Shunyata Research Venom 14 NR Digital with IEC C13 connection. Beats the pants off many quality power conditioners. Condition is Used. $399 New. Ships for Free. Includes original box and manuals. Specifically designed to be used with Digital only devices with no analog output to maximize noise reduction. From Shunyata.com: AWARDS & REVIEWS APPLICATIONSIdeal applications include devices that use very noisy switched mode power supplies (SMPS) including computer peripherals, music-servers, NAS arrays, routers, switches, monitors, clocks, up-samplers, digital transports, wall warts, and power bricks.Only available with US AC plugs. TECHNOLOGYNR NOISE REDUCTIONShunyata Research’s exclusive NR (Noise Reduction) technology is a multi-stage filter network that measurably reduces power-line and component-generated noise, producing better purity of tone and clarity. It delivers a stunning background of silence to recordings, allowing the listener to hear into recordings as never before. Every nuance of meaningful content is revealed, bringing to life music’s most consequential moments as if the performers are in the room with the listener.DYNAMIC TRANSIENT CURRENT DELIVERYDTCD™ Analysis is a technique that measures instantaneous current through low impedance electrical conductors and contacts. Shunyata Research uses it to optimize the design, specification and construction of parts and materials to ensure maximum current delivery performance. Each part, conductor, noise circuit and material allows for maximum throughput of instantaneous current.Listeners will experience earth-shaking low-frequency performance from even the highest-current amplifiers as well as dynamic contrasts unheard of outside of a live event. More than any other design parameter, Shunyata Research’s skill in eliminating resistance and maximizing peak-current delivery is unmatched.OFE Alloy 101Shunyata Research uses only the highest purity of copper available for the production of its wire products. OFE Alloy 101 or C10100 is the highest grade of copper with a minimum 99.99% purity and a conductivity rating of 101% IACS. OFE stands for oxygen-free electrolytic and supersedes the term OFHC (oxygen-free high conductivity). C10100 is the only grade of copper that comes with a written certification of purity.Certified by ASTM F68 C10100Fluorocarbon dielectrics are usually only found in wire used in the aerospace industry, satellites and only the most expensive audiophile cabling. It has special electrical characteristics; very low dielectric absorption, high dielectric strength and exceptional heat resistance. When used in audio and power cables is reduces the perception of dynamic compression and it improves sonic low-level resolution and clarity.Crystal clear transient detail.Audiophile Grade ConnectorsShunyata Research audiophile-grade connectors are made from a high-grade brass-copper-zinc alloy that can accept the very large 08 gauge conductors. The polycarbonate head-shells provide a lifetime of longevity.Hermetically SealedThe connectors are hermetically sealed with an electrically inert compound that protects the contacts and wires from corrosion. The compound also ensures that the wires cannot become loose, fray or pull out from the head shell. This guarantees a lifetime of reliable performance that does not degrade over time.KPIP™ PROCESSINGShunyata Research’s proprietary Kinetic Phase Inversion Process includes four days of continuous KPIP™ processing to dramatically reduce burn-in time and significantly improve sonic performance, delivering a relaxed and life-like presentation. SPECIFICATIONS Conductors: Wire: OFE 14 gaugeDielectric: PVCConnectors: IEC: C13 // C7 // C7p // C5Molded Hermetically SealedCrimped and soldered connectionsAC Plug: US NEMA P15Solid brass contacts (not folded metal)Nickel plating for corrosion protectionSuperior contact gripNOTE: AC plug: US NEMA type onlyNoise Reduction Technology:CCI™ Noise FilterMulti-stage arrayGreater than 12 dB @ 1 MHz noise reductionImpulse noise reduction: > 30 @ 1 MHzSafety Assurance:Continuity and Polarity Tests – by two techniciansHiPOT Tests for each cableCable spools tested for insulation breakdown @ 4,000 VACDimensions:Length: 1.75 metersNOTE: No custom lengths available DOWNLOADS:Venom NR / XC BrochureOUR ASSURANCESRELIABILITYOver more than 2 decades, the reliability and durability of Shunyata Research products has become a legendary attribute of the brand. Shunyata products are completely non-reactive and run cool to the touch. They do not hum, vibrate, buzz, or generate heat and do not require any ventilation. Despite heavy-use applications in studios, medical labs, and home environments, Shunyata Research products maintain an almost zero failure rate.QUALITYIn an era of products that are mass-produced, Shunyata Research invests in training career craftsman who build our products by hand at our factory in Poulsbo, Washington. The exceptional fit, finish, and attention to detail has become a hallmark trait of Shunyata Research products going back to its inception in 1998. Shunyata Research has been building some of the finest power and cable products in the industry for more than twenty years. The commitment to building durable products that are designed to last a lifetime elevates our products to the top of their class.SAFETYSafety and quality control is job one at Shunyata Research. Before anything leaves the factory, we test each and every product thoroughly and carefully for safety and quality. This explains the long-term success of Shunyata Research products in the professional recording, medical, scientific, and consumer industries. Shunyata Research’s impeccable product safety and reliability track record for the past 23 years speaks for itself.NO HUM — NO BUZZ — NO HEATLIMITED LIFETIME WARRANTY The unparalleled craftsmanship and build quality of Shunyata Research products is backed by a limited lifetime warranty. This demonstrates our commitment to building the finest products on the planet and providing exceptional customer support. VALID ONLY IN THE US AND CANADA

This Audio Research SP-14 tube amplifier is a high-quality preamplifier that delivers exceptional sound performance. The brand is well-known for their expertise in creating top-of-the-line audio equipment. The preamp is suitable for use in a home audio setup and is perfect for music enthusiasts who want to enjoy an immersive listening experience. This preamplifier is designed to work with other audio equipment such as receivers and amplifiers to enhance overall audio quality. It is a great choice for those who appreciate vintage audio equipment and want to add an old-school charm to their sound system. With its sleek and stylish design, this tube amplifier is sure to impress. Unit is very good working and sound excellent. The exterior has no noticeable dullness, scratches, nor damages. Packing will be carefully done to prevent a damage during the transit. Its a perfect working condition but will be sold as is, no return due to the age of the unit. The shipping will be fully insured. Thank you for looking.

