2 x JAN-CRC-6V6 RCA Tubes Made in USA VT-107 = Military Specs Metal Tubes Matched by mA ***They may have some rust - see pictures*** The auction is for 2 Tubes Tested on enhanced Triplet E3444 Laboratory tester by Paul Hart of Ga. Results =4700 micromhos @ 48 mA 4500 micromhos @ 48 mA Bogey(100% or ew) = 4100 @ 45 mA +/- 10% The measurements in this listing were taken on a Triplett 3444 modified to test the tube as an amplifier in accordance with RMA/EIA specifications, utilized by all US and most foreign tube manufacturers. This tester applies test conditions for this tube as shown below (including the precise filament voltage) and then measures transconductance (gm) in accordance with the engineering definition of gm. Tubes may also be operated under the test conditions for extended periods to be sure that it is stable. A tube must be tested in this manner to compare its test results with the manufacturer’s original intent or with other tubes of the same type. Most tube testers do not apply the test conditions required or conduct a valid gm test. For more details on the test and our test equipment, please contact us.The test conditions for this listing are__250_Volts plate, __250_Volts screen, ___-12.5___Volts bias or Cathode resistance*What were your tubes tested at? I do combine S&H

2 x JAN-CKR-6V6 Ken-Rad Tubes Made in USA VT-107 = Military Specs Metal Tubes Matched by mA ***They may have some rust - see pictures*** The auction is for 2 Tubes Tested on enhanced Triplet E3444 Laboratory tester by Paul Hart of Ga. Results =4500 micromhos @ 41 mA 4400 micromhos @ 40 mA Bogey(100% or ew) = 4100 @ 45 mA +/- 10% The measurements in this listing were taken on a Triplett 3444 modified to test the tube as an amplifier in accordance with RMA/EIA specifications, utilized by all US and most foreign tube manufacturers. This tester applies test conditions for this tube as shown below (including the precise filament voltage) and then measures transconductance (gm) in accordance with the engineering definition of gm. Tubes may also be operated under the test conditions for extended periods to be sure that it is stable. A tube must be tested in this manner to compare its test results with the manufacturer’s original intent or with other tubes of the same type. Most tube testers do not apply the test conditions required or conduct a valid gm test. For more details on the test and our test equipment, please contact us.The test conditions for this listing are__250_Volts plate, __250_Volts screen, ___-12.5___Volts bias or Cathode resistance*What were your tubes tested at? I do combine S&H

This Accuphase T 107 FM tuner is a high-quality, digital tuner from Japan. It is designed for use in the US and features Stereo L/R RCA audio outputs. The tuner supports FM mode only (no AM) and has a black color finish. It is a great addition to any home audio system, and with its Accuphase brand, users can be assured of its quality and durability. The Accuphase T 107 tuner is a highly sought-after item for audiophiles and collectors alike, and this US model is sure to impress. This is the model made for use in the USA, so it does tune stations in the USA correctly and has the full range of stations. Comes with a reprinted manual as shown. Technically, this is the T-107B model because it is black in color. There are rubs and scratches on the top that are difficult to photograph. Some of the scratches have been marked over, but you can tell they are there. The narrow/normal switch has some discoloration. Although it does have these blemishes, it still looks quite nice overall. This unit is working as intended with no issues. I will include the antenna adapter for use with typical antennas. Please note that shipping costs are high because this will be well packed and secure. It will require a large box for adequate padding. It will be insured for the sale value. Shipping in continental USA only Shipping will vary by locationOn Sep-15-23 at 18:02:53 PDT, seller added the following information: New pictrures have been added.On Sep-16-23 at 17:18:15 PDT, seller added the following information: The meter works fine on this unit, it was set on the multipath settting in the photos. In multipath setting, being all the way to the left that indicates the signal is clear of multipath interference. When set to strength mode, it does move and show the signal strength as intended. All functions of this tuner are working correctly.

