This is a creampuff, mint condition. I have enjoyed this amp for a couple years before I moved to another state. It has been in environmentally controlled storage since Dec 2019. I just dont have the space in my current house for a stereo system, which this was a part of in my previously larger home. It is in the original packaging with box and styrofoam. I unboxed it and it works as great as the day I packed it up. No scratches, dents, or any issues. Sounds great! This auction is just for the power amp, the preamp is separate auction.The last photo is a stock photo from Audioholics. Topology: Fully discrete, dual differential, high current, short signal path Class A/B. Number of Channels: 2 Power Output (rated power; THD 0.05%): 125 watts / channel (8 ohms; all channels driven). 200 watts / channel (4 ohms; all channels driven). Rated Power Bandwidth (at rated power; 8 Ohm load): 10 Hz to 20 kHz + / - 0.1 dB. Minimum Recommended Load Impedance: 4 ohms (which equals one 4 ohm load or two paralleled 8 ohm loads per channel). Frequency Response: 5 Hz to 80 kHz + 0 / - 2 dB. THD + N: < 0.03% Signal to Noise Ratio (8 Ohm load): 92 dB at 1 watt (A-weighted). 106 dB at rated power (A-weighted). Damping Factor (8 Ohm load): 500 Speaker Output Connections: Full-sized 5-way binding posts; one pair per channel x 2. Power Supply: 350 VA high current ultra-low noise toroidal power transformer. 40,000 uF of storage capacitance. Input sensitivity (for rated power; 8 Ohm load): 1.1 V (for full output; 8 ohms). Gain: 29 dB Input Connections: Unbalanced (RCA); one per channel. Input Impedance: 47 kOhms Trigger: Trigger Input: 5 - 20 V (AC or DC); < 10 mA input current required. Trigger Output: 12 VDC; can drive any load up to 50 mA. Power Requirements: 115 VAC or 230 VAC +/- 10% @ 50 / 60 Hz (automatically detected and switched). Front Panel Controls and Indicators: Standby; push button (changes color to indicate Standby or On). Status LEDs (one per channel); illuminate blue for normal operation or red to indicate a fault (may be disabled by rear panel Status LED switch). Rear Panel Controls: AC Power switch; rocker switch (switches AC mains power). Status LEDs switch; small slide switch on left rear (disables front panel Status LEDs). Protection: The UPA-200 is protected against excessive operating temperature, shorted speaker connections, ground faults, and other common fault conditions. If a fault occurs, the UPA-200 will return to Standby mode, the Standby push button will light amber, and the Status LEDs will flash red. Size: unboxed: 17 wide x 3.375 high x 16.5 deep Weight: 24 lbs (net); 32 lbs (boxed) Features: A true audiophile-quality stereo amplifier. Advanced engineering with SMD gain blocks. Wideband, short signal path, class A/B design topology. Top quality parts and construction. Real power easily drives complex loads. Heavy-duty power supply with oversized toroidal transformer. Gold plated five way binding post speaker terminals. Gold plated RCA input terminals. Classic Emotiva styling with rugged solid steel chassis. 15mm solid milled aluminum faceplate. Channel status LED’s. (which can be disabled in stealth mode). Remote trigger input and output. 115 VAC or 230 VAC with automatic detection and switching. Full protection from all common input and output fault conditions. Ship to USA only, payment due within 2 days of auctions end.