Zwei Audio Research V140 Mono Endstufen. Wegen Umzug und Sammlungsverkleinerung zu verkaufen: Zwei rare Weltklasse AR V140 Mono 120 W an 4-16 Ohm. Spitzenklang. Röhrenendstufen aus Sammlung in top Zustand mit insgesamt 16 neuen gematchten 6550 Röhren. Wert der Röhren: über 1500€. Selten: Zwei Vollsynthetische AR Röhrenendstufen mit XLR Eingang. Vom deutschen Röhren-Guru H. LUA gekauft. Er hatte beide Endstufen zuvor mit neuen Röhren bestückt und eingemessen. Leistungsdaten 120 watts minimum continuous at 4-16 ohms from 20Hz to 20kHz with less than 1.0% total harmonic distortion (typically below .005% at 1 watt)! Wegen Umzug und Verkauf der Acapella Triolon nur kurze Zeit in Betrieb, seitdem trocken gelagert. Aufgrund des Gewichts und der Röhren, am liebsten aber persönliche Abholung. Probehören möglich an Acapella Violon, Cello Audio Suite,… Transport per Spedition. Achtung: 2 Pakete a ´ 35 kg!! oder 1x Palette a’ 75kg! Andere sichtbare Geräte sind nicht Gegenstand des Angebots. Sie bieten im Rahmen eines privaten Verkaufs unter Ausschluss von Garantie und Gewährleistung. Weitere Geräte, die ich Umzugsbedingt verkaufe, finden Sie ebenfalls auf eBay. International shipping possible. Please ask for shipping costs. Heavy weight 2x35 kg! Audio Research V140 Mono Tube Amps The V series power amplifiers represent an evolutionary refinement of the circuit topology first established in the acclaimed Classic amplifiers introduced by Audio Research a few years ago. While continuing to use triode operation and Audio Research's patented, cross-coupled circuit, the V amplifiers also incorporate a fully balanced input stage to minimize noise and distortion products that otherwise could degrade the musical resolution of the output stage. The input stage uses select J-FET transistors with MOSFET followers to provide ultra-quiet, low-impedance drive to the 6FQ7 dual triodes, which directly drive the output tubes. (The V amplifiers are shipped with matched, selected KT90 output tubes, although other popular alternative tube types are compatible: 6550. 6550A. KT88 or KT100.) 120 watts minimum continuous at 4-16 ohms from 20Hz to 20kHz with less than 1.0% total harmonic distortion (typically below .005% at 1 watt). Approximate actual power available at clipping: 125 watts (1kHz) (Note that the actual RMS power output is dependent upon both line voltage and condition ie: if power line has high distortion, maximum power will be affected adversely, although from a listening standpoint this is not very critical.)

ATTENTION! This auction is for AUDIO RESEARCH PREAMPLIFIER SP 14 ONLY!!!!! If you want to by extra AUDIO RESEARCH CLASSIC 60 - See My other auctions. The SP14s musicality comes surprisingly close to the state of the art, with soundstage of remarkable depth and breadth; imaging of uncanny solidity: palpable dynamic authority; timbral accuracy that virtually recreates live music; an exceptionally low noise floor; and a special ease with frequency extremes. But unlike many high-performance preamplifiers, the SP14 doesnt scrimp on control features. It has separate Gain and Attenuation for wide-ranging-yet-subtle level management. Separate Input and Record Output selectors (with a common menu) permit exceptional flexibility in playing and recording: owners can listen to one source while recording from another. The Bypass switch allows owners to remove the Balance and Mode controls from the signal path, for greater sonic purity. There are two separate sets of outputs, and three power outlets. And, of course, the SP14 features its own version of the hybrid technology that has made Audio Research electronics world-famous. As with every Audio Research product, SP14 parts quality, construction and factory support are the finest in the audio industry, with a two-decade track record to prove it. And all this comes at only half the cost of the celebrated SP15. FREQUENCY RESPONSEHigh-level section: ±.5dB, 5Hz to 50kHz, -3db points below 1Hz and above 200 kHz. Magnetic phono: ±.3dB of RIAA, 30Hz to 40kHzDISTORTION (THD)Less than .01% at 2V RMS outputNOISE & HUMHigh level: (1) 70 µV RMS maximum residual unweighted wideband noise at main output with gain control minimum (98 dB below 5V RMS output) (2) More than 100dB below 1V RMS input (less than 7 µV equivalent input noise). Phono: 0.12 µV equivalent input noise, IHF weighted, shorted input (78dB below 1mV input).GAINPhono input to tape output: 46 dB. Phono input to main output: 66 dB. High-level inputs to tape output: 0 dB. High-level inputs to main output: 20 dB.INPUT IMPEDANCELine inputs: 50 K ohms. Phono: 47K ohms (provisions for any value below 47K ohms or added input capacitance for matching certain magnetic cartridges.)OUTPUT IMPEDANCE250 ohms main output, 1000 ohms recorder output. Recommended load 60K - 100K ohms and 100pF. (20K ohms minimum and 1000pF maximum)OUTPUT POLARITY-MAXIMUM INPUTSMagnetic phono, 200mV at 1kHz (1000mV RMS, 10 kHz). High-level inputs are essentially overload-proof.RATED OUTPUTS2V RMS 5 Hz to 50 kHz, all outputs; 60K ohm load (main output capability is 50V RMS output at .5% THD at 1kHz into a 100K ohm load with 5V RMS high level input)POWER SUPPLIESElectronically-regulated low and high voltage supplies and electronic decoupling. Shielded toroid transformer. Line regulation is better than .01%.TUBE COMPLEMENT(1) 6DJ8/ECC88POWER REQUIREMENTS100-135VAC 60Hz (200-270VAC 50/60Hz) 60 WattsOTHERHybrid FET/Tube audio circuit, solid-state power supply. Inputs (7): Phono, C-D, Tuner, Video, Spare, Tape 1, Tape 2. Outputs (4): (2) Main, (2) Recorder. Controls (6): Gain, Attenuation, Balance. Mode, Record Out, Input. Switches (8): Power, Outlets, Bypass, Mute, Copy, Tape 1 to 2/2 to 1, Tape 2/1, Monitor.DIMENSIONS19” (48 cm) W x 5 ¼” (13.4 cm) H (standard rack panel) x 10 ¼” (26 cm) D. Handles extend 1 ? (4.1 cm) forward of front panel. Rear chassis fittings extend ? (2.3 cm)WEIGHT12 lbs. (5.5kg) Net, 21 lbs. (9.6 kg) Shipping

