Practically brand new. Purchased 7 months ago from emotiva. MSRP is $2300 plus Tax. Perfect working condition. Includes original power cable, and box. Amplifier is amazing! But I need more channels and I don’t have a spot for a second amp sadly otherwise I’d never sell!! Will ship same day as purchase. Thanks! Circuit Topology A fully modular, fully differential, fully balanced audio power amplifier with a high-efficiency switch mode power supply (SMPS), independent, fully discrete, dual differential, high current, short signal path Class A/B amplifier modules, Optimized Class H™ power supply topology, and microprocessor-controlled fault protection. NOTE: This is a fully balanced amplifier with a floating, differential output stage. The output terminals must NEVER be tied together or ground referenced. Doing so will cause immediate damage that is NOT covered under warranty. If you have any questions about speaker compatibility, please contact Emotiva for technical support. Audio Specifications The XPA-DR3 features three Differential Reference™ Amplifier Modules. Audio Specifications (Three Differential Reference Amplifier Modules): Power Output (all three channels driven): 450 watts RMS, per channel, into 8 Ohms, at <0.1% THD. 600 watts RMS, per channel, into 4 Ohms, at <0.1% THD. Power Bandwidth (at rated power; 4 Ohm - 8 Ohm load): 20 Hz to 20 kHz (+ / – 0.1 dB). Broad Band Frequency Response: 20 Hz to 50 kHz +0/-2 dB. THD + noise: < 0.015%; at 100 watts RMS; 1 kHz; 8 Ohms. Signal to Noise Ratio (8 Ohm load): > 120 dB; ref FTC rated power; unbalanced input (A-weighted). > 96 dB; ref 1 watt; unbalanced input (A-weighted). Minimum Recommended Load Impedance (per channel): 4 Ohms (which equals one 4 Ohm load or two paralleled 8 Ohm loads). Damping Factor (8 Ohm load): > 500. Input Sensitivity (for rated power; 8 Ohm load): 2.0 V. Gain: 29 dB. Maximum Power Consumption: 2,300 watts. Note: The values shown refer to the amount of power the amplifier would consume while playing test tones continuously, on all channels, at full power, into a load bank. Therefore they are not at all characteristic of what you would expect when playing music or the sound track from a movie. Normal audio signals are dynamic, so the amount of power they require from second to second varies widely, and the average is far lower than this. With normal content, even playing very loudly, one of our amplifiers will consume far less power than indicated in the chart, so these values should not be considered to be a circuit requirement for normal operation. Input Impedance: 33 kOhms (balanced). 23.5 kOhms (unbalanced). Input And Output Connections Input Connections: Unbalanced (RCA); balanced (XLR); one each, per channel, user selectable. Speaker Output Connections: Audiophile grade, gold plated, 5-way binding posts. Trigger: Trigger Input: 5 – 12 V (AC or DC); <10 mA input current required. Trigger Output: 12 VDC; can drive any load up to 120 mA. Power Requirements Between 100 VAC and 250 VAC @ 50 / 60 Hz (automatically detected). Front Panel Controls and Indicators Standby: push button (halo ring changes color to indicate Standby or On). Status LEDs: one per channel; blue. Status LEDs change to red to indicate a fault condition. Rear Panel Controls AC Power switch: rocker switch (switches AC main power). Status LEDs switch: disables front panel Status LEDs and dims Standby button halo. Input selector switches (one per channel): metal toggle switches; select between balanced and unbalanced inputs. Circuit Breaker: press button to reset circuit breaker. Protection The XPA-DR3 is protected against excessive operating temperature, shorted speaker connections, ground faults, and other common fault conditions. Mechanical Dimensions: 17” wide x 8” high x 19” deep (unboxed; including feet). 17” wide x 7” high x 19” deep (unboxed; without feet). 24-1/2” wide x 12” high x 24-3/4” deep (boxed). Weight: 49.5 lbs (unboxed). 54.5 lbs (boxed).

Emotiva XPA-DR3 Differential Reference true balanced differential. Condition is Used. Shipped with USPS Ground Advantage. The item is in very condition overall.

3-Channel 450 watts RMS, per channel, 600 watts RMS, per channel, into 4 Ohms, A fully modular, fully differential, fully balanced audio power amplifier with a high-efficiency switch mode power supply (SMPS), independent, fully discrete, dual differential, high current, short signal path Class A/B amplifier modules, Optimized Class H™ power supply topology, and microprocessor-controlled fault protection.