This is a creampuff, mint condition. I have enjoyed this amp for a couple years before I moved to another state. It has been in environmentally controlled storage since Dec 2019. I just dont have the space in my current house for a stereo system, which this was a part of in my previously larger home. It is in the original packaging with box and styrofoam. I unboxed it and it works as great as the day I packed it up. No scratches, dents, or any issues. Sounds great! This auction is just for the power amp, the preamp is separate auction.The last photo is a stock photo from Audioholics. Topology: Fully discrete, dual differential, high current, short signal path Class A/B. Number of Channels: 2 Power Output (rated power; THD 0.05%): 125 watts / channel (8 ohms; all channels driven). 200 watts / channel (4 ohms; all channels driven). Rated Power Bandwidth (at rated power; 8 Ohm load): 10 Hz to 20 kHz + / - 0.1 dB. Minimum Recommended Load Impedance: 4 ohms (which equals one 4 ohm load or two paralleled 8 ohm loads per channel). Frequency Response: 5 Hz to 80 kHz + 0 / - 2 dB. THD + N: < 0.03% Signal to Noise Ratio (8 Ohm load): 92 dB at 1 watt (A-weighted). 106 dB at rated power (A-weighted). Damping Factor (8 Ohm load): 500 Speaker Output Connections: Full-sized 5-way binding posts; one pair per channel x 2. Power Supply: 350 VA high current ultra-low noise toroidal power transformer. 40,000 uF of storage capacitance. Input sensitivity (for rated power; 8 Ohm load): 1.1 V (for full output; 8 ohms). Gain: 29 dB Input Connections: Unbalanced (RCA); one per channel. Input Impedance: 47 kOhms Trigger: Trigger Input: 5 - 20 V (AC or DC); < 10 mA input current required. Trigger Output: 12 VDC; can drive any load up to 50 mA. Power Requirements: 115 VAC or 230 VAC +/- 10% @ 50 / 60 Hz (automatically detected and switched). Front Panel Controls and Indicators: Standby; push button (changes color to indicate Standby or On). Status LEDs (one per channel); illuminate blue for normal operation or red to indicate a fault (may be disabled by rear panel Status LED switch). Rear Panel Controls: AC Power switch; rocker switch (switches AC mains power). Status LEDs switch; small slide switch on left rear (disables front panel Status LEDs). Protection: The UPA-200 is protected against excessive operating temperature, shorted speaker connections, ground faults, and other common fault conditions. If a fault occurs, the UPA-200 will return to Standby mode, the Standby push button will light amber, and the Status LEDs will flash red. Size: unboxed: 17 wide x 3.375 high x 16.5 deep Weight: 24 lbs (net); 32 lbs (boxed) Features: A true audiophile-quality stereo amplifier. Advanced engineering with SMD gain blocks. Wideband, short signal path, class A/B design topology. Top quality parts and construction. Real power easily drives complex loads. Heavy-duty power supply with oversized toroidal transformer. Gold plated five way binding post speaker terminals. Gold plated RCA input terminals. Classic Emotiva styling with rugged solid steel chassis. 15mm solid milled aluminum faceplate. Channel status LED’s. (which can be disabled in stealth mode). Remote trigger input and output. 115 VAC or 230 VAC with automatic detection and switching. Full protection from all common input and output fault conditions. Ship to USA only, payment due within 2 days of auctions end.

DEFEKT-Gerät! Bitte kaufen Sie nicht wenn Sie nicht selbst zur Reparatur in der Lage sind! Defekt kaufen und in dieWerkstatt schleppen lohnt sich nie! Auch dieses Mal nicht! Fehlerbeschreibung nur als Anhaltspunkt! Wenn beispielsweise eine unverhofft festsitzende Schraube die nicht beschrieben ist ein Problem darstellt, bieten Sie nicht! Es kann immer malein weiteres Problem auftauchen, genau so gut wie es mit zwei Handgriffen erledigt sein kann. Defekt eben...Beschreibung:Ehemals wertigerStereo Vorverstärker wie im Titel benannt und original fotografiert. DEFEKT, lief kurz, hat sich dann mit Geräteneigung ausgeschaltet, beim abstellen ging er wieder an, und nun nicht mehr. Eigentlich ein gutes Gerät mit CD Direct und Phono MM/MC. Der abgebildete ist exakt der angebotene Pre-Amplifir. Bild zeigt den kompletten Auktionsumfang.Zustand: technisch defekt wie beschrieben. Äusserlich Front gut erhalten, Deckelblech OK, geringer verkratzt, vgl. Bilder. Kein Versand ausserhalb Deutschland. Kein Versand ausserhalb Deutschland. Versand nur an die bei eBay fest hinterlegte Versandadresse! Versand in die Europäische Union nur in Einzelfällen möglich (Produktabhängig). Nur DPD-Versand, Keine Packstation. No shipping outside Germany - were sorry!Sofort-Kaufen Anfragen zwecklos!English: item is not running! No remote. Abholung ist nicht möglich! etope 8