ATTENTION! This auction is for AUDIO RESEARCH AMPLIFIER CLASSIC 60 ONLY!!!!! If you want to by extra AUDIO RESEARCH PREAMPLIFIER SP-14 - See My other auctions.The new Classic 60 Hybrid Stereo Power Amplifier resembles the long-popular D115 in Audio Researchs family of High Definition® power amplifiers. But its lineage is strictly Classic 150. Which means nothing less than state-of-the-art in design, construction, musicality, and operational convenience...at an affordable price. Like the Classic 150, the Classic 60 proceeds from the notion that power ratings dont always describe a power amplifiers real capabilities. Far more important are such qualities as dynamic stability. lucidity, subtlety. And to achieve those, Audio Research has used its traditional partial cathode coupling along with triode operation of the Classic 60s eight 6550 power output tubes. Additional circuit improvements, as well as the usual rigorous parts selection and manufacturing Audio Research, are noted for, also contributing sonically. Translated into the language of listening, this signifies stunning bandwidth, a noise floor virtually beneath audibility, and musically fulfilling SPLs at dramatically lower gain settings. Dynamics, timbres of individual instruments, soundstage, and musical emotion all surge out from a black velvet of silence. Simply put the Classic 60 resolves far more of a musical program than amplifiers rated at two, three, or four times its seemingly modest 60 WPC. But the Classic 60 is easily up to the task of driving all but the most demanding loudspeakers, even in spacious listening rooms. And while it shows modest preamplifiers in their best light, it also shines when coupled with premiere designs, such as Audio Researchs SP14 or SP15. Convenience figures are high on the Classic 60s list of attributes, as well. For example, the DC balance of the output tubes is maintained automatically, while tube biasing continuously adjusts to changes in incoming line voltage. Performance stays razor-sharp without bothersome tweaking or adjustments. And quiet fan cooling, along with triode operation, means significantly longer tube life. A Classic 60 owner can look forward to years of low-maintenance performance POWER OUTPUT60 watts minimum continuous at 16 ohms from 15Hz to 20kHz with less than 1.0% total harmonic distortion. Typically below .005% at 1 watt. The approximate actual power available at clipping: 62 watts. (1kHz) (Note that the actual RMS power output is dependent upon both line voltage and condition ie: if the power line has high distortion, maximum power will be affected adversely, although, from a listening standpoint, this is not very critical.)POWER BANDWIDTH(-3dB points): 12Hz to 40kHzFREQUENCY RESPONSE-INPUT SENSITIVITY.55V RMS for rated outputINPUT IMPEDANCE100K ohms, nominalOUTPUT TAPS-OUTPUT REGULATIONApproximately 0.3dB 16-ohm load to open circuitOVERALL NEGATIVE FEEDBACK20dBDAMPING FACTORApproximately 30DISTORTION-SLEW RATE20V/µsRISE TIME2.0 µsHUM & NOISELess than 2.0mV RMS - 84dB below-rated output (20kHz bandwidth unweighted, inputs shorted)POWER SUPPLY ENERGY STORAGEApproximately 280 joulesPOWER REQUIREMENTS105-125VAC 60Hz (210-250VAC 50Hz) 500 watts at rated output, 700 watts maximum, 370 watts at idleTUBE COMPLEMENT(4 matched pairs) 6550 power output, (4) 6FQ7/6CG7 driversDIMENSIONS19 (48 cm) W (standard rack panel) x 7 (18 cm) H x 15 ¾ (40 cm) D (front panel back). Handles extend 1 ? (4.1 cm) forward of the front panel. Output connectors extend 1 behind the rear panel.WEIGHT63 lbs (28.64 kg) Net, 76 lbs (34.55 kg) Shipping

ATTENTION! This auction is for AUDIO RESEARCH PREAMPLIFIER SP 14 ONLY!!!!! If you want to by extra AUDIO RESEARCH CLASSIC 60 - See My other auctions. The SP14s musicality comes surprisingly close to the state of the art, with soundstage of remarkable depth and breadth; imaging of uncanny solidity: palpable dynamic authority; timbral accuracy that virtually recreates live music; an exceptionally low noise floor; and a special ease with frequency extremes. But unlike many high-performance preamplifiers, the SP14 doesnt scrimp on control features. It has separate Gain and Attenuation for wide-ranging-yet-subtle level management. Separate Input and Record Output selectors (with a common menu) permit exceptional flexibility in playing and recording: owners can listen to one source while recording from another. The Bypass switch allows owners to remove the Balance and Mode controls from the signal path, for greater sonic purity. There are two separate sets of outputs, and three power outlets. And, of course, the SP14 features its own version of the hybrid technology that has made Audio Research electronics world-famous. As with every Audio Research product, SP14 parts quality, construction and factory support are the finest in the audio industry, with a two-decade track record to prove it. And all this comes at only half the cost of the celebrated SP15. FREQUENCY RESPONSEHigh-level section: ±.5dB, 5Hz to 50kHz, -3db points below 1Hz and above 200 kHz. Magnetic phono: ±.3dB of RIAA, 30Hz to 40kHzDISTORTION (THD)Less than .01% at 2V RMS outputNOISE & HUMHigh level: (1) 70 µV RMS maximum residual