2 Vintage Tested RCA 6V6 Vacuum tubes! Please see the detailed pictures below Please see shipping calculator for shipping costs, Item is located in Vancovuer BC and can be shipped with the USPS out of Washington state or Canada Post for Canadian buyers. items over $120 will not be shipped without tracking which can be pricey to some overseas locations. Please see below for details on shipping. 2 Vintage RCA USA 6V6 VT-107 Vacuum tubes. Tubes have been tested on a Calibrated Hickok TV7 tube tester and test as follows:Tube1 : 88 Tube2 : 84 Minimun good value on a TV7 tester for a 6V6gt tube is 46. The tubes test very well. Tubes are guaranteed to be in good working order upon delivery. If a tube ends up bad within 1 week of delivery just ship it back for a full refund on the bad tube minus shipping costs. See pictures for details. If you have any questions please email. I will ship worldwide.Buyer to pay all shipping costs including brokerage and taxes if any. Item is located in Canada but will be shipped with the USPS for USA buyers or Canada Post for Canadian buyers. For overseas buyers : Please email for options as sometimes Canada post is cheaper for overseas shipping with Surface post. Please wait for my invoice before paying to avoid any hassles. I do combine shipping to save you costs! See my other auctions for more vintage audio gear! Local pickup in Vancouver BC is also available. GOOD LUCK!!!!!!!

When ordering from the US, parcels may be subject to import tax and duty charges, which the buyer is responsible to pay.2 x JAN-CRC-6V6 RCA Metal Tubes Super Strong Matched Pair Mil Spec=VT-107 #1This product data sheet is originally written in English.2 x JAN-CRC-6V6 RCA TubesMade in USAVT-107 = Military Specs Metal TubesMatched by mA***They may have some rust - see pictures***The auction is for 2 Tubes Tested on enhanced Triplet E3444 Laboratory tester by Paul Hart of Ga.Results =4700 micromhos @ 48 mA4500 micromhos @ 48 mABogey(100% or ew) = 4100 @ 45 mA +/- 10%The measurements in this listing were taken on a Triplett 3444 modified to test the tube as an amplifier in accordance with RMA/EIA specifications, utilized by all US and most foreign tube manufacturers. This tester applies test conditions for this tube as shown below (including the precise filament voltage) and then measures transconductance (gm) in accordance with the engineering definition of gm. Tubes may also be operated under the test conditions for extended periods to be sure that it is stable. A tube must be tested in this manner to compare its test results with the manufacturer’s original intent or with other tubes of the same type. Most tube testers do not apply the test conditions required or conduct a valid gm test. For more details on the test and our test equipment, please contact us.The test conditions for this listing are__250_Volts plate, __250_Volts screen, ___-12.5___Volts bias or Cathode resistance*What were your tubes tested at?I do combine S&HThe measurements in this listing were taken on a Triplett 3444 modified to test the tube as an amplifier in accordance with RMA/EIA specifications, utilized by all US and most foreign tube manufacturers. This tester applies test conditions for this tube as shown below (including the precise filament voltage) and then measures transconductance (gm) in accordance with the engineering definition of gm. Tubes may also be operated under the test conditions for extended periods to be sure that it is stable. A tube must be tested in this manner to compare its test results with the manufacturer’s original intent or with other tubes of the same type. Most tube testers do not apply the test conditions required or conduct a valid gm test. For more details on the test and our test equipment, please co Brand RCA Model 6v6

