No longer use the built in subwoofers so I don’t need the unit. Works great. 250 watts! Make an offer

Item is in working condition and includes power cord. Shipped carefully so no damage occurs. Please message if you have any questions! Buy from a trusted seller since 2017! Product Description Bowers & Wilkins SA250 Mk2 250W Rack-Mount Amplifier The Bowers & Wilkins SA250 Mk2 is designed to power and apply the correct equalization to the ISW-3 and ISW-4 custom install subwoofers. It is not suitable for driving any other loudspeakers. Specifications Description: 250W rack-mount amplifier with built-in sub-woofer equalization Amplifier inputs 2x RCA Phono socket, line in 2x RCA Phono socket, link out 1x XLR socket, line in 1x XLR socket, link out 3.5mm jack 12V trigger on/standby(overrides manual standby setting) 3.5mm jack 12V trigger equalization movie/music Amplifier outputs 1x Neutrik Speakon 4-pole speaker socket 2x pairs of Binding Posts Amplifier power output 250W Input impedance 33k? Signal / noise >80dB Rated power consumption 95W – 1/8 full power 30W – Idling Dimensions Height: 100mm (3.9 in) [88.5mm (3.5 in) plus feet] Width: 430mm (16.9 in) Depth: 322mm (12.7 in) Front panel Height: 2U 88.1mm/3.5 in Net weight 5.4kg (11.9 lb)

You are bidding on a Conrad Johnson Sonographe SA-250 power amplifier. Light wear as pictured. Works great. Comes with power cable. Ships FedEx Ground.

Product highlightsamplifier for Bowers & Wilkins ISW3 or ISW4 in-wall subwoofer Class D amplifier rated at 250 watts into 8 ohms or 4 ohms rack-mountable with included hardware front-panel volume, phase, low-pass crossover, bass extension, and EQ controls balanced mono XLR input and output unbalanced stereo line-level RCA inputs and outputs two sets of binding post speaker outputs one Neutrik Speakon speaker output signal-sensing auto on/off mode 3.5mm 12-volt trigger inputs for power-on and movie/music mode 16-15/16W x 3-15/16H x 14-3/16D (rack spaces: 2U) weight: 11.9 lbs. warranty: 2 years Whats in the boxCustom install subwoofer amplifier 59 AC power cord 3-Piece Neutrik Speakon plug 2 Rack-mount brackets 2 Handles 4 Long screws 6 Short screws 10 Flat washers 10 Lock washers 4 Rubber hole plugs Custom Installation booklet Safety and Warranty Instructions About this itemWritten by Crutchfields James Ralston

B&W SA250 MK2 amplifier. Condition is Used. Shipped with USPS Ground Advantage.

Product highlightsamplifier for Bowers & Wilkins ISW3 or ISW4 in-wall subwoofer Class D amplifier rated at 250 watts into 8 ohms or 4 ohms rack-mountable with included hardware front-panel volume, phase, low-pass crossover, bass extension, and EQ controls balanced mono XLR input and output unbalanced stereo line-level RCA inputs and outputs two sets of binding post speaker outputs one Neutrik Speakon speaker output signal-sensing auto on/off mode 3.5mm 12-volt trigger inputs for power-on and movie/music mode 16-15/16W x 3-15/16H x 14-3/16D (rack spaces: 2U) weight: 11.9 lbs. warranty: 2 years Whats in the boxCustom install subwoofer amplifier 59 AC power cord 3-Piece Neutrik Speakon plug 2 Rack-mount brackets 2 Handles 4 Long screws 6 Short screws 10 Flat washers 10 Lock washers 4 Rubber hole plugs Custom Installation booklet Safety and Warranty Instructions About this itemWritten by Crutchfields James Ralston

CONRAD-JOHNSON Sonographe SA250 High Current Amplifier. In good working condition. Missing one foot.Selling AS IS, As Pictured.Shipping is for the lower 48 states.