unweighted wideband noise at main output with gain control minimum (98 dB below 5V RMS output) (2) More than 100dB below 1V RMS input (less than 7 µV equivalent input noise). Phono: 0.12 µV equivalent input noise, IHF weighted, shorted input (78dB below 1mV input).GAINPhono input to tape output: 46 dB. Phono input to main output: 66 dB. High-level inputs to tape output: 0 dB. High-level inputs to main output: 20 dB.INPUT IMPEDANCELine inputs: 50 K ohms. Phono: 47K ohms (provisions for any value below 47K ohms or added input capacitance for matching certain magnetic cartridges.)OUTPUT IMPEDANCE250 ohms main output, 1000 ohms recorder output. Recommended load 60K - 100K ohms and 100pF. (20K ohms minimum and 1000pF maximum)OUTPUT POLARITY-MAXIMUM INPUTSMagnetic phono, 200mV at 1kHz (1000mV RMS, 10 kHz). High-level inputs are essentially overload-proof.RATED OUTPUTS2V RMS 5 Hz to 50 kHz, all outputs; 60K ohm load (main output capability is 50V RMS output at .5% THD at 1kHz into a 100K ohm load with 5V RMS high level input)POWER SUPPLIESElectronically-regulated low and high voltage supplies and electronic decoupling. Shielded toroid transformer. Line regulation is better than .01%.TUBE COMPLEMENT(1) 6DJ8/ECC88POWER REQUIREMENTS100-135VAC 60Hz (200-270VAC 50/60Hz) 60 WattsOTHERHybrid FET/Tube audio circuit, solid-state power supply. Inputs (7): Phono, C-D, Tuner, Video, Spare, Tape 1, Tape 2. Outputs (4): (2) Main, (2) Recorder. Controls (6): Gain, Attenuation, Balance. Mode, Record Out, Input. Switches (8): Power, Outlets, Bypass, Mute, Copy, Tape 1 to 2/2 to 1, Tape 2/1, Monitor.DIMENSIONS19” (48 cm) W x 5 ¼” (13.4 cm) H (standard rack panel) x 10 ¼” (26 cm) D. Handles extend 1 ? (4.1 cm) forward of front panel. Rear chassis fittings extend ? (2.3 cm)WEIGHT12 lbs. (5.5kg) Net, 21 lbs. (9.6 kg) Shipping

ATTENTION! This auction is for AUDIO RESEARCH AMPLIFIER CLASSIC 60 ONLY!!!!! If you want to by extra AUDIO RESEARCH PREAMPLIFIER SP-14 - See My other auctions.The new Classic 60 Hybrid Stereo Power Amplifier resembles the long-popular D115 in Audio Researchs family of High Definition® power amplifiers. But its lineage is strictly Classic 150. Which means nothing less than state-of-the-art in design, construction, musicality, and operational convenience...at an affordable price. Like the Classic 150, the Classic 60 proceeds from the notion that power ratings dont always describe a power amplifiers real capabilities. Far more important are such qualities as dynamic stability. lucidity, subtlety. And to achieve those, Audio Research has used its traditional partial cathode coupling along with triode operation of the Classic 60s eight 6550 power output tubes. Additional circuit improvements, as well as the usual rigorous parts selection and manufacturing Audio Research, are noted for, also contributing sonically. Translated into the language of listening, this signifies stunning bandwidth, a noise floor virtually beneath audibility, and musically fulfilling SPLs at dramatically lower gain settings. Dynamics, timbres of individual instruments, soundstage, and musical emotion all surge out from a black velvet of silence. Simply put the Classic 60 resolves far more of a musical program than amplifiers rated at two, three, or four times its seemingly modest 60 WPC. But the Classic 60 is easily up to the task of driving all but the most demanding loudspeakers, even in spacious listening rooms. And while it shows modest preamplifiers in their best light, it also shines when coupled with premiere designs, such as Audio Researchs SP14 or SP15. Convenience figures are high on the Classic 60s list of attributes, as well. For example, the DC balance of the output tubes is maintained automatically, while tube biasing continuously adjusts to changes in incoming line voltage. Performance stays razor-sharp without bothersome tweaking or adjustments. And quiet fan cooling, along with triode operation, means significantly longer tube life. A Classic 60 owner can look forward to years of low-maintenance performance POWER OUTPUT60 watts minimum continuous at 16 ohms from 15Hz to 20kHz with less than 1.0% total harmonic distortion. Typically below .005% at 1 watt. The approximate actual power available at clipping: 62 watts. (1kHz) (Note that the actual RMS power output is dependent upon both line voltage and condition ie: if the power line has high distortion, maximum power will be affected adversely, although, from a listening standpoint, this is not very critical.)POWER BANDWIDTH(-3dB points): 12Hz to 40kHzFREQUENCY RESPONSE-INPUT SENSITIVITY.55V RMS for rated outputINPUT IMPEDANCE100K ohms, nominalOUTPUT TAPS-OUTPUT REGULATIONApproximately 0.3dB 16-ohm load to open circuitOVERALL NEGATIVE FEEDBACK20dBDAMPING FACTORApproximately 30DISTORTION-SLEW RATE20V/µsRISE TIME2.0 µsHUM & NOISELess than 2.0mV RMS - 84dB below-rated output (20kHz bandwidth unweighted, inputs shorted)POWER SUPPLY ENERGY STORAGEApproximately 280 joulesPOWER REQUIREMENTS105-125VAC 60Hz (210-250VAC 50Hz) 500 watts at rated output, 700 watts maximum, 370 watts at idleTUBE COMPLEMENT(4 matched pairs) 6550 power output, (4) 6FQ7/6CG7 driversDIMENSIONS19 (48 cm) W (standard rack panel) x 7 (18 cm) H x 15 ¾ (40 cm) D (front panel back). Handles extend 1 ? (4.1 cm) forward of the front panel. Output connectors extend 1 behind the rear panel.WEIGHT63 lbs (28.64 kg) Net, 76 lbs (34.55 kg) Shipping

For sale is myAudio Research SP-14. Its its in like new condition physically and in functionality. It comes with the original tube and sounds absolutely amazing!