Up for Auction is an Emotiva XPA-DR3 Differential Reference Three-Channel Power Amplifier. This BEAST comes with plenty of power to run your front soundstage. See specs below. This was purchased new from Emotiva for a dedicated theater this past year but we are moving and will no longer be building a theater room. This also comes with the Emotiva Rack Ears as well. This amplifier is $2300 on Emotivas site so its a great opportunity to purchase new at a great discount. Please feel free to ask any questions and check out my other home theater listings with amplifiers from Emotiva, a Audioquest Power conditioner, an Anthem Processor, an Epson 5040 Projector, and a JVC NZ7 Laser Projector. EVERYTHING IS PRICED TO SELL, FEEL FREE TO SEND APPROPRIATE OFFERS TO END AUCTION EARLY. Thank you The XPA-DR3 is a high-powered three-channel audiophile power amplifier that combines the exceptional accuracy and finesse of a true balanced differential design with the power you need to deliver musical crescendos and movie special effects with stunning realism and impact. Whatever your listening preferences, the XPA-DR3 will give you the combination of detail and power than only a fully differential amplifier can provide.The XPA-DR3 features three of our Differential Reference™ Amplifier Modules, and is the ideal choice to power the critical front three channels of an absolutely awesome surround sound music or home theater system. The XPA-DR3 delivers 450 watts RMS into 8 Ohms, and 600 watts RMS into 4 Ohms, all three channels driven, with less than 0.1% THD.The Power Supply: The Foundation Of A Great AmplifierIn amplifier design, everything starts with the power supply. The XPA-DR3 features a custom-configured version of our high-current switch mode power supply (SMPS) - a lightweight, powerful, intelligent design capable of delivering over 3 kW of continuous power with absolute reliability and extremely high efficiency. Our cutting edge SMPS offers the dynamic attributes of a classic transformer-based design with none of the drawbacks. Like the best transformer-based power supplies, our SMPS delivers plenty of continuous power to enable our amplifier modules to live up to their full performance potential, and plenty of dynamic power to ensure that musical peaks will never be compressed or limited. However, compared to transformer-based designs, our SMPS is lighter and more efficient; it’s also fully regulated, which ensures optimum performance under a wider range of load conditions. The Latest In A Long Line Of Great AmplifiersThe Differential Reference Amplifier Modules we use in our XPA-DR amplifiers use the same basic circuit topology as our legendary XPR series amplifiers. A unique differential input stage, with a cross-linked current source, drives a balanced voltage amplification stage, and this advanced input circuitry delivers an incredibly accurate and pure audio signal to the complementary, fully discrete output stage. A pair of these modules work together in perfect synergy to power a single channel of one of our new fully balanced, fully differential, XPA-DR amplifiers. Together they deliver a holistic, natural, and powerful listening experience. Low-level musical details and dialogue emerge from a deep black background; musical crescendos are delivered with both stunning impact and precision. The wide bandwidth, low distortion performance of the XPA-DR3 reveals every nuance of your high-resolution music sources, and it has plenty of power to drive even difficult loudspeakers with absolute authority and control.Class A/B Sound Quality Meets Optimized Class H EfficiencyThe Differential Reference™ Modules in the XPA-DR3 each use utilize a matched pair of amplifier modules, each of which features our fully analog Class A/B output