?Phono maximum allowable inputMM(THD 0.01%):250mVMC(THD 0.1%):25mVFrequency Response (1W)Phono MM : 20 Hz to 20 kHz, ± 0.2 dBCD, Tuner, Line, Tape/DAT-1 / 2 / 3 : DC ~ 300 Hz, + 0 -3dBSignal-to-noise ratio (A network)Phono MM : 90 dB or morePhono MC : 75 dB or moreCD, Tuner, Line, Tape/DAT-1 / 2 / 3 : 110 dB or moreTone controlMaximum variation of BASS : + / - 5 dB at 50 HzMaximum change of TREBLE : ± 5 dB (15 kHz)Subsonic filter16 Hz (-3dB), 6dB/oct.Loudness50Hz:+4dB10kHz:+3dBRated power consumption400WExternal dimensionsWidth 460x Height 159x Depth 446 mmWeight33.0kg Technical Specifications -Serial: 601026121 -Country of Manufacture: Japan -Power Supply : 100V 400W 50/60Hz Voltage Please check the power requirements for this device and the specifications of your power supply. If you need to use this item in a 220-240 V environment, youll need a transformer. We sell high-quality Japanese compact transformers (Nissyo), which will allow you to use this item safely and with good performance in your country. IMPORT TAX ?Import duties, taxes, and other charges which are not included in the item price or shipping charges are the buyer’s responsibility. ?Please check with your country’s customs office to determine what these additional costs will be before bidding or buying. This item is sold As-DescribedThis item is sold As-Described and cannot be returned unless it arrives in a condition different from how it was described or photographed

Item TitleSansui Landscape Stereo Integrated Lifier Au- 907Dr Payment Supports managed payments Please pay within 5 days after auction is finished. About Us We are located in Japan. Its our pleasure to make you happy by proposing our recommend item. If you have any questions or request about items please feel free to ask us. International Buyers - Please Note: -Import duties taxes and charges are not included in the item price or shipping charges. These charges are the buyers responsibility. -Please check with your countrys customs office to determine what these additional costs will be prior to bidding/buying. -These charges are normally collected by the delivering freight (shipping) company or when you pick the item up - do not confuse them for additional shipping charges. -We do not mark merchandise values below value or mark items as - gifts - The US and International government regulations prohibit such behavior. Thank you for your understanding.