ATTENTION! This auction is for AUDIO RESEARCH PREAMPLIFIER SP 14 ONLY!!!!! If you want to by extra AUDIO RESEARCH CLASSIC 60 - See My other auctions. The SP14s musicality comes surprisingly close to the state of the art, with soundstage of remarkable depth and breadth; imaging of uncanny solidity: palpable dynamic authority; timbral accuracy that virtually recreates live music; an exceptionally low noise floor; and a special ease with frequency extremes. But unlike many high-performance preamplifiers, the SP14 doesnt scrimp on control features. It has separate Gain and Attenuation for wide-ranging-yet-subtle level management. Separate Input and Record Output selectors (with a common menu) permit exceptional flexibility in playing and recording: owners can listen to one source while recording from another. The Bypass switch allows owners to remove the Balance and Mode controls from the signal path, for greater sonic purity. There are two separate sets of outputs, and three power outlets. And, of course, the SP14 features its own version of the hybrid technology that has made Audio Research electronics world-famous. As with every Audio Research product, SP14 parts quality, construction and factory support are the finest in the audio industry, with a two-decade track record to prove it. And all this comes at only half the cost of the celebrated SP15. FREQUENCY RESPONSEHigh-level section: ±.5dB, 5Hz to 50kHz, -3db points below 1Hz and above 200 kHz. Magnetic phono: ±.3dB of RIAA, 30Hz to 40kHzDISTORTION (THD)Less than .01% at 2V RMS outputNOISE & HUMHigh level: (1) 70 µV RMS maximum residual unweighted wideband noise at main output with gain control minimum (98 dB below 5V RMS output) (2) More than 100dB below 1V RMS input (less than 7 µV equivalent input noise). Phono: 0.12 µV equivalent input noise, IHF weighted, shorted input (78dB below 1mV input).GAINPhono input to tape output: 46 dB. Phono input to main output: 66 dB. High-level inputs to tape output: 0 dB. High-level inputs to main output: 20 dB.INPUT IMPEDANCELine inputs: 50 K ohms. Phono: 47K ohms (provisions for any value below 47K ohms or added input capacitance for matching certain magnetic cartridges.)OUTPUT IMPEDANCE250 ohms main output, 1000 ohms recorder output. Recommended load 60K - 100K ohms and 100pF. (20K ohms minimum and 1000pF maximum)OUTPUT POLARITY-MAXIMUM INPUTSMagnetic phono, 200mV at 1kHz (1000mV RMS, 10 kHz). High-level inputs are essentially overload-proof.RATED OUTPUTS2V RMS 5 Hz to 50 kHz, all outputs; 60K ohm load (main output capability is 50V RMS output at .5% THD at 1kHz into a 100K ohm load with 5V RMS high level input)POWER SUPPLIESElectronically-regulated low and high voltage supplies and electronic decoupling. Shielded toroid transformer. Line regulation is better than .01%.TUBE COMPLEMENT(1) 6DJ8/ECC88POWER REQUIREMENTS100-135VAC 60Hz (200-270VAC 50/60Hz) 60 WattsOTHERHybrid FET/Tube audio circuit, solid-state power supply. Inputs (7): Phono, C-D, Tuner, Video, Spare, Tape 1, Tape 2. Outputs (4): (2) Main, (2) Recorder. Controls (6): Gain, Attenuation, Balance. Mode, Record Out, Input. Switches (8): Power, Outlets, Bypass, Mute, Copy, Tape 1 to 2/2 to 1, Tape 2/1, Monitor.DIMENSIONS19” (48 cm) W x 5 ¼” (13.4 cm) H (standard rack panel) x 10 ¼” (26 cm) D. Handles extend 1 ? (4.1 cm) forward of front panel. Rear chassis fittings extend ? (2.3 cm)WEIGHT12 lbs. (5.5kg) Net, 21 lbs. (9.6 kg) Shipping

ATTENTION! This auction is for AUDIO RESEARCH PREAMPLIFIER SP 14 ONLY!!!!! See My other auctions. The SP14s musicality comes surprisingly close to the state of the art, with soundstage of remarkable depth and breadth; imaging of uncanny solidity: palpable dynamic authority; timbral accuracy that virtually recreates live music; an exceptionally low noise floor; and a special ease with frequency extremes. But unlike many high-performance preamplifiers, the SP14 doesnt scrimp on control features. It has separate Gain and Attenuation for wide-ranging-yet-subtle level management. Separate Input and Record Output selectors (with a common menu) permit exceptional flexibility in playing and recording: owners can listen to one source while recording from another. The Bypass switch allows owners to remove the Balance and Mode controls from the signal path, for greater sonic purity. There are two separate sets of outputs, and three power outlets. And, of course, the SP14 features its own version of the hybrid technology that has made Audio Research electronics world-famous. As with every Audio Research product, SP14 parts quality, construction and factory support are the finest in the audio industry, with a two-decade track record to prove it. And all this comes at only half the cost of the celebrated SP15. FREQUENCY RESPONSEHigh-level section: ±.5dB, 5Hz to 50kHz, -3db points below 1Hz and above 200 kHz. Magnetic phono: ±.3dB of RIAA, 30Hz to 40kHzDISTORTION (THD)Less than .01% at 2V RMS outputNOISE & HUMHigh level: (1) 70 µV RMS maximum residual unweighted wideband noise at main output with gain control minimum (98 dB below 5V RMS output) (2) More than 100dB below 1V RMS input (less than 7 µV equivalent input noise). Phono: 0.12 µV equivalent input noise, IHF weighted, shorted input (78dB below 1mV input).GAINPhono input to tape output: 46 dB. Phono input to main output: 66 dB. High-level inputs to tape output: 0 dB. High-level inputs to main output: 20 dB.INPUT IMPEDANCELine inputs: 50 K ohms. Phono: 47K ohms (provisions for any value below 47K ohms or added input capacitance for matching certain magnetic cartridges.)OUTPUT IMPEDANCE250 ohms main output, 1000 ohms recorder output. Recommended load 60K - 100K ohms and 100pF. (20K ohms minimum and 1000pF maximum)OUTPUT POLARITY-MAXIMUM INPUTSMagnetic phono, 200mV at 1kHz (1000mV RMS, 10 kHz). High-level inputs are essentially overload-proof.RATED OUTPUTS2V RMS 5 Hz to 50 kHz, all outputs; 60K ohm load (main