stage, and our highly regarded Soft-Switch™ Class H power supply topology, which increases their efficiency significantly without compromising the audio performance you’d expect from an Emotiva amplifier. The output stage in each operates on a lower supply voltage at low power levels to minimize quiescent power consumption and standby power losses, instantly switching to a higher voltage rail when needed to ensure the signal passes cleanly and without clipping. This process happens on a continuous basis in real time, allowing greater overall efficiency, cooler operation, longer component life, reduced power consumption, and increased reliability.The Benefits Of A Fully Differential Balanced Power AmplifierMost experts agree that, if you want the absolute best sound quality and technical performance, you should use dedicated separate components. Because our power amplifiers are designed for a single purpose, we can concentrate on ensuring that they perform that one task very well, and avoid the compromises inherent in products that are expected to perform a variety of different functions.The Differential Reference Modules in the XPA-DR3 are each made up of a perfectly symmetrical balanced pair of high-performance amplifier modules. Each individual amplifier module already has vanishingly low distortion but, by connecting them as a balanced differential pair, a significant portion of the tiny amount of remaining nonlinearity is cancelled out. As a result, we are able to achieve even lower levels of distortion in the XPA-DR3, resulting in remarkably transparent sound, with unprecedented smoothness and clarity.When you put it all together, the XPA-DR3 is simply the finest three-channel amplifier we can devise, and we’re sure you’ll be as impressed with its performance as we are.Designed and Assembled in the USA with Globally Sourced ComponentsThe XPA-DR3 is designed, assembled, and tested in the USA, where we use the finest materials and latest technologies to bring you world-class products. Each Emotiva amplifier is carefully designed with premium components to deliver a stunningly capable, reliable, and refined system.LATEST AND GREATESTA new approach to amplifier design.When we set out to make the new X Series line, we analyzed everything in every amplifier we’ve ever made, from front to back, inside, and out. In doing so, we discovered several areas where our years of experience, and advances in audio technology, indicated that we could make significant improvements in our amplifier designs. After carefully weighing all the pros and cons, we kept the best features of our original designs, added a new set of optimizations and improvements, and the result became the foundation of our new line of audiophile amplifiers. The new XPA-DR amplifiers are the fully differential members of our new XPA amplifier family, and carry our philosophy of continuous product improvement to its ultimate conclusion.Modular ConstructionEach XPA-DR Differential Reference™ Power Amplifier is comprised of a heavy-duty chassis, which houses our massively overdesigned, fully regulated, 3 kW switch mode power supply, and up to three Differential Reference™ Amplifier Modules. The front panel display and protection system are designed to work with the maximum number of channels, and so need not be updated when the XPA-DR is expanded; on the rear panel, slots not occupied by amplifier modules will be covered with protective cover panels. (The XPA-DR3 is configured with a full complement of three Differential Reference Modules already installed.)Note: To ensure that amplifier channels are always installed properly, and function to our specifications, amplifier modules must be installed by Emotiva, or by your local authorized Emotiva service representative.