This is a creampuff, mint condition. I have enjoyed this amp for a couple years before I moved to another state. It has been in environmentally controlled storage since Dec 2019. I just dont have the space in my current house for a stereo system, which this was a part of in my previously larger home. It is in the original packaging with box and styrofoam. I unboxed it and it works as great as the day I packed it up. No scratches, dents, or any issues. Sounds great! This auction is just for the power amp, the preamp is separate auction.The last photo is a stock photo from Audioholics. Topology: Fully discrete, dual differential, high current, short signal path Class A/B. Number of Channels: 2 Power Output (rated power; THD 0.05%): 125 watts / channel (8 ohms; all channels driven). 200 watts / channel (4 ohms; all channels driven). Rated Power Bandwidth (at rated power; 8 Ohm load): 10 Hz to 20 kHz + / - 0.1 dB. Minimum Recommended Load Impedance: 4 ohms (which equals one 4 ohm load or two paralleled 8 ohm loads per channel). Frequency Response: 5 Hz to 80 kHz + 0 / - 2 dB. THD + N: < 0.03% Signal to Noise Ratio (8 Ohm load): 92 dB at 1 watt (A-weighted). 106 dB at rated power (A-weighted). Damping Factor (8 Ohm load): 500 Speaker Output Connections: Full-sized 5-way binding posts; one pair per channel x 2. Power Supply: 350 VA high current ultra-low noise toroidal power transformer. 40,000 uF of storage capacitance. Input sensitivity (for rated power; 8 Ohm load): 1.1 V (for full output; 8 ohms). Gain: 29 dB Input Connections: Unbalanced (RCA); one per channel. Input Impedance: 47 kOhms Trigger: Trigger Input: 5 - 20 V (AC or DC); < 10 mA input current required. Trigger Output: 12 VDC; can drive any load up to 50 mA. Power Requirements: 115 VAC or 230 VAC +/- 10% @ 50 / 60 Hz (automatically detected and switched). Front Panel Controls and Indicators: Standby; push button (changes color to indicate Standby or On). Status LEDs (one per channel); illuminate blue for normal operation or red to indicate a fault (may be disabled by rear panel Status LED switch). Rear Panel Controls: AC Power switch; rocker switch (switches AC mains power). Status LEDs switch; small slide switch on left rear (disables front panel Status LEDs). Protection: The UPA-200 is protected against excessive operating temperature, shorted speaker connections, ground faults, and other common fault conditions. If a fault occurs, the UPA-200 will return to Standby mode, the Standby push button will light amber, and the Status LEDs will flash red. Size: unboxed: 17 wide x 3.375 high x 16.5 deep Weight: 24 lbs (net); 32 lbs (boxed) Features: A true audiophile-quality stereo amplifier. Advanced engineering with SMD gain blocks. Wideband, short signal path, class A/B design topology. Top quality parts and construction. Real power easily drives complex loads. Heavy-duty power supply with oversized toroidal transformer. Gold plated five way binding post speaker terminals. Gold plated RCA input terminals. Classic Emotiva styling with rugged solid steel chassis. 15mm solid milled aluminum faceplate. Channel status LED’s. (which can be disabled in stealth mode). Remote trigger input and output. 115 VAC or 230 VAC with automatic detection and switching. Full protection from all common input and output fault conditions. Ship to USA only, payment due within 2 days of auctions end.