output capability is 50V RMS output at .5% THD at 1kHz into a 100K ohm load with 5V RMS high level input)POWER SUPPLIESElectronically-regulated low and high voltage supplies and electronic decoupling. Shielded toroid transformer. Line regulation is better than .01%.TUBE COMPLEMENT(1) 6DJ8/ECC88POWER REQUIREMENTS100-135VAC 60Hz (200-270VAC 50/60Hz) 60 WattsOTHERHybrid FET/Tube audio circuit, solid-state power supply. Inputs (7): Phono, C-D, Tuner, Video, Spare, Tape 1, Tape 2. Outputs (4): (2) Main, (2) Recorder. Controls (6): Gain, Attenuation, Balance. Mode, Record Out, Input. Switches (8): Power, Outlets, Bypass, Mute, Copy, Tape 1 to 2/2 to 1, Tape 2/1, Monitor.DIMENSIONS19” (48 cm) W x 5 ¼” (13.4 cm) H (standard rack panel) x 10 ¼” (26 cm) D. Handles extend 1 ? (4.1 cm) forward of front panel. Rear chassis fittings extend ? (2.3 cm)WEIGHT12 lbs. (5.5kg) Net, 21 lbs. (9.6 kg) Shipping

ATTENTION! This auction is for AUDIO RESEARCH AMPLIFIER CLASSIC 60 ONLY!!!!! See My other auctions.The new Classic 60 Hybrid Stereo Power Amplifier resembles the long-popular D115 in Audio Researchs family of High Definition® power amplifiers. But its lineage is strictly Classic 150. Which means nothing less than state-of-the-art in design, construction, musicality, and operational convenience...at an affordable price. Like the Classic 150, the Classic 60 proceeds from the notion that power ratings dont always describe a power amplifiers real capabilities. Far more important are such qualities as dynamic stability. lucidity, subtlety. And to achieve those, Audio Research has used its traditional partial cathode coupling along with triode operation of the Classic 60s eight 6550 power output tubes. Additional circuit improvements, as well as the usual rigorous parts selection and manufacturing Audio Research, are noted for, also contributing sonically. Translated into the language of listening, this signifies stunning bandwidth, a noise floor virtually beneath audibility, and musically fulfilling SPLs at dramatically lower gain settings. Dynamics, timbres of individual instruments, soundstage, and musical emotion all surge out from a black velvet of silence. Simply put the Classic 60 resolves far more of a musical program than amplifiers rated at two, three, or four times its seemingly modest 60 WPC. But the Classic 60 is easily up to the task of driving all but the most demanding loudspeakers, even in spacious listening rooms. And while it shows modest preamplifiers in their best light, it also shines when coupled with premiere designs, such as Audio Researchs SP14 or SP15. Convenience figures are high on the Classic 60s list of attributes, as well. For example, the DC balance of the output tubes is maintained automatically, while tube biasing continuously adjusts to changes in incoming line voltage. Performance stays razor-sharp without bothersome tweaking or adjustments. And quiet fan cooling, along with triode operation, means significantly longer tube life. A Classic 60 owner can look forward to years of low-maintenance performance POWER OUTPUT60 watts minimum continuous at 16 ohms from 15Hz to 20kHz with less than 1.0% total harmonic distortion. Typically below .005% at 1 watt. The approximate actual power available at clipping: 62 watts. (1kHz) (Note that the actual RMS power output is dependent upon both line voltage and condition ie: if the power line has high distortion, maximum power will be affected adversely, although, from a listening standpoint, this is not very critical.)POWER BANDWIDTH(-3dB points): 12Hz to 40kHzFREQUENCY RESPONSE-INPUT SENSITIVITY.55V RMS for rated outputINPUT IMPEDANCE100K ohms, nominalOUTPUT TAPS-OUTPUT REGULATIONApproximately 0.3dB 16-ohm load to open circuitOVERALL NEGATIVE FEEDBACK20dBDAMPING FACTORApproximately 30DISTORTION-SLEW RATE20V/µsRISE TIME2.0 µsHUM & NOISELess than 2.0mV RMS - 84dB below-rated output (20kHz bandwidth unweighted, inputs shorted)POWER SUPPLY ENERGY STORAGEApproximately 280 joulesPOWER REQUIREMENTS105-125VAC 60Hz (210-250VAC 50Hz) 500 watts at rated output, 700 watts maximum, 370 watts at idleTUBE COMPLEMENT(4 matched pairs) 6550 power output, (4) 6FQ7/6CG7 driversDIMENSIONS19 (48 cm) W (standard rack panel) x 7 (18 cm) H x 15 ¾ (40 cm) D (front panel back). Handles extend 1 ? (4.1 cm) forward of the front panel. Output connectors extend 1 behind the rear panel.WEIGHT63 lbs (28.64 kg) Net, 76 lbs (34.55 kg) Shipping

fidelity-research FR FR-S4 Machined Aluminum Block 14.6g Vintage Audio Domo Arigato! Welcome, Thank you for your visit. Description Operation confirmed. The appearance is a beautiful product without any noticeable scratches.For other appearances, please refer to the photo. 14.6g Shipping Shipping is only available to the address registered in eBay. Shipping is by FedEx or EMS. Free Shipping Returns Unconditional Return Policy Customer service and satisfaction are very important to us.I have an unconditional return policy if notified within 30 of the receipt of the item. All returned items must be the original condition.All return requests must be made within 30 days of the receipt of the item. Please contact me first for return before you ship it back to me.The postage of the returned goods is a buyer burden. International Buyers Please Note:Import duties, taxes and charges are not included in the item price or shipping charges.These charges are the buyer’s responsibility.Please check with your country’s customs office to determine what these additional costs will be prior to bidding/buying.These charges are normally collected by the delivering freight (shipping) company or when you pick the item up -do not confuse them for additional shipping charges.We do not mark merchandise values below value or mark items as “gifts” -US and International government regulations prohibit such behavior. I am sorry but we can not arrange that because it is illegal in Japan.Thank you.