When ordering from the US, parcels may be subject to import tax and duty charges, which the buyer is responsible to pay.2 x JAN-CRC-6V6 RCA Metal Tubes Super Strong Matched Pair Mil Spec=VT-107 #1This product data sheet is originally written in English.2 x JAN-CRC-6V6 RCA TubesMade in USAVT-107 = Military Specs Metal TubesMatched by mA***They may have some rust - see pictures***The auction is for 2 Tubes Tested on enhanced Triplet E3444 Laboratory tester by Paul Hart of Ga.Results =4700 micromhos @ 48 mA4500 micromhos @ 48 mABogey(100% or ew) = 4100 @ 45 mA +/- 10%The measurements in this listing were taken on a Triplett 3444 modified to test the tube as an amplifier in accordance with RMA/EIA specifications, utilized by all US and most foreign tube manufacturers. This tester applies test conditions for this tube as shown below (including the precise filament voltage) and then measures transconductance (gm) in accordance with the engineering definition of gm. Tubes may also be operated under the test conditions for extended periods to be sure that it is stable. A tube must be tested in this manner to compare its test results with the manufacturer’s original intent or with other tubes of the same type. Most tube testers do not apply the test conditions required or conduct a valid gm test. For more details on the test and our test equipment, please contact us.The test conditions for this listing are__250_Volts plate, __250_Volts screen, ___-12.5___Volts bias or Cathode resistance*What were your tubes tested at?I do combine S&HThe measurements in this listing were taken on a Triplett 3444 modified to test the tube as an amplifier in accordance with RMA/EIA specifications, utilized by all US and most foreign tube manufacturers. This tester applies test conditions for this tube as shown below (including the precise filament voltage) and then measures transconductance (gm) in accordance with the engineering definition of gm. Tubes may also be operated under the test conditions for extended periods to be sure that it is stable. A tube must be tested in this manner to compare its test results with the manufacturer’s original intent or with other tubes of the same type. Most tube testers do not apply the test conditions required or conduct a valid gm test. For more details on the test and our test equipment, please co Brand RCA Model 6v6

2 x JAN-CRC-6V6 RCA TubesMade in USAVT-107 = Military Specs Metal TubesMatched by mA***They may have some rust - see pictures***The auction is for 2 Tubes Tested on enhanced Triplet E3444 Laboratory tester by Paul Hart of Ga.Results =4700 micromhos @ 48 mA4500 micromhos @ 48 mABogey(100% or ew) = 4100 @ 45 mA +/- 10%The measurements in this listing were taken on a Triplett 3444 modified to test the tube as an amplifier in accordance with RMA/EIA specifications, utilized by all US and most foreign tube manufacturers. This tester applies test conditions for this tube as shown below (including the precise filament voltage) and then measures transconductance (gm) in accordance with the engineering definition of gm. Tubes may also be operated under the test conditions for extended periods to be sure that it is stable. A tube must be tested in this manner to compare its test results with the manufacturer’s original intent or with other tubes of the same type. Most tube testers do not apply the test conditions required or conduct a valid gm test. For more details on the test and our test equipment, please contact us.The test conditions for this listing are__250_Volts plate, __250_Volts screen, ___-12.5___Volts bias or Cathode resistance*What were your tubes tested at?I do combine S&HThe measurements in this listing were taken on a Triplett 3444 modified to test the tube as an amplifier in accordance with RMA/EIA specifications, utilized by all US and most foreign tube manufacturers. This tester applies test conditions for this tube as shown below (including the precise filament voltage) and then measures transconductance (gm) in accordance with the engineering definition of gm. Tubes may also be operated under the test conditions for extended periods to be sure that it is stable. A tube must be tested in this manner to compare its test results with the manufacturer’s original intent or with other tubes of the same type. Most tube testers do not apply the test conditions required or conduct a valid gm test. For more details on the test and our test equipment, please co

2 x JAN-CRC-6V6 RCA TubesMade in USAVT-107 = Military Specs Metal TubesMatched by mA***They may have some rust - see pictures***The auction is for 2 Tubes Tested on enhanced Triplet E3444 Laboratory tester by Paul Hart of Ga.Results =4700 micromhos @ 48 mA4500 micromhos @ 48 mABogey(100% or ew) = 4100 @ 45 mA +/- 10%The measurements in this listing were taken on a Triplett 3444 modified to test the tube as an amplifier in accordance with RMA/EIA specifications, utilized by all US and most foreign tube manufacturers. This tester applies test conditions for this tube as shown below (including the precise filament voltage) and then measures transconductance (gm) in accordance with the engineering definition of gm. Tubes may also be operated under the test conditions for extended periods to be sure that it is stable. A tube must be tested in this manner to compare its test results with the manufacturer’s original intent or with other tubes of the same type. Most tube testers do not apply the test conditions required or conduct a valid gm test. For more details on the test and our test equipment, please contact us.The test conditions for this listing are__250_Volts plate, __250_Volts screen, ___-12.5___Volts bias or Cathode resistance*What were your tubes tested at?I do combine S&HThe measurements in this listing were taken on a Triplett 3444 modified to test the tube as an amplifier in accordance with RMA/EIA specifications, utilized by all US and most foreign tube manufacturers. This tester applies test conditions for this tube as shown below (including the precise filament voltage) and then measures transconductance (gm) in accordance with the engineering definition of gm. Tubes may also be operated under the test conditions for extended periods to be sure that it is stable. A tube must be tested in this manner to compare its test results with the manufacturer’s original intent or with other tubes of the same type. Most tube testers do not apply the test conditions required or conduct a valid gm test. For more details on the test and our test equipment, please co

