In great shape and working well.Lots of inputs.Does Pro Logic and hall and stadium surround modes.Two flaws there is a scratch on the top part of the cabinet and I have the remote but it doesnt work on the unit. I think the remote works because it lights up.It might be the remote sensor on the unit is bad. This is a killer amp,check out the specs. The “75-watt” rating of the Denon AV C-2000’s main outputs proved to be very conservative. At 1,000 Hz, the front outputs clipped at 114.3 watts into 8 ohms and at 178.5 watts into 4 ohms. Since the amplifier is rated only for 8-ohm service, we did not attempt continuous operation into 2 ohms. We did make dynamic power tests at all three impedance levels, measuring 121 watts into 8 ohms, 176 watts into 4 ohms, and an impressive 225 watts into 2 ohms. The THD plus noise, when the amplifier was driving 8 ohms at 75 watts, was 0.0085 to 0.01 percent from 20 to 8,000 Hz, reaching 0.015 percent at 20,000 Hz. Readings were slightly higher at lower power outputs because of the greater contribution of noise, reaching a maximum of 0.02 percent at 7.5 watts. At a constant 0.1-percent distortion, the amplifier delivered 65 watts into 8 ohms at 20 Hz, 90 watts from 1,000 to 10,000 Hz, and 75 watts at 20,000 Hz. With 4-ohm loads, the maximum output at 0.1-percent distortion was 100 watts at 20 Hz, 118 watts at 20,000 Hz, and 140 watts between 2,000 and 6,000 Hz. The frequency response through a high-level input was +0, —1 dB from 20 to 20,000 Hz, and the RIAA phono-equalization error was less than 0.1 dB from 200 to 20,000 Hz and — 1.2 dB at 20 Hz. The sensitivity, for a 1-watt reference output, was 18.5 millivolts (mv) through a high-level input and 0.35 mv through the phono input, with respective A-weighted noise levels of — 83.2 dB and —75.5 dB. The phono preamplifier overloaded at 170 mv input at 20 and 1,000 Hz and 157 mv at 20,000 Hz. The phono-input impedance was 47,000 ohms in parallel with 160 picofarads.

Hello, we will try our best to describe our items to the best of our ability, if you receive my item and its not as described please contact us before leaving any negative or neutral feedback I have for sale: Genuine OEM Denon UTU-200 CD Precision Audio Component/AM-FM Stereo Tuner Free Fast Shipping FREE FAST SHIPPING... Condition of the item: Used...Item works good, please look at the original photos... Includes: everything that is on pictures... We will try our best to describe our items to the best of our ability, if you receive my item and its not as described please contact us before leaving any negative or neutral feedback, Thank you Very much.

Great condition. One scuff in the front right corner as shown in picture. One day handling. Fast shipping.

In great shape and working well.Lots of inputs.Does Pro Logic and hall and stadium surround modes.Two flaws there is a scratch on the top part of the cabinet and I have the remote but it doesnt work on the unit. I think the remote works because it lights up.It might be the remote sensor on the unit is bad. This is a killer amp,check out the specs. The “75-watt” rating of the Denon AV C-2000’s main outputs proved to be very conservative. At 1,000 Hz, the front outputs clipped at 114.3 watts into 8 ohms and at 178.5 watts into 4 ohms. Since the amplifier is rated only for 8-ohm service, we did not attempt continuous operation into 2 ohms. We did make dynamic power tests at all three impedance levels, measuring 121 watts into 8 ohms, 176 watts into 4 ohms, and an impressive 225 watts into 2 ohms. The THD plus noise, when the amplifier was driving 8 ohms at 75 watts, was 0.0085 to 0.01 percent from 20 to 8,000 Hz, reaching 0.015 percent at 20,000 Hz. Readings were slightly higher at lower power outputs because of the greater contribution of noise, reaching a maximum of 0.02 percent at 7.5 watts. At a constant 0.1-percent distortion, the amplifier delivered 65 watts into 8 ohms at 20 Hz, 90 watts from 1,000 to 10,000 Hz, and 75 watts at 20,000 Hz. With 4-ohm loads, the maximum output at 0.1-percent distortion was 100 watts at 20 Hz, 118 watts at 20,000 Hz, and 140 watts between 2,000 and 6,000 Hz. The frequency response through a high-level input was +0, —1 dB from 20 to 20,000 Hz, and the RIAA phono-equalization error was less than 0.1 dB from 200 to 20,000 Hz and — 1.2 dB at 20 Hz. The sensitivity, for a 1-watt reference output, was 18.5 millivolts (mv) through a high-level input and 0.35 mv through the phono input, with respective A-weighted noise levels of — 83.2 dB and —75.5 dB. The phono preamplifier overloaded at 170 mv input at 20 and 1,000 Hz and 157 mv at 20,000 Hz. The phono-input impedance was 47,000 ohms in parallel with 160 picofarads.