This is a creampuff, mint condition. I have enjoyed this amp for a couple years before I moved to another state. It has been in environmentally controlled storage since Dec 2019. I just dont have the space in my current house for a stereo system, which this was a part of in my previously larger home. It is in the original packaging with box and styrofoam. I unboxed it and it works as great as the day I packed it up. No scratches, dents, or any issues. Sounds great! This auction is just for the power amp, the preamp is separate auction.The last photo is a stock photo from Audioholics. Topology: Fully discrete, dual differential, high current, short signal path Class A/B. Number of Channels: 2 Power Output (rated power; THD 0.05%): 125 watts / channel (8 ohms; all channels driven). 200 watts / channel (4 ohms; all channels driven). Rated Power Bandwidth (at rated power; 8 Ohm load): 10 Hz to 20 kHz + / - 0.1 dB. Minimum Recommended Load Impedance: 4 ohms (which equals one 4 ohm load or two paralleled 8 ohm loads per channel). Frequency Response: 5 Hz to 80 kHz + 0 / - 2 dB. THD + N: < 0.03% Signal to Noise Ratio (8 Ohm load): 92 dB at 1 watt (A-weighted). 106 dB at rated power (A-weighted). Damping Factor (8 Ohm load): 500 Speaker Output Connections: Full-sized 5-way binding posts; one pair per channel x 2. Power Supply: 350 VA high current ultra-low noise toroidal power transformer. 40,000 uF of storage capacitance. Input sensitivity (for rated power; 8 Ohm load): 1.1 V (for full output; 8 ohms). Gain: 29 dB Input Connections: Unbalanced (RCA); one per channel. Input Impedance: 47 kOhms Trigger: Trigger Input: 5 - 20 V (AC or DC); < 10 mA input current required. Trigger Output: 12 VDC; can drive any load up to 50 mA. Power Requirements: 115 VAC or 230 VAC +/- 10% @ 50 / 60 Hz (automatically detected and switched). Front Panel Controls and Indicators: Standby; push button (changes color to indicate Standby or On). Status LEDs (one per channel); illuminate blue for normal operation or red to indicate a fault (may be disabled by rear panel Status LED switch). Rear Panel Controls: AC Power switch; rocker switch (switches AC mains power). Status LEDs switch; small slide switch on left rear (disables front panel Status LEDs). Protection: The UPA-200 is protected against excessive operating temperature, shorted speaker connections, ground faults, and other common fault conditions. If a fault occurs, the UPA-200 will return to Standby mode, the Standby push button will light amber, and the Status LEDs will flash red. Size: unboxed: 17 wide x 3.375 high x 16.5 deep Weight: 24 lbs (net); 32 lbs (boxed) Features: A true audiophile-quality stereo amplifier. Advanced engineering with SMD gain blocks. Wideband, short signal path, class A/B design topology. Top quality parts and construction. Real power easily drives complex loads. Heavy-duty power supply with oversized toroidal transformer. Gold plated five way binding post speaker terminals. Gold plated RCA input terminals. Classic Emotiva styling with rugged solid steel chassis. 15mm solid milled aluminum faceplate. Channel status LED’s. (which can be disabled in stealth mode). Remote trigger input and output. 115 VAC or 230 VAC with automatic detection and switching. Full protection from all common input and output fault conditions. Ship to USA only, payment due within 2 days of auctions end.

Pulled from my theater room setup is this powerful Emotiva UPA-200 Stereo Power Amplifier. Designed to deliver superior and clear sound, its perfect for audiophiles and music enthusiasts. With two channels, this amplifier can cater to your home audio needs and bring out the best in your sound system. The amplifier works and appears like new and was always cooled using an AC Infinity fan so you know it has not been exposed to high temperatures that might lean towards premature failure. I replaced this unit with a 4 channel unit for Atmos speakers, where this drove a 2 channel ATMOS setup previously. Made by Emotiva, a brand known for its high-quality audio products, this amplifier is a great addition to your home entertainment setup. Its model number is UPA-200, making it easy to find compatible accessories for your audio system. Get ready to enjoy your music like never before with this reliable power amplifier.