Les commandes réalisées à partir des États-Unis, peuvent être soumises à des taxes dimportation et droits de douane, que lacheteur est tenu responsable de payer.2 X JAN-CRC-6V6 RCA Métal Tubes Super Fort Paire Assortie Mil Spec = VT-107 #1Cette fiche produit est originalement écrite en anglais. Veuillez trouver ci dessous une traduction automatique en français. Si vous avez des questions veuillez nous contacter.2 tubes RCA JAN-CRC-6V6Fabriqué aux États-UnisVT-107 = Spécifications militaires Tubes métalliquesApparié par mA***Ils peuvent avoir un peu de rouille - voir photos***Lenchère est pour 2 Tubes Testé sur le testeur de laboratoire Triplet E3444 amélioré par Paul Hart of Ga.Résultats =4700 micromhos à 48 mA4500 micromhos @ 48 mABogey (100 % ou petit) = 4100 @ 45mA +/- 10%Les mesures de cette liste ont été prises sur un Triplett 3444 modifié pour tester le tube en tant quamplificateur conformément aux spécifications RMA/EIA, utilisées par tous les fabricants de tubes américains et la plupart des fabricants étrangers. Ce testeur applique les conditions de test pour ce tube comme indiqué ci-dessous (y compris la tension précise du filament), puis mesure la transconductance (gm) conformément à la définition technique de gm. Les tubes peuvent également être utilisés dans les conditions dessai pendant de longues périodes pour sassurer quils sont stables. Un tube doit être testé de cette manière pour comparer ses résultats de test avec lintention initiale du fabricant ou avec dautres tubes du même type. La plupart des testeurs de tubes nappliquent pas les conditions de test requises ou neffectuent pas de test gm valide. Pour plus de détails sur le test et notre équipement de test, veuillez nous contacter.Les conditions de test pour cette liste sont__250_Plaque Volts, __250_Écran Volts, ___-12.5___ Polarisation des volts ou résistance de la cathode*À quoi vos tubes ont-ils été testés ?Je combine S&HLes mesures de cette liste ont été prises sur un Triplett 3444 modifié pour tester le tube en tant quamplificateur conformément aux spécifications RMA/EIA, utilisées par tous les fabricants de tubes américains et la plupart des fabricants étrangers. Ce testeur applique les conditions de test pour ce tube comme indiqué ci-dessous (y compris la tension précise du filament), puis mesure la transconductance (gm) conformément à la définition technique de gm. Les tubes peuvent également être utilisés dans les conditions dessai pendant de longues périodes pour sassurer quils sont stables. Un tube doit être testé de cette manière pour comparer ses résultats de test avec lintention initiale du fabricant ou avec dautres tubes du même type. La plupart des testeurs de tubes nappliquent pas les Brand RCA Model 6v6