Brand New/ Factory Sealed Etymotic ER2-SE earbuds / in-ear headphones. ER2SE is the IEM of choice for consumers who prefer to listen to their music exactly the way it was recorded.It is also a fantastic choice for audio creators and musicians, who require a precise and neutral sound reproduction. Dispatched within 1 working day, sent with either Royal Mail 1st class Signed or Tracked 24. Purchase from someone with a genuine interest in audiophile sound! ---------------------------------------------------- I am also selling £800 Active Hi-Fi Bookshelf Speakers for only £549. Search ebay for item number: 134577752231 ---------------------------------------------------- Check out my youtube channel, where I post Hi-Fi EQ settings for speakers and headphones: https://youtube.com/@MrCow99987

When Stereophile reviewed this preamp, they concluded it will set new standards for the industry. A quick listen and you will probably come to the same conclusion. Music reproduction was simply magical. Soundstage was large in scale with loads of detail and if you listen to a lot of vocals, the SP-14 is a gem. The level of performance it offered at its $3,000 MSRP then is a bargain now when you look at some of the current crop of $3,000 preamp. Design is a hybrid where one E88CC tube is used. Current tube inside is a Tesla E88CC which is renown for its warmth and overall performance. Previous owner had it serviced when some of the original resistors and caps were replaced. Some browning of the board is from the old resistors over heating but issue is resolved with new resistors. Cosmetically, it looks really nice with minor scuff marks from use but nothing major. Unit will be securely packed for safe shipping. Terms and conditions - PLEASE READ! Changes to PAYPAL refund: Due to recent policy changes at PAYPAL where they will not be refunding their portion of the PAYPAL fees, any refund that is requested to us will be treated likewise. In other words, when you send over a payment, the fee that PAYPAL takes out, will no longer be refunded back to you should you request a refund or we have to do a refund because you did not meet our transactional policy (like asking us to ship to a different address that is on the PAYPAL payment). We know this is unfair and have filed a complaint with Better Business Bureau. Hopefully, they will be able to “persuade” PAYPAL to drop this ridiculous policy. If you think this policy is ridiculous, pls contact your local BBB and file a similar complaint. That will add some weight to our filed complaint.TRANSACTIONS on eBay: ALL transactions must be completed on eBay. NO EXCEPTIONS. We will not respond to offers or suggestions on completing the transaction outside of eBay. Do not ask us to contact you directly outside eBay. If you find an item here on our eBay store that you are interested in purchasing, please conclude the transaction here on eBay.PRODUCT INFO: All items are fully tested and evaluated. If an item is not working properly, it will be mentioned in the listing. So read carefully. Cosmetic conditions will also be clearly laid out in the listing. But because everyone has a different standard, what is an 8/10 condition to me may be a 6/10 condition to you. So it is important you check out every picture on the listing. All pictures are of the actual item and taken just prior to listing it on eBay. All opinions expressed on our listings are our own and based on our evaluation in our system. They are not Gospel truth and should not be treated as such. Every system, every room and every conditions are different. We do not guarantee the result we get in our system will be the same in yours. WHAT KIND OF PRODUCTS WE SELL: We are a used hifi store so everything is used. So no warranty of any kind is offered or expressed. If there is a balance factory warranty from the manufacturer, you should check with them to see if it’s transferable. See above paragraph, everything is tested prior to selling and if there is any issue, we would list it in the listing. So it’s important you read every word in our listing. Occasionally, we may get dealer demo units, NOS (New Old Stock) or dealer excess inventory. Again, you need to check with the manufacturer if they will continue to honor any kind of warranty to you. PAYMENT INFO: PayPal payment is preferred and expected within 3 days after listing has closed. If payment is made through PAYPAL, we will ONLY ship to the address on the PAYPAL payment. NO EXCEPTIONS. SHIPPING: Item will be shipped within 24 hours of payment clearance except late Friday afternoon, Saturday, Sunday and Public Holidays. Tracking numbers will be provided on all shipments. We ship via FEDEX and USPS with insurance and signature required. In the very rare event that an item arrives not as described in our ads, we will resolve the issue(s) with the customer to their satisfaction. Returns are not accepted for shipping damage. If somehow the item arrives damaged, the buyer will need to inform us immediately so that we can get the claim process rolling. We will assist every way we can to get your money back. But this will be rare as we professionally pack every item that goes out to survive the rigor of shipping regardless of value. All orders will be insured and declared at full purchase value. If you want us to declare it at a lower value, you will need to fill out a form authorizing us to declare it at the amount you want us to and that you will assume all risk at the lowered value. And that includes insurance claim should the package be damaged or go missing during shipping. RETURNS: There are absolutely no returns for any items shipped outside the United States. International purchases for all items are as-is. The buyer assumes all cost of return shipping and handling. The only variation of this is if the item you receive is not the item you bought. In the rare event you have a change of mind (buyers remorse) after receiving the item; we may take the item back under our buy back quote or impose a re-stocking of 20% of the original purchase price. Cost of return shipping is your responsibility. This is a case to case basis and not an outright offer to accept every and any returns back. This is why it is important to read our listing carefully. Everything and anything is described in it with all pertinent information for you to make an informed decision. If you have any questions, ASK! DECLARED VALUE: All overseas purchases will be declared based on purchase price. NO EXCEPTION. This is because;1) For your protection as the declared value is also the insured value. 2) eBay and PAYPAL policies dictate that all declared value must be the purchase or transacted price.We know this may be tough in some countries because of your high duties so we will make exceptions but you need to contact us first and work out the details to complete your purchase. We will not entertain any requests after you have made the purchase and paid for it. PARTS OR REPAIRS: All items sold as parts or repairs are NOT returnable. Please read the listing carefully and understand what you are bidding/buying before committing. FRAUDULENT ACTIVITY: Due to recent actions by a few rotten apples we will be tagging all our items with tamper proof labels. If the labels are in any way removed or shows attempted action to remove it, we will be reporting the buyer to the relevant authorities for fraud. And if the buyer does a switch-a-roo where the labels have been removed or desecrated in any way, we will also report this fraudulent activity and will not honor any refunds or returns or exchanges.