Bowers & Wilkins SA250 Mk2 250W Rack Mount Amplifier. (though it does have feet so could be stacked if required)This has been run for 20 minutes in its entire life so I could test it before putting on ebay, it is in perfect working order. I bought this for my new house but never fitted the in-wall subs so never used it. It’s in brand new condition.Please note this is a very high end and very specific amp, it’s only really suitable for subs. Here are the specs below. Description 250W rack-mount amplifier with built-in sub- woofer equalisation Amplifier inputs – 2x RCA Phono socket, line in – 2x RCA Phono socket, link out – 1x XLR socket, line in – 1x XLR socket, link out – 3.5mm jack – 12V trigger on/standby (overrides manual standby setting) – 3.5mm jack – 12V trigger equalisation movie/music Amplifier outputs – 1x Neutrik® Speakon® 4-pole speaker socket – 2x pairs of Binding Posts Amplifier power output 250W Input impedance 33k? Signal / noise >80dB Rated power consumption 95W – 1/8 full power 30W – Idling Dimensions Height: 100mm (3.9 in) [88.5mm (3.5 in) plus feet] Width: 430mm (16.9 in) Depth: 322mm (12.7 in) Front panel Height: 2U 88.1mm/3.5 in Net weight 5.4kg (11.9 lb)

Der Subwooferverstärker SA250 Mk2 ist speziell für die Einbausubwoofer ISW-3 und ISW-4 der Custom Installation-Serie entwickelt worden. Einen passenden ISW4 habe ich auch, wird gesondert inseriert!! Bei einer Höhe von 88,5 mm und einem Gewicht von 5,4 kg glänzt er mit einer Leistung von 250 Watt. Über einen speziellen Schalter kann das jeweilige Subwoofermodell (ISW-3 oder ISW-4) ausgewählt werden. Modell SA250 Mk2 Beschreibung 250-Watt-Subwooferverstärker für die Rackmontage Gerätefront: Drehschalter für die Lautstärke (Line in) Drehschalter für die Frequenz (Tiefpassfilter) (4. Ordnung Linkwitz, 40 Hz - 140 Hz) Schalter mit zwei Positionen (Tiefpassfilter) Phasenschalter 0º/180º (2 Positionen) Basserweiterung (Schalter mit 3 Rückseite: Schalter für die Modellauswahl (2 Positionen: ISW-3/ISW-4) Verstärkereingänge 2 x Cinch-Buchsen, Line in 2 x Cinch-Buchsen, Link out 1 x XLR-Buchse, Line in 1 x XLR-Buchse, Link out 3,5-mm-Anschluss - 12V-Trigger On/Standby (umgeht die manuelle Standby-Einstellung) 3,5-mm-Anschluss - 12V-Trigger EQ-Funktionen Movie/ Verstärkerausgänge 1 x vierpoliger Neutrik®-Speakon®-Anschluss 2 Paar Anschlussklemmen Ausgangsleistung des Verstärkers 250 W Der Verstärker ist nur wenig gelaufen und im Neuzustand, wurde eine Zeitlang als Ausstellungsstück genutzt, ist nie am Limit betrieben worden. Weitere Bowers Wilkins Produkte in anderen Anzeigen. ACHTUNG WICHTIGER HINWEIS!! Wegen der neuen Gesetzesbestimmungen erfolgt der Verkauf unter Ausschluss jeglicher Gewährleistung, Garantie und Rücknahme. Da es sich um einen Privatverkauf handelt, kann ich keine Garantie nach neuem EU-Recht übernehmen. Der Käufer erklärt sich damit einverstanden und erkennt dies mit seinem Kauf an!