Les commandes réalisées à partir des États-Unis, peuvent être soumises à des taxes dimportation et droits de douane, que lacheteur est tenu responsable de payer.2 X JAN-CKR-6V6 KEN-RAD Métal Tubes Très Fort Paire Assortie VT-107 #1Cette fiche produit est originalement écrite en anglais. Veuillez trouver ci dessous une traduction automatique en français. Si vous avez des questions veuillez nous contacter.2 tubes Ken-Rad JAN-CKR-6V6Fabriqué aux États-UnisVT-107 = Spécifications militaires Tubes métalliquesApparié par mA***Ils peuvent avoir un peu de rouille - voir photos***Lenchère est pour 2 Tubes Testé sur le testeur de laboratoire Triplet E3444 amélioré par Paul Hart of Ga.Résultats =4500 micromhos à 41 mA4400 micromhos à 40 mABogey (100 % ou petit) = 4100 @ 45mA +/- 10%Les mesures de cette liste ont été prises sur un Triplett 3444 modifié pour tester le tube en tant quamplificateur conformément aux spécifications RMA/EIA, utilisées par tous les fabricants de tubes américains et la plupart des fabricants étrangers. Ce testeur applique les conditions de test pour ce tube comme indiqué ci-dessous (y compris la tension précise du filament), puis mesure la transconductance (gm) conformément à la définition technique de gm. Les tubes peuvent également être utilisés dans les conditions dessai pendant de longues périodes pour sassurer quils sont stables. Un tube doit être testé de cette manière pour comparer ses résultats de test avec lintention initiale du fabricant ou avec dautres tubes du même type. La plupart des testeurs de tubes nappliquent pas les conditions de test requises ou neffectuent pas de test gm valide. Pour plus de détails sur le test et notre équipement de test, veuillez nous contacter.Les conditions de test pour cette liste sont__250_Plaque Volts, __250_Écran Volts, ___-12.5___ Polarisation des volts ou résistance de la cathode*À quoi vos tubes ont-ils été testés ?Je combine S&HLes mesures de cette liste ont été prises sur un Triplett 3444 modifié pour tester le tube en tant quamplificateur conformément aux spécifications RMA/EIA, utilisées par tous les fabricants de tubes américains et la plupart des fabricants étrangers. Ce testeur applique les conditions de test pour ce tube comme indiqué ci-dessous (y compris la tension précise du filament), puis mesure la transconductance (gm) conformément à la définition technique de gm. Les tubes peuvent également être utilisés dans les conditions dessai pendant de longues périodes pour sassurer quils sont stables. Un tube doit être testé de cette manière pour comparer ses résultats de test avec lintention initiale du fabricant ou avec dautres tubes du même type. La plupart des testeurs de tubes nappliquent pas les Brand KEN-RAD Model 6v6

2 x JAN-CKR-6V6 Ken-Rad TubesMade in USAVT-107 = Military Specs Metal TubesMatched by mA***They may have some rust - see pictures***The auction is for 2 Tubes Tested on enhanced Triplet E3444 Laboratory tester by Paul Hart of Ga.Results =4500 micromhos @ 41 mA4400 micromhos @ 40 mABogey(100% or ew) = 4100 @ 45 mA +/- 10%The measurements in this listing were taken on a Triplett 3444 modified to test the tube as an amplifier in accordance with RMA/EIA specifications, utilized by all US and most foreign tube manufacturers. This tester applies test conditions for this tube as shown below (including the precise filament voltage) and then measures transconductance (gm) in accordance with the engineering definition of gm. Tubes may also be operated under the test conditions for extended periods to be sure that it is stable. A tube must be tested in this manner to compare its test results with the manufacturer’s original intent or with other tubes of the same type. Most tube testers do not apply the test conditions required or conduct a valid gm test. For more details on the test and our test equipment, please contact us.The test conditions for this listing are__250_Volts plate, __250_Volts screen, ___-12.5___Volts bias or Cathode resistance*What were your tubes tested at?I do combine S&HThe measurements in this listing were taken on a Triplett 3444 modified to test the tube as an amplifier in accordance with RMA/EIA specifications, utilized by all US and most foreign tube manufacturers. This tester applies test conditions for this tube as shown below (including the precise filament voltage) and then measures transconductance (gm) in accordance with the engineering definition of gm. Tubes may also be operated under the test conditions for extended periods to be sure that it is stable. A tube must be tested in this manner to compare its test results with the manufacturer’s original intent or with other tubes of the same type. Most tube testers do not apply the test conditions required or conduct a valid gm test. For more details on the test and our test equipment, please co