When Stereophile reviewed this preamp, they concluded it will set new standards for the industry. A quick listen and you will probably come to the same conclusion. Music reproduction was simply magical. Soundstage was large in scale with loads of detail and if you listen to a lot of vocals, the SP-14 is a gem. The level of performance it offered at its $3,000 MSRP then is a bargain now when you look at some of the current crop of $3,000 preamp. Design is a hybrid where one E88CC tube is used. Current tube inside is a Tesla E88CC which is renown for its warmth and overall performance. Previous owner had it serviced when some of the original resistors and caps were replaced. Some browning of the board is from the old resistors over heating but issue is resolved with new resistors. Cosmetically, it looks really nice with minor scuff marks from use but nothing major. Unit will be securely packed for safe shipping. Terms and conditions - PLEASE READ! Changes to PAYPAL refund: Due to recent policy changes at PAYPAL where they will not be refunding their portion of the PAYPAL fees, any refund that is requested to us will be treated likewise. In other words, when you send over a payment, the fee that PAYPAL takes out, will no longer be refunded back to you should you request a refund or we have to do a refund because you did not meet our transactional policy (like asking us to ship to a different address that is on the PAYPAL payment). We know this is unfair and have filed a complaint with Better Business Bureau. Hopefully, they will be able to “persuade” PAYPAL to drop this ridiculous policy. If you think this policy is ridiculous, pls contact your local BBB and file a similar complaint. That will add some weight to our filed complaint.TRANSACTIONS on eBay: ALL transactions must be completed on eBay. NO EXCEPTIONS. We will not respond to offers or suggestions on completing the transaction outside of eBay. Do not ask us to contact you directly outside eBay. If you find an item here on our eBay store that you are interested in purchasing, please conclude the transaction here on eBay.PRODUCT INFO: All items are fully tested and evaluated. If an item is not working properly, it will be mentioned in the listing. So read carefully. Cosmetic conditions will also be clearly laid out in the listing. But because everyone has a different standard, what is an 8/10 condition to me may be a 6/10 condition to you. So it is important you check out every picture on the listing. All pictures are of the actual item and taken just prior to listing it on eBay. All opinions expressed on our listings are our own and based on our evaluation in our system. They are not Gospel truth and should not be treated as such. Every system, every room and every conditions are different. We do not guarantee the result we get in our system will be the same in yours. WHAT KIND OF PRODUCTS WE SELL: We are a used hifi store so everything is used. So no warranty of any kind is offered or expressed. If there is a balance factory warranty from the manufacturer, you should check with them to see if it’s transferable. See above paragraph, everything is tested prior to selling and if there is any issue, we would list it in the listing. So it’s important you read every word in our listing. Occasionally, we may get dealer demo units, NOS (New Old Stock) or dealer excess inventory. Again, you need to check with the manufacturer if they will continue to honor any kind of warranty to you. PAYMENT INFO: PayPal payment is preferred and expected within 3 days after listing has closed. If payment is made through PAYPAL, we will ONLY ship to the address on the PAYPAL payment. NO EXCEPTIONS. SHIPPING: Item will be shipped within 24 hours of payment clearance except late Friday afternoon, Saturday, Sunday and Public Holidays. Tracking numbers will be provided on all shipments. We ship via FEDEX and USPS with insurance and signature required. In the very rare event that an item arrives not as described in our ads, we will resolve the issue(s) with the customer to their satisfaction. Returns are not accepted for shipping damage. If somehow the item arrives damaged, the buyer will need to inform us immediately so that we can get the claim process rolling. We will assist every way we can to get your money back. But this will be rare as we professionally pack every item that goes out to survive the rigor of shipping regardless of value. All orders will be insured and declared at full purchase value. If you want us to declare it at a lower value, you will need to fill out a form authorizing us to declare it at the amount you want us to and that you will assume all risk at the lowered value. And that includes insurance claim should the package be damaged or go missing during shipping. RETURNS: There are absolutely no returns for any items shipped outside the United States. International purchases for all items are as-is. The buyer assumes all cost of return shipping and handling. The only variation of this is if the item you receive is not the item you bought. In the rare event you have a change of mind (buyers remorse) after receiving the item; we may take the item back under our buy back quote or impose a re-stocking of 20% of the original purchase price. Cost of return shipping is your responsibility. This is a case to case basis and not an outright offer to accept every and any returns back. This is why it is important to read our listing carefully. Everything and anything is described in it with all pertinent information for you to make an informed decision. If you have any questions, ASK! DECLARED VALUE: All overseas purchases will be declared based on purchase price. NO EXCEPTION. This is because;1) For your protection as the declared value is also the insured value. 2) eBay and PAYPAL policies dictate that all declared value must be the purchase or transacted price.We know this may be tough in some countries because of your high duties so we will make exceptions but you need to contact us first and work out the details to complete your purchase. We will not entertain any requests after you have made the purchase and paid for it. PARTS OR REPAIRS: All items sold as parts or repairs are NOT returnable. Please read the listing carefully and understand what you are bidding/buying before committing. FRAUDULENT ACTIVITY: Due to recent actions by a few rotten apples we will be tagging all our items with tamper proof labels. If the labels are in any way removed or shows attempted action to remove it, we will be reporting the buyer to the relevant authorities for fraud. And if the buyer does a switch-a-roo where the labels have been removed or desecrated in any way, we will also report this fraudulent activity and will not honor any refunds or returns or exchanges.