This is a creampuff, mint condition. I have enjoyed this amp for a couple years before I moved to another state. It has been in environmentally controlled storage since Dec 2019. I just dont have the space in my current house for a stereo system, which this was a part of in my previously larger home. It is in the original packaging with box and styrofoam. I unboxed it and it works as great as the day I packed it up. No scratches, dents, or any issues. Sounds great! This auction is just for the power amp, the preamp is separate auction.The last photo is a stock photo from Audioholics. Topology: Fully discrete, dual differential, high current, short signal path Class A/B. Number of Channels: 2 Power Output (rated power; THD 0.05%): 125 watts / channel (8 ohms; all channels driven). 200 watts / channel (4 ohms; all channels driven). Rated Power Bandwidth (at rated power; 8 Ohm load): 10 Hz to 20 kHz + / - 0.1 dB. Minimum Recommended Load Impedance: 4 ohms (which equals one 4 ohm load or two paralleled 8 ohm loads per channel). Frequency Response: 5 Hz to 80 kHz + 0 / - 2 dB. THD + N: < 0.03% Signal to Noise Ratio (8 Ohm load): 92 dB at 1 watt (A-weighted). 106 dB at rated power (A-weighted). Damping Factor (8 Ohm load): 500 Speaker Output Connections: Full-sized 5-way binding posts; one pair per channel x 2. Power Supply: 350 VA high current ultra-low noise toroidal power transformer. 40,000 uF of storage capacitance. Input sensitivity (for rated power; 8 Ohm load): 1.1 V (for full output; 8 ohms). Gain: 29 dB Input Connections: Unbalanced (RCA); one per channel. Input Impedance: 47 kOhms Trigger: Trigger Input: 5 - 20 V (AC or DC); < 10 mA input current required. Trigger Output: 12 VDC; can drive any load up to 50 mA. Power Requirements: 115 VAC or 230 VAC +/- 10% @ 50 / 60 Hz (automatically detected and switched). Front Panel Controls and Indicators: Standby; push button (changes color to indicate Standby or On). Status LEDs (one per channel); illuminate blue for normal operation or red to indicate a fault (may be disabled by rear panel Status LED switch). Rear Panel Controls: AC Power switch; rocker switch (switches AC mains power). Status LEDs switch; small slide switch on left rear (disables front panel Status LEDs). Protection: The UPA-200 is protected against excessive operating temperature, shorted speaker connections, ground faults, and other common fault conditions. If a fault occurs, the UPA-200 will return to Standby mode, the Standby push button will light amber, and the Status LEDs will flash red. Size: unboxed: 17 wide x 3.375 high x 16.5 deep Weight: 24 lbs (net); 32 lbs (boxed) Features: A true audiophile-quality stereo amplifier. Advanced engineering with SMD gain blocks. Wideband, short signal path, class A/B design topology. Top quality parts and construction. Real power easily drives complex loads. Heavy-duty power supply with oversized toroidal transformer. Gold plated five way binding post speaker terminals. Gold plated RCA input terminals. Classic Emotiva styling with rugged solid steel chassis. 15mm solid milled aluminum faceplate. Channel status LED’s. (which can be disabled in stealth mode). Remote trigger input and output. 115 VAC or 230 VAC with automatic detection and switching. Full protection from all common input and output fault conditions. Ship to USA only, payment due within 2 days of auctions end.

Emotiva UPA-200 Stereo Power Amplifier. Unit works great. Comes with power cord. Ships FEDEX, CONUS only. Worldwide shipping via ebay international shipping program.

This is a creampuff, mint condition. I have enjoyed this amp for a couple years before I moved to another state. It has been in environmentally controlled storage since Dec 2019. I just dont have the space in my current house for a stereo system, which this was a part of in my previously larger home. It is in the original packaging with box and styrofoam. I unboxed it and it works as great as the day I packed it up. No scratches, dents, or any issues. Sounds great! This auction is just for the power amp, the preamp is separate auction.The last photo is a stock photo from Audioholics. Topology: Fully discrete, dual differential, high current, short signal path Class A/B. Number of Channels: 2 Power Output (rated power; THD 0.05%): 125 watts / channel (8 ohms; all channels driven). 200 watts / channel (4 ohms; all channels driven). Rated Power Bandwidth (at rated power; 8 Ohm load): 10 Hz to 20 kHz + / - 0.1 dB. Minimum Recommended Load Impedance: 4 ohms (which equals one 4 ohm load or two paralleled 8 ohm loads per channel). Frequency Response: 5 Hz to 80 kHz + 0 / - 2 dB. THD + N: < 0.03% Signal to Noise Ratio (8 Ohm load): 92 dB at 1 watt (A-weighted). 106 dB at rated power (A-weighted). Damping Factor (8 Ohm load): 500 Speaker Output Connections: Full-sized 5-way binding posts; one pair per channel x 2. Power Supply: 350 VA high current ultra-low noise toroidal power transformer. 40,000 uF of storage capacitance. Input sensitivity (for rated power; 8 Ohm load): 1.1 V (for full output; 8 ohms). Gain: 29 dB Input Connections: Unbalanced (RCA); one per channel. Input Impedance: 47 kOhms Trigger: Trigger Input: 5 - 20 V (AC or DC); < 10 mA input current required. Trigger Output: 12 VDC; can drive any load up to 50 mA. Power Requirements: 115 VAC or 230 VAC +/- 10% @ 50 / 60 Hz (automatically detected and switched). Front Panel Controls and Indicators: Standby; push button (changes color to indicate Standby or On). Status LEDs (one per channel); illuminate blue for normal operation or red to indicate a fault (may be disabled by rear panel Status LED switch). Rear Panel Controls: AC Power switch; rocker switch (switches AC mains power). Status LEDs switch; small slide switch on left rear (disables front panel Status LEDs). Protection: The UPA-200 is protected against excessive operating temperature, shorted speaker connections, ground faults, and other common fault conditions. If a fault occurs, the UPA-200 will return to Standby mode, the Standby push button will light amber, and the Status LEDs will flash red. Size: unboxed: 17 wide x 3.375 high x 16.5 deep Weight: 24 lbs (net); 32 lbs (boxed) Features: A true audiophile-quality stereo amplifier. Advanced engineering with SMD gain blocks. Wideband, short signal path, class A/B design topology. Top quality parts and construction. Real power easily drives complex loads. Heavy-duty power supply with oversized toroidal transformer. Gold plated five way binding post speaker terminals. Gold plated RCA input terminals. Classic Emotiva styling with rugged solid steel chassis. 15mm solid milled aluminum faceplate. Channel status LED’s. (which can be disabled in stealth mode). Remote trigger input and output. 115 VAC or 230 VAC with automatic detection and switching. Full protection from all common input and output fault conditions. Ship to USA only, payment due within 2 days of auctions end.