When ordering from the US, parcels may be subject to import tax and duty charges, which the buyer is responsible to pay.2 x JAN-CKR-6V6 Ken-Rad Metal Tubes Very Strong Matched Pair VT-107 #1This product data sheet is originally written in English.2 x JAN-CKR-6V6 Ken-Rad TubesMade in USAVT-107 = Military Specs Metal TubesMatched by mA***They may have some rust - see pictures***The auction is for 2 Tubes Tested on enhanced Triplet E3444 Laboratory tester by Paul Hart of Ga.Results =4500 micromhos @ 41 mA4400 micromhos @ 40 mABogey(100% or ew) = 4100 @ 45 mA +/- 10%The measurements in this listing were taken on a Triplett 3444 modified to test the tube as an amplifier in accordance with RMA/EIA specifications, utilized by all US and most foreign tube manufacturers. This tester applies test conditions for this tube as shown below (including the precise filament voltage) and then measures transconductance (gm) in accordance with the engineering definition of gm. Tubes may also be operated under the test conditions for extended periods to be sure that it is stable. A tube must be tested in this manner to compare its test results with the manufacturer’s original intent or with other tubes of the same type. Most tube testers do not apply the test conditions required or conduct a valid gm test. For more details on the test and our test equipment, please contact us.The test conditions for this listing are__250_Volts plate, __250_Volts screen, ___-12.5___Volts bias or Cathode resistance*What were your tubes tested at?I do combine S&HThe measurements in this listing were taken on a Triplett 3444 modified to test the tube as an amplifier in accordance with RMA/EIA specifications, utilized by all US and most foreign tube manufacturers. This tester applies test conditions for this tube as shown below (including the precise filament voltage) and then measures transconductance (gm) in accordance with the engineering definition of gm. Tubes may also be operated under the test conditions for extended periods to be sure that it is stable. A tube must be tested in this manner to compare its test results with the manufacturer’s original intent or with other tubes of the same type. Most tube testers do not apply the test conditions required or conduct a valid gm test. For more details on the test and our test equipment, please co Brand KEN-RAD Model 6v6

2 x JAN-CKR-6V6 Ken-Rad TubesMade in USAVT-107 = Military Specs Metal TubesMatched by mA***They may have some rust - see pictures***The auction is for 2 Tubes Tested on enhanced Triplet E3444 Laboratory tester by Paul Hart of Ga.Results =4500 micromhos @ 41 mA4400 micromhos @ 40 mABogey(100% or ew) = 4100 @ 45 mA +/- 10%The measurements in this listing were taken on a Triplett 3444 modified to test the tube as an amplifier in accordance with RMA/EIA specifications, utilized by all US and most foreign tube manufacturers. This tester applies test conditions for this tube as shown below (including the precise filament voltage) and then measures transconductance (gm) in accordance with the engineering definition of gm. Tubes may also be operated under the test conditions for extended periods to be sure that it is stable. A tube must be tested in this manner to compare its test results with the manufacturer’s original intent or with other tubes of the same type. Most tube testers do not apply the test conditions required or conduct a valid gm test. For more details on the test and our test equipment, please contact us.The test conditions for this listing are__250_Volts plate, __250_Volts screen, ___-12.5___Volts bias or Cathode resistance*What were your tubes tested at?I do combine S&HThe measurements in this listing were taken on a Triplett 3444 modified to test the tube as an amplifier in accordance with RMA/EIA specifications, utilized by all US and most foreign tube manufacturers. This tester applies test conditions for this tube as shown below (including the precise filament voltage) and then measures transconductance (gm) in accordance with the engineering definition of gm. Tubes may also be operated under the test conditions for extended periods to be sure that it is stable. A tube must be tested in this manner to compare its test results with the manufacturer’s original intent or with other tubes of the same type. Most tube testers do not apply the test conditions required or conduct a valid gm test. For more details on the test and our test equipment, please co