Up for Auction is an Emotiva XPA-DR3 Differential Reference Three-Channel Power Amplifier. This BEAST comes with plenty of power to run your front soundstage. See specs below. This was purchased new from Emotiva for a dedicated theater this past year but we are moving and will no longer be building a theater room. This also comes with the Emotiva Rack Ears as well. This amplifier is $2300 on Emotivas site so its a great opportunity to purchase new at a great discount. Please feel free to ask any questions and check out my other home theater listings with amplifiers from Emotiva, a Audioquest Power conditioner, an Anthem Processor, an Epson 5040 Projector, and a JVC NZ7 Laser Projector. EVERYTHING IS PRICED TO SELL, FEEL FREE TO SEND APPROPRIATE OFFERS TO END AUCTION EARLY. Thank you The XPA-DR3 is a high-powered three-channel audiophile power amplifier that combines the exceptional accuracy and finesse of a true balanced differential design with the power you need to deliver musical crescendos and movie special effects with stunning realism and impact. Whatever your listening preferences, the XPA-DR3 will give you the combination of detail and power than only a fully differential amplifier can provide.The XPA-DR3 features three of our Differential Reference™ Amplifier Modules, and is the ideal choice to power the critical front three channels of an absolutely awesome surround sound music or home theater system. The XPA-DR3 delivers 450 watts RMS into 8 Ohms, and 600 watts RMS into 4 Ohms, all three channels driven, with less than 0.1% THD.The Power Supply: The Foundation Of A Great AmplifierIn amplifier design, everything starts with the power supply. The XPA-DR3 features a custom-configured version of our high-current switch mode power supply (SMPS) - a lightweight, powerful, intelligent design capable of delivering over 3 kW of continuous power with absolute reliability and extremely high efficiency. Our cutting edge SMPS offers the dynamic attributes of a classic transformer-based design with none of the drawbacks. Like the best transformer-based power supplies, our SMPS delivers plenty of continuous power to enable our amplifier modules to live up to their full performance potential, and plenty of dynamic power to ensure that musical peaks will never be compressed or limited. However, compared to transformer-based designs, our SMPS is lighter and more efficient; it’s also fully regulated, which ensures optimum performance under a wider range of load conditions. The Latest In A Long Line Of Great AmplifiersThe Differential Reference Amplifier Modules we use in our XPA-DR amplifiers use the same basic circuit topology as our legendary XPR series amplifiers. A unique differential input stage, with a cross-linked current source, drives a balanced voltage amplification stage, and this advanced input circuitry delivers an incredibly accurate and pure audio signal to the complementary, fully discrete output stage. A pair of these modules work together in perfect synergy to power a single channel of one of our new fully balanced, fully differential, XPA-DR amplifiers. Together they deliver a holistic, natural, and powerful listening experience. Low-level musical details and dialogue emerge from a deep black background; musical crescendos are delivered with both stunning impact and precision. The wide bandwidth, low distortion performance of the XPA-DR3 reveals every nuance of your high-resolution music sources, and it has plenty of power to drive even difficult loudspeakers with absolute authority and control.Class A/B Sound Quality Meets Optimized Class H EfficiencyThe Differential Reference™ Modules in the XPA-DR3 each use utilize a matched pair of amplifier modules, each of which features our fully analog Class A/B output stage, and our highly regarded Soft-Switch™ Class H power supply topology, which increases their efficiency significantly without compromising the audio performance you’d expect from an Emotiva amplifier. The output stage in each operates on a lower supply voltage at low power levels to minimize quiescent power consumption and standby power losses, instantly switching to a higher voltage rail when needed to ensure the signal passes cleanly and without clipping. This process happens on a continuous basis in real time, allowing greater overall efficiency, cooler operation, longer component life, reduced power consumption, and increased reliability.The Benefits Of A Fully Differential Balanced Power AmplifierMost experts agree that, if you want the absolute best sound quality and technical performance, you should use dedicated separate components. Because our power amplifiers are designed for a single purpose, we can concentrate on ensuring that they perform that one task very well, and avoid the compromises inherent in products that are expected to perform a variety of different functions.The Differential Reference Modules in the XPA-DR3 are each made up of a perfectly symmetrical balanced pair of high-performance amplifier modules. Each individual amplifier module already has vanishingly low distortion but, by connecting them as a balanced differential pair, a significant portion of the tiny amount of remaining nonlinearity is cancelled out. As a result, we are able to achieve even lower levels of distortion in the XPA-DR3, resulting in remarkably transparent sound, with unprecedented smoothness and clarity.When you put it all together, the XPA-DR3 is simply the finest three-channel amplifier we can devise, and we’re sure you’ll be as impressed with its performance as we are.Designed and Assembled in the USA with Globally Sourced ComponentsThe XPA-DR3 is designed, assembled, and tested in the USA, where we use the finest materials and latest technologies to bring you world-class products. Each Emotiva amplifier is carefully designed with premium components to deliver a stunningly capable, reliable, and refined system.LATEST AND GREATESTA new approach to amplifier design.When we set out to make the new X Series line, we analyzed everything in every amplifier we’ve ever made, from front to back, inside, and out. In doing so, we discovered several areas where our years of experience, and advances in audio technology, indicated that we could make significant improvements in our amplifier designs. After carefully weighing all the pros and cons, we kept the best features of our original designs, added a new set of optimizations and improvements, and the result became the foundation of our new line of audiophile amplifiers. The new XPA-DR amplifiers are the fully differential members of our new XPA amplifier family, and carry our philosophy of continuous product improvement to its ultimate conclusion.Modular ConstructionEach XPA-DR Differential Reference™ Power Amplifier is comprised of a heavy-duty chassis, which houses our massively overdesigned, fully regulated, 3 kW switch mode power supply, and up to three Differential Reference™ Amplifier Modules. The front panel display and protection system are designed to work with the maximum number of channels, and so need not be updated when the XPA-DR is expanded; on the rear panel, slots not occupied by amplifier modules will be covered with protective cover panels. (The XPA-DR3 is configured with a full complement of three Differential Reference Modules already installed.)Note: To ensure that amplifier channels are always installed properly, and function to our specifications, amplifier modules must be installed by Emotiva, or by your local authorized Emotiva service representative.