Fully working in excellent condition. The system sounds very musical and very convenient to use. They come with the original remote. The item(s) will be carefully packed and safe delivery is guaranteed. PayPal is preferred. All items should be paid within 2 days after the auction, unless prior arrangements are made! Shipping cost listed above is for US continental 48 states only and the buyer is subject to additional shipping cost outside the US continental 48 states. International buyers are subject to additional shipping cost per Ebays Global Shipping Program. Thanks for looking and feel free to ask questions!

** If you have a Feedback score of 20 or less, do not purchase this, your transaction will be cancelled** **If Buyer info doesnt match with Ship To info, the transaction will be cancelled** Please read above statements and understand before purchase. Very Good condition Emotiva UPA 200. Comes with a Pangea power cord I upgraded this to. Shipping to contiguous 48, no international shipping.. Specs:Fully discrete, dual differential, high current, short signal path Class A/B. Number of Channels: 2 Power Output (rated power; THD 0.05%): 125 watts / channel (8 ohms; all channels driven). 200 watts / channel (4 ohms; all channels driven).Rated Power Bandwidth (at rated power; 8 Ohm load): 10 Hz to 20 kHz + / - 0.1 dB. Will ship UPS by default,or can use FedEx if you prefer. I dont use Usps. No refunds, this is being sold As-Is, as it is a older used amplifier close to 12 years old now. Buy with confidence, I have perfect feedback since 2005 Can be picked up locally to me in the DFW area, zip code 75075. Thanks.

EMOTIVA UPA-200POWER AMPLIFIER 2-CHANNELS100 WATTS PER SIDE VERY GOOD CONDITION IF YOU HAVE ANY QUESTIONSPLEASE FEEL FREE TO ASKBEFORE BIDDING THANK YOU & GOOD LUCK

Wahrscheinlich handelt es sich hier um die einmalige Gelegenheit, eine originalverpackte, ungenutzte UHER UPA-200 zu kaufen. Die UHER UPA-200 wurde zwischen 1989 und 1991 gebaut und zhlt zu den heute noch sehr beliebten Vorverstrkern in der Hifi Szene. Das besondere an diesem Exemplar ist der Zustand. Dieser ergibt sich aus der Geschichte des Vorverstrkers. Denn die UPA wurde vor gut 33 Jahren gekauft und dann in Originalverpackung mit original Zubehr und Bedienungsanleitung in einem Schrank aufbewahrt. Sie besitzt daher einen neuwertigen Zustand. Es ist so, als sei sie erst vor drei Wochen bei Harman vom Band gefallen. Ich vermute, das gibt es so kein zweites Mal. Ich habe die Funktionen trotzdem alle getestet, und wie es zu erwarten war, funktioniert alles wie am ersten Tag. Trotzdem mchte ich es erwhnen: Die Garantiezeit ist vorbei . Daher.... Der Kaufgegenstand wird unter Ausschluss jeglicher Gewhrleistung verkauft. Der Ausschluss gilt nicht fr Schadensersatzansprche aus grob fahrlssiger bzw. vorstzlicher Verletzung von Pflichten des Verkufers sowie fr jede Verletzung von Leben, Krper und Gesundheit.