When ordering from the US, parcels may be subject to import tax and duty charges, which the buyer is responsible to pay.2 x JAN-CKR-6V6 Ken-Rad Metal Tubes Very Strong Matched Pair VT-107 #1This product data sheet is originally written in English.2 x JAN-CKR-6V6 Ken-Rad TubesMade in USAVT-107 = Military Specs Metal TubesMatched by mA***They may have some rust - see pictures***The auction is for 2 Tubes Tested on enhanced Triplet E3444 Laboratory tester by Paul Hart of Ga.Results =4500 micromhos @ 41 mA4400 micromhos @ 40 mABogey(100% or ew) = 4100 @ 45 mA +/- 10%The measurements in this listing were taken on a Triplett 3444 modified to test the tube as an amplifier in accordance with RMA/EIA specifications, utilized by all US and most foreign tube manufacturers. This tester applies test conditions for this tube as shown below (including the precise filament voltage) and then measures transconductance (gm) in accordance with the engineering definition of gm. Tubes may also be operated under the test conditions for extended periods to be sure that it is stable. A tube must be tested in this manner to compare its test results with the manufacturer’s original intent or with other tubes of the same type. Most tube testers do not apply the test conditions required or conduct a valid gm test. For more details on the test and our test equipment, please contact us.The test conditions for this listing are__250_Volts plate, __250_Volts screen, ___-12.5___Volts bias or Cathode resistance*What were your tubes tested at?I do combine S&HThe measurements in this listing were taken on a Triplett 3444 modified to test the tube as an amplifier in accordance with RMA/EIA specifications, utilized by all US and most foreign tube manufacturers. This tester applies test conditions for this tube as shown below (including the precise filament voltage) and then measures transconductance (gm) in accordance with the engineering definition of gm. Tubes may also be operated under the test conditions for extended periods to be sure that it is stable. A tube must be tested in this manner to compare its test results with the manufacturer’s original intent or with other tubes of the same type. Most tube testers do not apply the test conditions required or conduct a valid gm test. For more details on the test and our test equipment, please co Brand KEN-RAD Model 6v6

ONE SYLVANIA JAN 6V6 OR VT-107-B COKE BOTTLE SHAPE vacuum tube TESTED ON MY HICKOK 539C TUBE TESTER MIN 2600 TEST RESULTS5000 AT 22 MA used. as is

2 Vintage Tested RCA 6V6 Vacuum tubes! Please see the detailed pictures below Please see shipping calculator for shipping costs, Item is located in Vancovuer BC and can be shipped with the USPS out of Washington state or Canada Post for Canadian buyers. items over $120 will not be shipped without tracking which can be pricey to some overseas locations. Please see below for details on shipping. 2 Vintage RCA USA 6V6 VT-107 Vacuum tubes. Tubes have been tested on a Calibrated Hickok TV7 tube tester and test as follows:Tube1 : 88 Tube2 : 84 Minimun good value on a TV7 tester for a 6V6gt tube is 46. The tubes test very well. Tubes are guaranteed to be in good working order upon delivery. If a tube ends up bad within 1 week of delivery just ship it back for a full refund on the bad tube minus shipping costs. See pictures for details. If you have any questions please email. I will ship worldwide.Buyer to pay all shipping costs including brokerage and taxes if any. Item is located in Canada but will be shipped with the USPS for USA buyers or Canada Post for Canadian buyers. For overseas buyers : Please email for options as sometimes Canada post is cheaper for overseas shipping with Surface post. Please wait for my invoice before paying to avoid any hassles. I do combine shipping to save you costs! See my other auctions for more vintage audio gear! Local pickup in Vancouver BC is also available. GOOD LUCK!!!!!!!

***PLEASE READ THE ENTIRE DESCRIPTION & REVIEW ALL PICTURES THESE TUBES ARE USED BUT STILL BELIEVED TO BE WITHIN FACTORY SPECS. THEY HAVE BEEN ASSESSED WITH THE ONLY RESOURCE WE HAVE - A LARGE VINTAGE MERCURY METER. *** HERE ARE SEVEN (7) MILITARY GRADE VINTAGE 40s-50s USA Sylvania JAN CHS 6V6-GT VT-107-A Tube SOLD INDIVIDUALLY. ALL TUBES HAVE THE SC 966A stamp, several have 4G and 55 stamping. One tube has tape residue on it that has been shown in 2 pictures. Several also have what appears to be some sort of thin scratch in the gray tint on the inside - we assume this to be a cosmetic rather than functional issue as they perform within the same specs (last picture shows the largest scratch). ALL TEST at 95 or above on our Mercury Meter

1940s Raytheon JAN-CRP-6V6GT/G VT-107-A Smoked Glass Tube - TV7 tested Horseshoe top, military spec.