TITLE WILL GO HERE Welcome to Laptop DFW Store Contact Us Feedback shop categories Motherboard Laptop Electronics Other Bowers & Wilkins SA250 Mk2 Black 33k Ohm 250W Power Output Rack Mount Amplifier description *** PLEASE CHECK THE LISTING DESCRIPTION CAREFULLY ***TESTED TO POWER ONLY NO OTHER TEST DONE.SPEAKER CONNECTOR BROKEN.Bowers & Wilkins SA250 Mk2 Black 33k Ohm 250W Power Output Rack Mount Amplifier. SPECSCONDITIONFor PartsBrandBowers & WilkinsModelBowers & Wilkins SA250 Mk2ColorBlack TypeAmplifierPower250W  The physical condition of our used equipment may have minor scratches, blemishes, or other deficiencies from regular use, Payment We accept Paypal Credit Cards, Debit Cards and Google pay. Shipping We will ship all orders within 3 business days of payment. We ship thru FEDEX or UPS. Return NO RETURNS ACCEPTED. Feedback Once you have received your item and are happy with your purchase please leave feedback. We will automatically leave good feedback for all purchases. Discount For Why Shop With LAPTOP DFW Experienced eBay seller that cares Specialist in Computer product & accessories Get the most out of Used items Superior customer service & Support Need Help? We are here for you 9:30am - 5pm Monday to Friday Great Customer Service Fast Shipping Quality Products RECEIVE OUR NEWSLETTER Store Contact Us Visit Feedback Copyright © 2022, LAPTOP DFW. All rights reserved. Listing and template services provided by inkFrog

Bowers & Wilkins SA250 Mk2 250W Rack Mount Amplifier. (though it does have feet so could be stacked if required)This has been run for 20 minutes in its entire life so I could test it before putting on ebay, it is in perfect working order. I bought this for my new house but never fitted the in-wall subs so never used it. It’s in brand new condition.Please note this is a very high end and very specific amp, it’s only really suitable for subs. Here are the specs below. Description 250W rack-mount amplifier with built-in sub- woofer equalisation Amplifier inputs – 2x RCA Phono socket, line in – 2x RCA Phono socket, link out – 1x XLR socket, line in – 1x XLR socket, link out – 3.5mm jack – 12V trigger on/standby (overrides manual standby setting) – 3.5mm jack – 12V trigger equalisation movie/music Amplifier outputs – 1x Neutrik® Speakon® 4-pole speaker socket – 2x pairs of Binding Posts Amplifier power output 250W Input impedance 33k? Signal / noise >80dB Rated power consumption 95W – 1/8 full power 30W – Idling Dimensions Height: 100mm (3.9 in) [88.5mm (3.5 in) plus feet] Width: 430mm (16.9 in) Depth: 322mm (12.7 in) Front panel Height: 2U 88.1mm/3.5 in Net weight 5.4kg (11.9 lb)

In good working condition. Power cord not original and was upgraded by previous owner. Clean condition but shows marks of ages. Sold AS- IS. 110 volts /60 Hz USA/Canada standard. Thanks for watching.

Bowers & Wilkins SA250 Mk2 250W Rack Mount Amplifier. (though it does have feet so could be stacked if required)This has been run for 20 minutes in its entire life so I could test it before putting on ebay, it is in perfect working order. I bought this for my new house but never fitted the in-wall subs so never used it. It’s in brand new condition.Please note this is a very high end and very specific amp, it’s only really suitable for subs. Here are the specs below. Description 250W rack-mount amplifier with built-in sub- woofer equalisation Amplifier inputs – 2x RCA Phono socket, line in – 2x RCA Phono socket, link out – 1x XLR socket, line in – 1x XLR socket, link out – 3.5mm jack – 12V trigger on/standby (overrides manual standby setting) – 3.5mm jack – 12V trigger equalisation movie/music Amplifier outputs – 1x Neutrik® Speakon® 4-pole speaker socket – 2x pairs of Binding Posts Amplifier power output 250W Input impedance 33k? Signal / noise >80dB Rated power consumption 95W – 1/8 full power 30W – Idling Dimensions Height: 100mm (3.9 in) [88.5mm (3.5 in) plus feet] Width: 430mm (16.9 in) Depth: 322mm (12.7 in) Front panel Height: 2U 88.1mm/3.5 in Net weight 5.4kg (11.9 lb)

In good working condition. Power cord not original and was upgraded by previous owner. Clean condition but shows marks of ages. Sold AS- IS. 110 volts /60 Hz USA/Canada standard. Thanks for watching.