Perfect condition. Includes power cord. $300 + $50 shipping to CONUS. No International shipping.

** If you have a Feedback score of 20 or less, do not purchase this, your transaction will be cancelled** **If Buyer info doesnt match with Ship To info, the transaction will be cancelled** Please read above statements and understand before purchase. Very Good condition Emotiva UPA 200. Comes with a Pangea power cord I upgraded this to. Shipping with insurance to contigious 48, no international shipping.. Specs:Fully discrete, dual differential, high current, short signal path Class A/B. Number of Channels: 2 Power Output (rated power; THD 0.05%): 125 watts / channel (8 ohms; all channels driven). 200 watts / channel (4 ohms; all channels driven).Rated Power Bandwidth (at rated power; 8 Ohm load): 10 Hz to 20 kHz + / - 0.1 dB. Will ship UPS by default, or can use FedEx if you prefer. I dont use Usps. *******************************************************Will be shipped once Ebay releases funds, usually within 5 days of purchase date. The additional days are in addition to the 3 days Ebay Allows for shipping. If you do not agree with this, dont buy it. I dont consider my items paid for, until funds are released to me by Ebay. ********************************************************* No refunds, this is being sold As-Is, as it is a older used amplifier close to 12 years old now. Buy with confidence, I have perfect feedback Can be picked up locally to me in the DFW area, zip code 75075. Thanks.

Everything has been tested. All functions are working. I do have the speakers as well For this set. If you are interested in them please message and we can work that into the deal Please check out our eBay store. We have over 1000+ listing and are adding more daily! Sold as is. Everything you see in the pictures is what is included in this lot. Photos are the best description. Please look at ALL pictures closely before purchasing. We will document any damage the best we can but the photos will always be the best way to exam the item. Items may need a more in depth cleaning. We will do our best to clean every item, although sometimes we can’t do a full thorough clean. Message us for additional photos or questions. We are a large store please allow up to 3 business days for your item to go out. We of course will get them out as fast as we can. If you ever have a concern, PLEASE MESSAGE US before leaving negative feedback. We will help resolve whatever issue you are having. We try very hard to provide good communication and always strive for everyone to have a positive experiences!

Everything has been tested. All functions are working. I do have the speakers as well For this set. If you are interested in them please message and we can work that into the deal Please check out our eBay store. We have over 1000+ listing and are adding more daily! Sold as is. Everything you see in the pictures is what is included in this lot. Photos are the best description. Please look at ALL pictures closely before purchasing. We will document any damage the best we can but the photos will always be the best way to exam the item. Items may need a more in depth cleaning. We will do our best to clean every item, although sometimes we can’t do a full thorough clean. Message us for additional photos or questions. We are a large store please allow up to 3 business days for your item to go out. We of course will get them out as fast as we can. If you ever have a concern, PLEASE MESSAGE US before leaving negative feedback. We will help resolve whatever issue you are having. We try very hard to provide good communication and always strive for everyone to have a positive experiences!

Very Good condition Emotiva UPA 200. Comes with a Pangea power cord I upgraded this to. Shipping with insurance to contigious 48, no international shipping.. Specs: Fully discrete, dual differential, high current, short signal path Class A/B. Number of Channels: 2 Power Output (rated power; THD 0.05%): 125 watts / channel (8 ohms; all channels driven). 200 watts / channel (4 ohms; all channels driven). Rated Power Bandwidth (at rated power; 8 Ohm load): 10 Hz to 20 kHz + / - 0.1 dB. Will ship UPS by default, , or can use FedEx if you prefer. I dont use Usps. No refunds, this is being sold As-Is and is a used Amplifier. Buy with confidence, I have perfect feedback and go the extra mile on packing when I ship something. Can be picked up locally to me in the DFW area, zip code 75075. Thanks.