2 RCA JAN-CRC-6V6GT 6V6GT/G VT-107-A tubes. Smoked. AT1000 100% 98% gm Testing Notes:Heaters were on for at least 2 minutes before testingPlate voltage is applied for at least 1 minute before testing.Tubes were checked for noise and microphonics One of the well known attributes of the Amplitrex is the sensitivity it has for gas testing. It is likely other tube testers will show no gas at all for these tubes. Amplitrex AT1000 results. New tube spec mhos is 4100 at 250V on the plate. Gas should be less than 4.5ma.Tube Codemhos Emissions %GM % H-K uAGas mAVIE44001081000.8V3E4030849801.4 Acceptable practice with power tubes is to have the gas below 10% of plate current (45ma), which is 4.5ma. So these tubes are well within the good range. It is likely other tube testers will show no gas at all. Cleaning the tubes is being left to the buyer since often cleaning the tubes also removes labeling.Test results are written on the tubes. These can be easily removed with a moist paper towel. Domestic purchases can be combined to reduce shipping costs. Items usually ship the day after payment is received.

Biete 2x 6V6 GT = VT-107-A Röhren von National Made in USA Die Röhren sind gebraucht und gepürft auf dem Funke W19 Röhrenprüfgerät (Der Gutbereich beginnt bei 18 mA) 1. Röhre 35 mA 2. Röhre 37 mA Der Versand kann weltweit erfolgen.

2 Vintage Tested RCA 6V6 Vacuum tubes! Please see the detailed pictures below Please see shipping calculator for shipping costs, Item is located in Vancovuer BC and can be shipped with the USPS out of Washington state or Canada Post for Canadian buyers. items over $120 will not be shipped without tracking which can be pricey to some overseas locations. Please see below for details on shipping. 2 Vintage RCA USA 6V6 VT-107 Vacuum tubes. Tubes have been tested on a Calibrated Hickok TV7 tube tester and test as follows:Tube1 : 88 Tube2 : 84 Minimun good value on a TV7 tester for a 6V6gt tube is 46. The tubes test very well. Tubes are guaranteed to be in good working order upon delivery. If a tube ends up bad within 1 week of delivery just ship it back for a full refund on the bad tube minus shipping costs. See pictures for details. If you have any questions please email. I will ship worldwide.Buyer to pay all shipping costs including brokerage and taxes if any. Item is located in Canada but will be shipped with the USPS for USA buyers or Canada Post for Canadian buyers. For overseas buyers : Please email for options as sometimes Canada post is cheaper for overseas shipping with Surface post. Please wait for my invoice before paying to avoid any hassles. I do combine shipping to save you costs! See my other auctions for more vintage audio gear! Local pickup in Vancouver BC is also available. GOOD LUCK!!!!!!!

2 x Tubes Ken-Rad 6V6GT/G ( VT-107-A ) with good Values. The items are shipped with German Post. 472Z

Kramer KT-107 Overview The Touch Panel for Wall Mount and Table Mount with PoE from Kramer is a 7 IPS multi-touch panel with 1280 x 800 resolution. Designed for decorative room integration, this portable touch panel can be deployed either tabletop or on-wall, mounted inside standard in-wall junction boxes. The touch panel supports Power over Ethernet (PoE) and advanced Wi-Fi connectivity options and is an Android-based touch panel that is ideal for any 24/7 Kramer-supported commercial AV or control application and features a user-friendly, fully customizable graphical user interface configured by Kramer software.7 IPS, portable, and multi-touch panelSupports wired PoE and advanced Wi-Fi connectivity options1280 x 800 resolution±85° horizontal and vertical viewing anglesAdvanced ten multi-touch points and two-finger gesture capabilitiesBuilt-in lighting sensor for auto-adaptable brightnessSingle RJ45 Ethernet cable for connectivity and poweringSeamless switching between wired and wireless 802.11ac connectivityOptimized performance and operation according to automatically detected LAN speedHighly secured operation of applications such as password protected exit, hidden control buttonsWireless BTLE 4.0 Bluetooth as well as connection to USB peripheral devices for either table- or wall-mount installations, using the included USB cableHigh-resolution 2MP HD front-camera operationsPoE, PSU, and battery powering optionsMounts on tabletop or on-wall

2 x Tubes RCA VT-107-A ( same are 6V6GT ) with good Values. The items are shipped with German Post. 371Z