Rane DR3 Master/Zone Remote Control (white). Used good working condition Remotely Controls Zone Source and Volume Can Be Configured as a Master Control LCD Displays Zone, Source, and Level Wall-Mounted 2-Gang Switchplate TheDR3 Master/Zone Remote ControlbyRaneis designed for use with their CP66, HAL1, and EXP1 multi-zone audio systems. It can be used as a zone-specific volume/source control with all three multi-zone systems. However, with the CP66, it can be used as a master remote The intuitive LCD display shows the current level and zone its connected to. The display has a backlight that turns on when used, then dims when not in use. The DR3 may be installed in a standard 2-gang electrical box with a minimum depth of 2.25 (5.7 cm). Connects by CAT 5e Ethernet cable up to 1,000 feet. Ships to Continental USA only

Emotiva - XPA-DR3 Differential Reference Three-Channel Power Amplifier. Power Output (all three channels driven): 450 watts RMS, per channel, into 8 Ohms, at <0.1% THD. 600 watts RMS, per channel, into 4 Ohms, at <0.1% THD. This is an awesome 3 channel amp. No home theater anymore so I have no need to keep. There are absolutely no scratches are scuffs on the amplifier. Mint condition but I do NOT have the original box anymore. Note: Local pick up only. Since I do not have the original box, I will not risk damage by shipping.

Ausführliche Beratung Schneller Versand nach Zahlungseingang Großes Sortiment zu super Preisen Navigation ? x Unser Shop Bewertungen Kontakt

Naim CD3 + Dual CS506 + Nakimichi DR3. Naim CD player and Dual CS506 turntable with Ortofon cartridge and Nakamichi DR3 cassette deck, as a job lot. All are in pristine condition, and fully working order (barely used).

Nakamichi DR1, DR2, DR3, DR8, DR10 2 Original Cassette Deck Feet Just the two DR feet, and these came from a DR-2, but are the same for ALL the DR range. You may just need the two, and these are in excellent condition.

Sie bieten auf ein Highend Kassettendeck von Nakamichi, das DR-3. Das Gerät ist voll funktionstüchtig und in einem absolut Top-Zustand. Lediglich auf der Oberfläche hat es von einem anderen Gerät leichte Gebrauchsspuren, siehe Fotos. Das Gerät ist eingepackt und leicht angestaubt. Ich wollte es für die Fotos jetzt nicht abstauben, da ich keine Kratzer o.ä. verursachen möchte. Die weißen Punkte auf den Fotos sind also nur Staub, keine Beschädigungen. Gerne können Sie mir einen Preisvorschlag unterbreiten. Technische Daten (nur der Vollständigkeit halber, potentielle Käufer kennen dieses Highend Tapedeck sicherlich): Hersteller: NakamichiModell: DR-3Baujahre: 1993 - 1995Hergestellt in: JapanFarbe: SchwarzFernbedienung: NeinLeistungsaufnahme: 20 WattAbmessungen: 430 x 100 x 320 mm (BxHxT)Gewicht: 5,4 kg AnschlüsseAnzahl der Eingänge:Line 50 mV/40 KOhmAnzahl der Ausgänge:Line 0,5 V/2,2 KOhmKopfhörer Technische DatenTonköpfe: 2Motoren: 3Gleichlaufschwankungen: 0,06% WRMSBandarten: I, II, IVFrequenzgang: 20 - 20.000 Hz (± 3 dB)Klirrfaktor: < 1%Signalrauschabstand: 64/70 dB (Dolby B/C)Auto-Reverse: NeinTitelsuchlauf: NeinDolby: B + CMPX-Filter: schaltbarFader: NeinPitch-Kontrolle: Nein Besondere Ausstattungen Bias-ReglerFluoreszenz-Pegelanzeige mit 2 x 13 Segmenten

Emotiva XPA - DR3 GEN 3 03/2028. the invoice will be attached to benefit from the guarantee with assignment letter slight scratch see photo, delivered with mains cable, trigger cable and manual shipping with insurance and double protective packaging

LEMEGA DR3 DAB/FM Portable Radio Bluetooth, Alarm & Clock Size: 17.7 x 10.7 x 5.5 cm - DAB/DAB+ and FM Digital Radio (store up to 40 pre-set stations)- Very good quality sound- Mains or battery powered (batteries not included)- USB lead- Dual alarm clock and snooze- Manual included- Please see photos for condition Bought two years ago on Amazon, wasnt used very often. Smoke and pet free home Will combine postage Also listing other items, please take a look. Happy bidding